The GOOD, BETTER & ULTIMATE Way To Clean A Bike Chain For Free Speed & Longer Lasting Drivetrain!

No video

The GOOD, BETTER & ULTIMATE Way To Clean A Bike Chain For Free Speed & Longer Lasting Drivetrain!

Рет қаралды 136,507

road.cc

Күн бұрын

Пікірлер: 106

@robertlight2370 2 ай бұрын

Use an old shoelace to floss the cassette. It's easier than using the edge of your towel.

@Mgrant8163 2 ай бұрын

First ride yesterday on a new chain and cassette. Also, it was the first time using a waxed chain. It was like butter! No chain sound at all, super clean. I loved it.

@madplanet3351 2 ай бұрын

For these on a budget..remove cassette and chain. Place into old washing up bowl. Apply half a mug of the readily available 'Elbow grease 'liquid along with very hot water. Swish around with old brush. Repeat until water is clear. Remove and dry. Radiator is good in winter. Use Elbow grease onto a cloth and clean chainring Reassemble everything they apply silica secret.

@nigelwilkinson-xg9us 2 ай бұрын

Clamping the top tube scared me 😅

@Dimashoey 2 ай бұрын

haha me too...but knowing his bike is allez, it isn't that scary

@alistair410 2 ай бұрын

I think its OK to put your bike on the work stand using the top tube as long as you don't put any force on the clamp, let gravity do most of the work. If you clamp your bike using your profiled carbon seat post you have to apply a lot more clamping force to hold the bike there. Where would you clamp a bike that doesn't have a seat post, there are a few of them around.

@thegrowl2210 2 ай бұрын

Why do these KZfaqrs keep doing this?

@nigelwilkinson-xg9us 2 ай бұрын

@@alistair410 good point

@kmmntrls 2 ай бұрын

Its alloy

@winstonshaw2533 2 ай бұрын

one of the better videos on quickly cleaning your chain and deep clean put WD-40 isn't a degreaser.. Gunk degreaser is great but one thing I personally always do using a chain Bath always use diluted washing up liquid to get the degreaser out of the chain followed by clean warm water

@suisinghoraceho2403 2 ай бұрын

There is a WD40 branded degreaser. I guess they are using that rather than actual WD40, which is bad for your bike.

3 күн бұрын

While WD40 is primarily a penetrating fluid (WD40=Water Displacing [Concoction] formula #40), but it _is_ petroleum based, i.e., a degreaser.

@mboretzki 2 ай бұрын

I'm mostly riding in dry conditions and only on tarmac. I degrease my chain every +/- 1.000 km completely with Muc-off degreaser. Then I rinse it in hot soapy water and lubricate it afterwards. My last KMC chain made it about 16.000 km and was only 50% worn which is considered enough for a change on an 11-speed cassette according to some bike mechanics I talked to. Let's see how long my new Shimano chain will make it...

@luzzyrogue 2 ай бұрын

5000km

@GummeeH3 2 ай бұрын

I've got an alternative for biweekly-ish cleanings: shift into big/small, spray the chain with your spray lube of choice (lately I've been using Boeshield cause it tests well on the chain wear tests), then grab the chain in your dirty chain cleaning rag and run the chain in an S pattern thru the rag using the top and bottom of your hand. That will get the rollers on both sides. Alternate on the sides of the chain. Clean off the jockey wheels and floss your cassette with the edges of your rag. Done. Is it spotless? No. Has this worked for almost 40 years now? Yes. You should probably still do a deep cleaning once a year, and you should re-clean after every rainy ride, but for a 'quick, keep it mostly clean' cleaning and lubing regimen, this works.

@Akira-xc2zi 2 ай бұрын

I like this method, I do the same.

@kenkool5979 2 ай бұрын

WD40 is not a degreaser

@garyrobinson312 2 ай бұрын

Fairly sure he was using Wd40 bike degreaser, not the multi purpose stuff

@richardgilbert5339 2 ай бұрын

It certainly isn't,if you've got a tin of it in your bike tool box bin it. I've heard of people spraying it down gear and brake cables for lube???? I'm glad he mentioned chain direction when reinstalling the chain,made that mistake years ago before I knew better, drivetrain sounded worse than before I cleaned it.If he's being that thorough he should've removed the cassette for a good clean. Warning people that degreaser and bearing don't mix.

@KOL630 2 ай бұрын

You say that but it’s very effective at cleaning chains and metal parts. It also thins out grease in bearings so not a good idea to spray into parts like hubs etc. so technically it does decrease to an extent.

@jeremynorth 2 ай бұрын

WD stands for water dispersal. It's hydrophobic

@Leo-gt1bx 2 ай бұрын

I actually is look it up.

@hal9058 2 ай бұрын

The Silca wax system makes chain waxing much easier. It's faster, much more thorough/efficient, and compact setup

@siners77 2 ай бұрын

Good informative video, hope some day someone would think of adding a video to adjust / tune, changing gears !!

@VladThe333 2 ай бұрын

I cut off the top of a plastic bottle, screw on the cap and pour solvent into it. I immerse the lower jockey wheel of the derailleur in this container and simply pedal backwards

@bcc1955 2 ай бұрын

But will remove grease from jockey bearing right?

@VladThe333 Ай бұрын

@@bcc1955 there is no bearings in my pooley wheels 🤷

@bullbagaren1590 Ай бұрын

Regarding the silca wax. You can basically put the chain in boiling water and the wax still wont come completly off. Now running waxed chain no matter the conditions

@tomaburque 2 ай бұрын

Nothing cleans as good as a ultrasonic because nothing works on the inside of the bushings as well. If you don't want to deal with hot wax, there are wax-based lubes like Squirt which work great. I'm in a dry climate and currently using Muc Off ceramic which works for my needs.

@romanpramuka2703 2 ай бұрын

This video is April Fool's joke? I've never seen worst chain maintenance recommendations. It's full of mistakes.

@RegularJonMTB 2 ай бұрын

Going to some hot waxing this summer when my current chain wears out.

@bleckandbleck 27 күн бұрын

I have a Wippermann Connex chain with 15000km on it and it’s still not past 0.5 on the stretch guage. I wax it occasionally and use Super Secret Silca drip wax every 200km. Dirt and oil is a grinding paste and the enemy of the drivetrain.

@11robotics 2 ай бұрын

A chain only lasting 1.500 km is considered to be good nowadays? Good God. 11 speed chains easily last 3.000 km and 30.000 m of climbing under a heavy rider. Good thing those SRAM Red flat top chains are cheap as chips. But yeah, ultrasonic cleaners are the way to go. Easy to find cheap ones on Aliexpress, some large enough to also clean cassettes and at least the smaller chainrings.

@JFomo 2 ай бұрын

I ran my last sram red chain for over 15,000km with 200,000m plus of climbing. You're doing rookie numbers there.

@mboretzki 2 ай бұрын

@@JFomo I also don't understand what some people are doing with their chains. My KMC chain lastet for almost 16.000 km with 180.000 m of elevation. Changed it last weekend with about 50% wear.

@grvl307 2 ай бұрын

The chain on my winter bike that I rarely clean and dont wax lasts 3000-4000 km.. 🥲 10.000 km is a normal number for my waxed chains that I clean and rewax often. 1500 km is embarrassingly low.. 🫣

@11robotics 2 ай бұрын

@@grvl307 @JFomo @mboretzki I wasn't referring to waxed chains, but merely to regularly and thoroughly degreased and lubricated chains. Another factor is the rider weight, their power output and the prevalence of high power bursts, the pedalling technique involved (grinding leads to far more chain wear than spinning), the size of the chainrings and sprockets (smaller chainrings and sprockets lead to more wear), the prevalence of cross-chain use and even the amount of gear shifts under power. Those were also quite conservative values ("easily lasts" means it can do more). Long story short, the quoted longevity of my chains could easily be improved by 50-100% if a 65 kg rider (instead of 88) who mostly spins (> 90 RPM instead of my median of 82 RPM), rarely if never sprints and rides a 52/36 crankset (instead of a 46/30 one), while never crosschaining, was doing the exact same rides I do.

@cyclingjoezone 2 ай бұрын

Nonsense. 1500k is not a lot of mileage. Clean rings and cassette when you replace chain @4500km and don’t ever use wd-40.

@user-cx2bk6pm2f 2 ай бұрын

WD40 is lubricant dissolved in solvent. While it may do some degreasing, it will add some. Thus, the cleaned parts are not actually clean. Applying chain lube on top of another lube does not sound like best practice. Chain lubes, the good ones anyway, are made to adhere to clean metal.

@SlingsAxes 2 ай бұрын

400 to 1500 k? As in 400km 1500km?

@hendrikgoldammer659 2 ай бұрын

Chaining a chain after a couple hundreds of kilometers due to wear and tear would be completely insane, that’s for sure

@Craig_Beale 2 ай бұрын

Rock 'n' roll gold lube has been the best lube I have found so far, it goes on as a wet lube, cleans the chajn at the same time and doesnt clump or flake of like wax based lubes do

@bondy284 2 ай бұрын

Totally agree !!!!!! And have used different products on my chains over the years and this is the best in my opinion👍🇦🇺.

@ryansanchez7735 2 ай бұрын

yes, rock n roll gold is pretty good, no need degrease as it also cleans the chain. saves time and easy to use. clean looking drivetrain all the time

@matkvaid 2 ай бұрын

First thing - it is not possible to clean and lubricate at the same time - lubricant is not some kind of magic thing, it either lubricates or cleans, or it is just marketing. Also, this lube cannot be called "good", it is average at best in testings.

@ryansanchez7735 2 ай бұрын

@@matkvaid just sharing my own personal experience with it nothing more…

@nukez88 2 ай бұрын

I mean I guess it depends on the bicycle. For my MTB a chain is 4$ the shimano cassette is abound 10-15$. One of the more quality chain cleaning product's or de-greasers cost about 20$

@qwertyazerty2137 2 ай бұрын

Nothing (maybe apart from a sonic cleaner) beats a simple shake in a bottle with a brake cleaner. For the cassette just use a paint brush. It's enough to have the teeth and cavities between clean. No need to floss for a perfect clean.

@cryptobond0079 2 ай бұрын

Only the best for my chains and bikes. TDF Banana Wax Drag & Friction Reduction Racing Chain Wax. Clean you chain With Holts EGR Valve Cleaner before ultra sonic cleaning. Wax That Chain! ⛓️👍

@DanRoch 2 ай бұрын

Rotating 3 chains saves the most time, so you can bulk clean or wax.

@roadcc 2 ай бұрын

Good tip! Definitely!

@antonyadshead965 2 ай бұрын

I pressure wash the chain and cassette while on the bike, avoiding getting anywhere near any bearings. I want to blast the filth out of the chain and cassette, but not the grease out of wheel bearings etc

@oli4572 2 ай бұрын

Pressure washing the chain is an absolute nogo. You will avoid water in between the tiny gaps of the chain links by any chance. If you do so and oil your chain right after, you will trap water in these little gaps and rust there will be, also if you let the chain airdry after your pressure washing session. Nogo!

@stephencharles6932 2 ай бұрын

Not good. Wax your chain. Beautiful buttery smooth transmission and next to no cleaning palaver ( after initial set up).

@roadcc 2 ай бұрын

You agree we got the order right then? We love wax too!

@JasonMatthewCrabtree 2 ай бұрын

I don't think he watched the video through the end and he just missed that you did the waxing at the end. I think you got the order right though!

@michieltr 2 ай бұрын

Did you watch this?

@stephencharles6932 2 ай бұрын

@@michieltr haha, no! Didn't watch after the start of the ultrasonic bath part, thought that was it!

@leftyseel8658 2 ай бұрын

Is it ok to just use degreaser without rinsing? I also use an old shoelace to clean in between cogs, like someone here commented.

@khazza930 2 ай бұрын

definitely wash off the degreaser before applying lube (especially inside the links)... he didn't mention that bit... after degreasing, I usually use some soapy water on a sponge + brush (sometimes) then just water to wash off the soap... otherwise i find the lube doesn't last much

@philadams9254 2 ай бұрын

In B4 the 'just wax your chain' crew 😂

@JFomo 2 ай бұрын

Take the jockie wheels off but don't put them in the ultra sonic cleaner. The bearings are sealed. If you put them in the cleaner then all the grease will get washed out and you will not be able to regrease them. Just clean them with a cloth. Take the cassette of and brush it down with a toothbrush dipped in turpentine. The chain can be cleaned in a jar of turpentine too though you may beed about 2 or 3 jars of it. Reuse the turpentine for next time too so don't pour it out. Lastly soak the clean chain in mineral spirits, let it dry and proceed to lube or wax.

@roadcc 2 ай бұрын

Agreed, good tips! We like to ultrasonic clean jockey wheels with bushings but agree ones with bearings it’s best to stick to a toothbrush

@JFomo 2 ай бұрын

@@roadcc Yeah the ones with bushings are fine, no harm.

@grvl307 2 ай бұрын

Since I've started using hot wax I don't do all this stuff anymore. My chains last 10.000 km 😄

@kenleckie2359 2 ай бұрын

Start new and soak I gasoline 3 times then mix a teaspoon of Teflon power in melted paraffin wax and enjoy a extremely clean chain for upto 15,000km forget about oil and grinding dirt an filff

@thejuampi 2 ай бұрын

A year ago I accidentally bought a fake shimano 11 speed chain. Made it last 6000 km using the ultrasonic cleaner and waxing it. Not bad. I know an original chain can last 12000+ km if waxed properly every ~300km

@timetrialist 2 ай бұрын

Finally this bike channel talks about bike maintenance instead of selling bike BS

@paceline 2 ай бұрын

Can anyone recommend some consumer-level ultrasonic cleaners that fit a chain and don't break the bank?

@Sutlore007 2 ай бұрын

I have no confidence on re-apply the wax lube as I have seen people just dry brush the chain and re-apply the wax lube right away. Since the chain does not look so clean after finished, I feel like re-applying the wax lube like that 4-5 times later will eventually contaminate the chain. Would it be any other way to re-apply the wax lube properly?

@oli4572 2 ай бұрын

Wax does not attract any dirt or dust at all.

@richardgilbert5339 2 ай бұрын

Get him to clean my Vitus Sommet MTB drivetrain after a weekend riding in the north east of Scotland,then youll see a dirty drivetrain,or after a winter of riding 😂

@paullubbers939 2 ай бұрын

Use bio-degradable!!!!

@a1white 2 ай бұрын

Yes. The trouble with WD40 or GT85 is they contain PTFE which is a pretty nasty “forever chemical”

@nigelbradley613 2 ай бұрын

In the 2nd method you didn't protect the rotor and sprayed degreaser over it

@socopower 2 ай бұрын

Ah, that’s better then :)

@iann23 2 ай бұрын

A chain lasts between 400km - 1500km? Wow. Think mine has done about 20000km.

@peterwillson1355 2 ай бұрын

The WORST thing you can do is wipe a chain with a rag. You're just pushing the crap IN.

@aveedub7403 2 ай бұрын

Surprised to see presenter spraying WD40 liberally all over cassette and possibly overspray on rotor!!!! Take the wheel out or cover rotor with a plastic bag if you're gonna spray wd40 about! Imo. I prefer deep immersion chain waxing, just done two to swap out contaminated!!

@roadcc 2 ай бұрын

We had to save something for the better and best methods!

@alvaroodeh4794 Ай бұрын

Nothing like GUNK engine degreaser applied with a painters brush, no rubbing, no elbow grease no nothing, and the parts will come out as brand new ready for new Lube. Thank me later.

@JohannesCycling Ай бұрын

As if a chain would only last 400 km if one wouldn't clean it😂 Ok, maybe if it corrodes, but if it's lubed well it really shouldn't.

@therealbonj 2 ай бұрын

My microphone wasn’t working but I think I get the idea - use a deep fat fryer right?

@roadcc 2 ай бұрын

i feel a follow up vid coming on

@llargobike Ай бұрын

Nobody say you should not remove the powerlink once installed according to SRAM.

@stephenragland7710 2 ай бұрын

WD40 is the wrong lube and does attract H2O

@socopower 2 ай бұрын

Very good, but please clamp your seat post not your frame 😣

@konigsegg_1to1 2 ай бұрын

The frame is a specialized allez sprint, made of aluminium.

@socopower 2 ай бұрын

Ah, that makes sense

@Leo-gt1bx 2 ай бұрын

Hot waxing is the best way to not have to deal with all of this crap.

@oli4572 2 ай бұрын

But useless, as waxing is shown here...

@ianthompson6268 2 ай бұрын

I like to clean chains in kerosene. It cleans and lubes.

@stretch1396 2 ай бұрын

Gas

@curvenut Ай бұрын

too much work .

@lolbubs11111 2 ай бұрын

Only wax.

@therollingwheels1603 Ай бұрын

One of the worst videos about chain i have ever seen.

@mikeboux Ай бұрын

Instead of using all those products and equipment and time, why don't you buy a new chain ?

@xaviermorel4956 2 ай бұрын

First!

@xaviermorel4956 2 ай бұрын

Park tool CM 5.3!!!!!

@Celeritate7 2 ай бұрын

Just go to a car wash and bring a degreaser spray. Job done.

@bicikircho 2 ай бұрын

put bike on shower, get a hard brush, put some detergent on the brush, go thoroughly over the entire drivetrain, chain, sprockets, jockey wheels, etc. Rinse with water. Repeat 2-3 times if when rinsing water keeps being dark when falling from chain/cassette. Dry with a towel, once sure chain is dry, lubricate. I do this after every ride (65k or more)