The last Starlet Turbo conversion jobs! | Toyota Starlet 4efe turbo build.

Рет қаралды 14,417

Жыл бұрын

Time to finish off the physical turbo conversion of the EP91 Starlet. This episode includes: How to fit Glanza 4efte fuel injectors and test for leaks at the fuel rail, installing a Glanza vacuum tube for vacuum / boost reference hoses, Bailey single piston recirculating dump valve fitting, cold side intercooler pipe support bracket, spark plug heat range analysis, general re assembly of the front end (bumper, modified splash guard etc.). Hope you enjoy the episode.
Don't forget to like, comment, share and subscribe!
Instagram: @dan91sgarage
Disclaimer: These videos are meant as entertainment only. They are only a vlog of the work I have carried out on my cars and not meant to be instructional in any way! Working on cars can be dangerous and the results can cause harm to yourself, your vehicle and others! Be careful, be safe and only you are responsible for your actions.
#toyotastarlet #turbo #glanza

Пікірлер: 65

@tobysmith8369 Жыл бұрын

Awsome series 💥 very exited to see the finished product 👌🏼 Good work Dan 👏🏼

@dan91sgarage Жыл бұрын

Thanks mate

@user-ju3ig9nm9j 2 ай бұрын

Love this build. This is one of the only builds running the higher velocity inlet manifold. This suits the larger turbo your running. Have replaced the inlet camshaft for the 4efte.

@dan91sgarage 2 ай бұрын

Thanks, I think the increase in gas flow at lower rpm deffo helped spool the TD04. Unfortunatley I never got the chance to swap in a 4efte inlet cam. From the research I have done they have almost 1mm extra lift?

@user-ju3ig9nm9j 2 ай бұрын

@dan91sgarage yep, the 4efe inlet camshaft is the item that's holds of all the 4efe builds under 90hp. The 4efte inlet camshaft does deliver a big hit of torque around 4,000rpm. Such a shame about your build. One of the best alround builds I've seen. Alot of additional tunning in there. I'm just converting a ae100 corrola 4efe to a 4efte gen 1 tdo4l 13t build. Stage1 will be fit the turbo kit. This will be using the t-vis dual ported inlet manifold from the mr2 mk1 4age. And a masive 80mm mitsubishi galant 2lt 1990 throttle body. Fantastic build BTW. Keep up the great work, and some quality work.

@user-ju3ig9nm9j 2 ай бұрын

I'm thinking of trying out the det3+ I've always used aem piggybacks. If I could get your email address for a base map till it goes on the dyno, plus any extra help. Of course I would pay you for the base map.

@mattybyrne6203 Жыл бұрын

Nearly there dan bet your getting excited now I no I am to see it boosting down the road 😁

@dan91sgarage Жыл бұрын

Yes mate, deffo ready for the test drive!

@tomashorta6451 Жыл бұрын

projeto muito fixe tambem tenho um corolla 4efe mas atmosférico só com coletores e filtro de caixa kn e e muito fixe

@dan91sgarage Жыл бұрын

Sounds like a cool build 👍

@shardsoldier 11 ай бұрын

mate we wanna see a video of you sending this thing fkn oath, from the AU

@Nosixpack40Ryan Жыл бұрын

Good content Dan 👍👍 keep it coming, are you in Piggy back mode or FIT mode for the first start?

@dan91sgarage Жыл бұрын

Thanks mate, It's wired in for piggyback mode for this build.

@Sneycal 10 ай бұрын

Hey, i watch all your video and now i whant build torbo 4efe on my corolla!!! I will try do it in Ukraine! Ty for your guide's

@dan91sgarage 10 ай бұрын

Thank you for watching, good luck with everything.

@rollyae82 Жыл бұрын

So close to my pov passenger seat drive ha ha!... fantastic work.... is your starlet color code 7ga? Panama blue? looks similar to my nova project

@dan91sgarage Жыл бұрын

Lol, looking forward to it! It's 8K9 Purplish blue metallic paintwork, looks light blue metallic on film, but when you see it in natural daylight by eye it flips gently from purple to blue. Loving the insta content on the novarolla by the way, top work as always. 😎👍

@rollyae82 Жыл бұрын

@@dan91sgarage ha i bet you are! you are so patient.... interesting paint they had in the 90s... mine says Panama blue and in some light almost looks wrx blue then it also reflects oceon green... cant wait to get it polished up after i respray some bits.... thank you!...

@djfrankieflowers 7 ай бұрын

Great job! I want to put a Civic water cooling radiator in my E11 Corolla with 4efte engine. I know I have to move the lower water exit from the right to the left to align with the Toyota standard. I also need to make brackets. What do you suggest? Thank you.

@dan91sgarage 7 ай бұрын

Start by measuring the height of the front area the radiator will fit into. On the Starlet the mounting brackets you can buy bolt to the bottom of the front cross member and off the top of the slam panel. You might be able to weld / rivnut the Starlet brackets to the corolla. To be honest all you need is 2 x L brackets for the bottom mounting posts and a flat smetal bracket to hold the top post. All with rubber grommets to line the metal so it doesn't damage the radiator.

@84eighty. Жыл бұрын

What size intercooler are you running, the kit i brought requires most of the bar to be cut up to fit, but yours fits well. Cheers

@dan91sgarage Жыл бұрын

It's from Toyosports (140 x 65 x 550mm). The linked video below starts a short series showing the process of fitting universal intercooler and pipe kit (including bead rolling pipes) to my EP91 NA+T build: kzfaq.info/get/bejne/l85ihpeZm5rJnKM.html

@user-dn5wm3jt1j Жыл бұрын

Привет 🖐ну что кокда первые тесты на дороге??? И ещё вопрос почему к турбине подходит только масло а где анти фриз на охлаждения турбины?))

@dan91sgarage Жыл бұрын

The test drive video is coming up soon. The TD04 does have water cooling ports on it however I have chosen not to use them and just let the oil cool and lubricate it. In its original position on the subaru engine it is very close to the engine and gets very little air around it. Mine is positioned right in the air flow from the grille so it should be cooler in general.

@thanosmaganiaris2960 5 ай бұрын

hey, may i ask why you have the corolla manifold instead of the stock one? does it have better air flow?

@dan91sgarage 5 ай бұрын

This video explains it best: kzfaq.info/get/bejne/gZeAY9Ni1Lzek6c.html I found it had better low down torque and pulled to the redline better. The stock 4efe manifold was strangled at about 4500rpm. The corolla manifold is the best bang for buck power mod for an EP91 N/A 4efe. It is also the best all round performance charachteristics for EP91 4efe + Turbo builds. Over 150bhp turbo = 4efte inlet manifold and 50mm Throttle body. In my opinion.

@thanosmaganiaris2960 5 ай бұрын

@@dan91sgarage thanks you very much. I appreciate it 🙏

@morrisoo543 Жыл бұрын

question. i have a problem with my own starlet. the fuel cut is going crazy and im new to the det 3 and tuning in general, i dont no how to fix it, when its on vacuum it run great but when the turbo starts making boost it immediately runs super lean, as far as i know its a fuel cut problem. can you help me out, love the vids. keep it up, cheers

@dan91sgarage Жыл бұрын

Did you replace the 4efe 1 bar map sensor in the engine bay with a 2 bar Glanza map sensor? Or do you have the Det3 + with the built in 4 bar map sensor? You can't use the 4efe 1 bar map sensor with boost. What injectors are you using?

@morrisoo543 Жыл бұрын

@@dan91sgarage im using the det 3+ sensor, and Toyota paseo injectors (225cc), i’m probably upgrading to 325cc. What it does with 2000 rpm in vacuum its running Good but a bid rich, but when the turbo starts making boost , only 0.10 bar it immediately runs lean and bogs out, also i dont have the ignition wires plug in the det 3, cheers

@dan91sgarage Жыл бұрын

@@morrisoo543 Ok, if you're using the internal 4 bar sensor you need to set the Setup tables to Modify= Analogue in #2, Load= Analogue in #2. This will then use the inbuilt 4 bar map sensor. The 225cc injectors are too small you need the Glanza 295cc injectors or about that size. I haven't tried your setup but you will most likely have to add a lot of voltage in the det 3 fuel table and it will still run lean. If the det 3 output you send to the toyota ecu is close to 5 volts, the Toyota ecu it will perform boost cut (feels like a rev limiter). Definitely get bigger injectors as they won't fuel enough for boost. Also you shouldn't drive in boost without the ignition wires intercepted as you will need to retard the ignition in the det 3 on boost or the engine can be damaged.

@morrisoo543 Жыл бұрын

@@dan91sgarage Maybe Some infomation That can help, om running a ihi vb6 turbo with a 63mm down pipe and exhaust pipe with a cat and 1 muffer, stock intake manifold, brown 225 cc injectors, 63mm intercooler Piping, aem wideband and a det3+,

@morrisoo543 Жыл бұрын

@@dan91sgarage thank you i wil try it, thanks mate

@juansantamaria1480 4 ай бұрын

Hello Dan, to complete the conversion to 4EFTE I just recently bought a 4EFTE ECU but based on your experience which sensors did you changed?

@dan91sgarage 4 ай бұрын

Are you fitting a 4efte engine?

@juansantamaria1480 4 ай бұрын

@@dan91sgarage no I will install a turbo on my FEFE

@dan91sgarage 4 ай бұрын

@@juansantamaria1480 Wow! that will be a nightmare. If its a 3 plug 4efte ecu, you will need the 4efte engine wiring loom and the "under dash" loom from the donor car. 4efte distributor, ignitor/coil pack, knock sensor, throttle body with TPS, inlet manifold with idle control valve...etc. Unless you can harvest all the parts from a donor car it will take a long time to find all the bits. And the 4efte ECU is setup to run a factory 4efte with low compression pistons, not a 4efe with high comp so the timing may not be safe anyway. Better off with a det3+ or go full standalone with new engine loom in my opinion.

@juansantamaria1480 4 ай бұрын

@@dan91sgarage Hello Dan, thanks for your response, I bought the 2 connector 4EFTE ECU, dues that need all those parts as well?

@dan91sgarage 4 ай бұрын

@@juansantamaria1480 Don't think you'll need the under dash loom. The wiring loom plugs you have might fit the ECU but the wires will be in the wrong place. The ECU will still need the engine loom and 4efte sensors / distributor setup to run. Still a nightmare to find the parts and rewire the plugs.

@tharinduts2000 Жыл бұрын

Hi dan i need help to build my car someting wrong wz engine all was its miss can not accelerated

@dan91sgarage Жыл бұрын

What car do you have?

@tharinduts2000 Жыл бұрын

@@dan91sgarage corolla ii same 4efe

@tharinduts2000 Жыл бұрын

If i can have ur no i can wats up

@dan91sgarage Жыл бұрын

@@tharinduts2000 Have you checked the onboard diagnostics for any fault codes? What year is the vehicle? What modifications have you made to the vehicle?

@tharinduts2000 Жыл бұрын

@@dan91sgarage hi still i did didnt up grade .But suddenly this matter came

@emscorsa Жыл бұрын

What radiator you have ?

@dan91sgarage Жыл бұрын

It's a Honda civic alloy half radiator, 2 core, with special brackets to mount to the Starlet. Makes a lot of room for turbo stuff . 👍 Fitment video: kzfaq.info/get/bejne/iNZxZbdmnZ-9XXU.html

@SG-wp6sg 7 ай бұрын

Where can i get one of those intakes?

@dan91sgarage 6 ай бұрын

They come from the 8th generation Toyota corolla (bugeye) E111 model with 4efe engine. Third generation 4efe engine, also found in late model JDM EP91 Starlets. I found a seller on ebay with a complete engine and asked to buy just the inlet manifold.

@SG-wp6sg 6 ай бұрын

@@dan91sgarage They are a little hard to find.

@dan91sgarage 6 ай бұрын

Yes, it took months for me to get one.

@SG-wp6sg 6 ай бұрын

@@dan91sgarageUpdate: i just got one for $80 but without throttle.

@antonykhadondi5316 Жыл бұрын

Hi why change the injector

@dan91sgarage Жыл бұрын

@antonykhadondi5316 The standard injectors are 195cc and they can only supply enough fuel for 100bhp when the engine is turbocharged. I was aiming for more power than this, hence the change to 295cc's

@user-ju3ig9nm9j 2 ай бұрын

He knows his shit bro.