The method of repairing broken axles by widening them is stronger than before #method #repairing #broken #axles #stronger #before
Пікірлер: 28
@user-fs2wo6up9p11 ай бұрын
Смотря ваши ролики,я подумал что у вас вообще нет дождей. А вот он! 😁
@fidelnavarro50649 ай бұрын
Waoo !! Excelente Hermano. Gracias
@michaelopere542410 ай бұрын
Good job,the job looks very neat.
@georgegonzalez24769 ай бұрын
Thing you learn first hour of welding class: welded areas are weaker and more brittle than original. This axle has already been welded and has failed again. It takes a whole lot of confidence to think this weld is going to work better than the previous one.
@hamadmengal67164 ай бұрын
Laa jawab
@petertyrrell6690 Жыл бұрын
I would think that the weak "links" would be the heat affected zones after welding. As you're going to weld on your lathe anyway, wouldn't it be just as strong if you bored the hole as you did, tacked the shaft to inside of the hub, and then filled the hole with weld? Thanks for sharing.
@rolandolaureano246110 ай бұрын
Excelente trabajo 👏
@donraptor615611 ай бұрын
Let me know how long it doesn't last!
@dont-want-no-wrench11 ай бұрын
looks fine to me
@trailblazer104710 ай бұрын
Good Job
@paulorth2251 Жыл бұрын
Hope it holds up as well as expected.
@sptomcat86611 ай бұрын
給點讚,但是:我懷疑這個動力軸心能撐幾頓貨???
@GustavoSanchez-eh8lc9 ай бұрын
Regular nunca se debe soldar un eje en la parte interior la soldarura le afecta y y parte
@cherpiu584210 ай бұрын
Buenísimo 😅
@dont-want-no-wrench11 ай бұрын
shorter by a bit than original, innit?
@davidhamm562611 ай бұрын
But, you don't need a lot is most spider gears...
@utkuozcan439610 ай бұрын
Axle short 2 cm more, its ok ?
@sheriffdeen17511 ай бұрын
Good job
@greenhat774211 ай бұрын
Гудронум!!!
@user-pg4pu8cw9k10 ай бұрын
Полная охинея! Лопнет на первом километре полной загрузки машины!
@user-br3zd5ur5q10 ай бұрын
Несогласен, при полной загрузке, учитывая как они грузят он вряд ли тронется.
@polishedturdspeedshop11 ай бұрын
When these guys frame a house I bet they still find a way to get a lathe involved
@dont-want-no-wrench11 ай бұрын
most important machine tool
@rasolfahry10 ай бұрын
فنان شغله روعة
@bretlovitz306810 ай бұрын
There is a reason this was made as one solid forged piece. This shit job won't last on their grossly overloaded truck. I love reading the comments and seeing all the people who praise them for this crap. They, like the people doing the work, have no understanding of the forces on the axle.
@PeterChapman-rg6gr10 ай бұрын
Most of the 1/2 shafts on our vehicles were made in 2 parts and friction welded together followed by stress relief and then heat treating. We had lots of failures on both the weld and the shaft shattering.
@user-sj3gh6tf2x10 ай бұрын
Полуось порвало не от крутящего момента,а от люфта на подшипниках....
@user-br3zd5ur5q10 ай бұрын
Может и подшипники а может мост гнутый , это не важно полуось уже не спасти.