so did u use it yet?

I know I would...

Pull a deep enough and long enough vacuum... any water or condensation will sublimate... and there won’t be any moisture.

@@nsboost lol, ya really

@@jacklegminercanada3866 I’m a HVACR technician. So funny thing about vacuum is... is under vacuum, the freezing point of anything raises. (Kinda like the radiator in your car being under pressure, which raises the boiling point). Do you have a vacuum pump? Put a shot of water in a glass and put it under vacuum. You can freeze it at room temperature. In HVAC there is a concern in the community if you pull a vacuum on a refrigeration system TOO fast you will freeze any moisture in the system. Well in a small blasting tube, you IMMEDIATELY pull that small space into a DEEP vacuum.... and any light moisture is going to freeze. Pulling a vacuum before or after probably will produce near identical results either way, So though “pulling a vacuum before freezing” is logical, the fact is you probably froze any moisture in the tube when you put a deep vacuum on it (in seconds) anyways. And yes... you hold a deep vacuum long enough, the ice will sublimate. It’s physics.

@@nsboost I have a robinair 2 stage. Haven't used it really. Just to distill isopropanol.

I have this now.. double the size column planning on running about 1,200 ml worth of butane through it

you could but id do it at different times do your first run then put aside then do the second so you can see the difference.

Unless you worked in Europe, you probably didn't do much work with recovering hydrocarbons. Or maybe you did. The US doesn't have much r600/r600a system to work on.

@@jonosterman2878lol how is recovering refrigerant any different other than the flammability aspect ?

Nicholas Hamil sure after you have extracted you can use everclear to help it out and now they just upgraded the mini a lil bigger and with splatter platters for a easy pour

They do offer that splatter platter for extra. I think a 4x4 spool, platter, and extra gasket and clamp would run a little over $100

Rational Bushcraft it is🖒

you dont have to buy butane you can reuse it over and over in a closed system

+kody “sorrynotsorry” Frase under vacuum apparently not. i think thats what i heard... bc i thought that too! .... but i think when you lines, tank and the material columb is under full vac it doesnt need all that extra... but im no CLS expert

1 can doesn't even go through a large blaster. The rule has always been 1oz per can. I have 8 oz blaster that works like a charm. Just shake!

MrNewmanRay thanks for watching

+Medicated Fish never mind... I just watched it again LOL. I love this mini.

+Braxton Wanner butane

+AmerikanPBT i doubt your doing much of anything wrong, alot could have happened during shipping. to make sure I dont have any mishaps during a run I do a dry run/distill to test and clean. before you do a run with material do one with out and when your done wipe out the empty equipment with a tack cloth to clean the mystery oil and you can test everything at the same time so you will be killing to birds with the same stone. hope this helps and will try to help more if needed

try some thread tape, gas line thread tape.

+Donald Griffin I usually dont ever mention a return due to everyones material they use is different and have a few that go on every word I say so when they dont get a return as well I do they freak out and start calling names and bashing the equipment and stuff. and you can follow the directions they give you so you can weigh your butane and extractor and know the limits to put in. hope this helps and sorry I didnt mention returns. and also all strains and even plants run different and get different returns

+dirtybongwater grows meds Thanks for answering the first question, its more important than return I agree. How many cans of Tane needed for run.

the mini varies the simple unit uses one can and it goes up from there when you upgrade the instructions will tell you the weight that is needed of butane and all cans of butane have different weights so you will have to follow the instructions and weights for the extractor and upgrades that you have or gonna get

with the mini 10 to 20 ponds will do great and get pellets if you can, the block will work too just more work lol you can get away with 10 but always good yo jave extra

+dirtybongwater grows meds thanks for setting me strait brother, your a star. Cheers

+Donovan Garcia on the BVV site that I mention on the vid

Exactly!

I'm a chemist, so I want to explain things a bit here. While you would be correct that heating the vessel while pumping the vacuum and then chilling after would produce a harder vacuum it is actually pointless in this scenario because the vacuum itself goes away the second you add the butane. It is not the actual vacuum that is important, the only important part is that only butane gas is in the chamber and no air, which itself exists at high pressure not low pressure. The reason for this is that air, when in contact with the cold surface of the receiving vessel (the one in the dry ice) wouldn't do anything special other than become cold air. Butane gas however as it gets cold will condense into liquid pulling in more butane gas from the source vessel in the process. Therefore if you have too much air mixed in with butane this process slows down and it takes longer to move from one vessel to the next. But once the process starts there is no vacuum it is all at high pressure. So there is no actual benefit from producing a hard vacuum in the first step.

+Jeffrey Phillips Freeman so how exactly would you recommend doing it

I saw the cooling as a waste of time but pulling a vacuum on this system with what I would assume is trimmings is going to take some time as the moisture comes out of the product.. What kind of time is needed at this point?

ViralTuber how much butain should a 6"×4" pot hold?

You are so want to pull the vacuum before you chill When it's chilling with no vacuum the atmosphere will create ice and the ice will not vacuum out common sense

just leave it in there for how ever long you want

no need, the majority of the actives are removed extremely quickly.

Jeff Jr could be a number of thing but the most important is the material you put in, then also if you using dry ice or not (and yes it does make a difference). also if your able get a small ball valve for your mini so your butane has a chance to really take effect for a few minutes. also make sure you top off the the tank after every use it needs to be full before every run to make a good extraction. hope this helps but please remember the minis wont produce the way the bigger units do because of the amount of material your using. also try to remember if you put bad material in it and except it to produce a great end product thats not gonna happen, but you put in fire you will get fire back. the ball valve should help it soak some more and try the other tips. hope all this helps and would love to hear if they help

+Donald Griffin you dont have to have dry ice but things will go alot slower like 10 times slower lol. a run with dry ice will take around a hour where a run with just ice can go longer then six hours. the minis will go a lil faster but dry ice will help everything run alot smoother and faster. hope this helps

check out #BestValueVacs.com and ask for josh or grant and they will get you what you need

bump or oil slick paper

MrNewmanRay I think they go for 560 but check the site and dont forget the discount code DIRTY

when that pumps stops making all that racket u just wait like 2 min and u are better than -29

Why ?

what?

@@AlexiasPlaylist He's saying he talks too much.

Jerry Berkey lmao

1.25x playback is key. lol Interesting set-up though.

Note to Millennials, the video is less than 20 minutes long. How hard can that be? You can also be checking you phone while watching the video to make the absolute best use of your precious time. Then there is your Cheetos stash you could be dipping into, completing your trifecta...cause nugs make you soooo hungry.

ajradel that was over a yr ago but i believe a lil over 6grams

yea im wondering if i could do several runs with the mini or just spend the extra on the 1lb.

ajradel id go with the bigger scalable system due to you can always build it bigger if needed the mini is great for testing product

Its 45g of product in to get 6 grams of wax? Doesn't that seem like a lot of loss? I'm new to this so I'm just trying to figure out if that's normal or not.

not a bad return

Mark Howell I believe they are 580 on the site

dirtybongwater grows meds

Make brownies out of pot

I want to learn how to make brownies out of pot

D0mom

mario juana thanks for watching, for some reason it always makes my day when you leave a comment on my vids thanks again

18matts a mixture of 90 to 10 is ok and thats 90 butane and 10 propane. propane has high pressure possibilities. i guess its up to the tech, but the with the mini id just go with butane

18matts a mixture of 90 to 10 is ok and thats 90 butane and 10 propane. propane has high pressure possibilities. i guess its up to the tech, but the with the mini id just go with butane

👍👍👍

People get excited making videos. It can be frustrating but just get used to jumping forward and being understanding. Blessings friend.

Yes - a charitable attitude, JA. But at the 6-minute mark I still had not a clue what he was on about, absolute babble, I gave up