How long until I kill it again?

Just want to remind you of this... air/fuel screw only adjusts the mixture at idle, main jet controls the mixture for everything else. Unless your snorkel filter is clogged or really restricted it’s probably lean so you need a bigger main jet. You could also drill and tap the snorkel, then install a fitting and hook the suction side of the catch can to the air filter side of the carb, that will still provide some suction off idle and not cause a vacuum leak. That’s how they set them up from the factory, just without the catch can.

Damn, man. I’ve been with you (subscribed) since you did that video your new racing project back in 2011. When you had like 43K or so and now look at you. Almost to 300K. I’m proud of you man. It seriously made me smile. Keep the content rolling. 👍🏻💪🏻💯

I’m very excited to see the Murray running again:) I’m really looking forward to seeing it on the trails again

Glad to see it fixed up, If you decide to run your snorkel again I think youll have to rejet your carb, I had to do that when I put a snorkle on my Honda 300 fourtrax, the Airfuel screw just didnt have enough adjustment. I just kept drilling the main jet out with a Numbers drill bit set, they are tiny and go up in really tiny increments. The trick I used to figure it out was Id just put my hand over in the inlet of the snorkel and It would run good, then bog bad when I pulled my hand off. as I kept drilling out the jet I had to cover less and less of it with my hand in order to get it to run right. Ran strong after I got it tuned right.

honestly Im just curious, what happened to the craftsmen crawler because i have looked around for a video but couldn't find one

You have the pulse line on your fuel pump hooked up directly to the intake creating a lean condition because the engine vacuum will suck air through the vent on the fuel pump. The pulse line on that pump in an OEM setup is connected to a crankcase vent built into the dipstick tube and operates on the rise and fall of crankcase pressure as the piston goes up and down.

For the snorkel, connect into full sized pipe then into a tee down to slightly smaller pipes. Doing that and using 45s instead of 90s will allow better airflow.

So happy to see you making videos again! Cant wait to see what you have in store for us.

Glad she is ready to romp! Looking forward to seeing it in action. Warm weather approaching soon waiting for mud romp testing!! Keep them videos coming.

I did the whole evil eye light thing on my toro a few years back, it makes a huge difference and it costs basically nothing to do

Hey so I just want to say thanks for these videos! I got a Murray given to me the other day. I believe it may be the same kind that this is based on. I plan to do a lot of the mods you have done. I wont be able to do as much as you as I cannot weld but I want to try and bolt on what I can. This thing is a beast!

Heck you've redeemed your self. You shouldn't even had to ask. It's a good feeling to wake up and see that you have a new upload. Excited to see it ripping and roaring again.

Happy to see videos again. Yours are always the first I check out when considering a build.

I laughed my ass off at the jumper cables. "Must have a bad ground"

I can hardly wait for more mud romp videos Todd... Keep up the good work with the Murray...

Woohoo the Murray lives! You’re right it does have a lot more power then before. I can’t wait to see it out on the trails again.

Pretty cool! I won't be making an offroad mower but I DID by a Ridgeline this week...

Hahaha love it. It gets up n goes eh. Lol all the rideons around the yard good on ya.

Glad to see you have the Murray back up again!!!

Im juat glad you made a video missed these alot

Need to bring the murray down to western pa August 8th and compete in the Top Tractor Challenge!

Nice to see murray back running

I just love it Fearless front on my recommended I can't wait to go modding murry

Hope your new house and everything you’ve accomplished the last 2 years are all doing great. I’m sure the KZfaq ‘break’ was kinda nice to finish up your personal work. House looks great man, great job all around!

love the fact that you upload more!!!

It’s awesome to see that thing running again! But for some reason it sounds very different than before. (Is it just me? 🤔)

Excellent to see it alive again 👍

Yours is far more famous than mine, but mine is making a comeback after 10 years of sitting in pieces, with a few upgrades of course :) Still, very happy to see that black little monster running again!

YESSS THE MURRAY!!!!! Seriously though what about some kind of small (like a bonnet scoop) air intake duct on top of your dash where thy e old choke lever was where the snorkel comes upto... it on top of the dash so would be much better than behind the engine with regards to water and then it would be able to suck enough air? Just a thought... keep up the great work looking forward to the next romp

It's AWESOME to see the murray going again.

the murray with a 2 step would sound so cool!

Good job man. Nice to see you up and at it again. Keep up the good work.

Maybe you could make a air box around the filter and have a snorkel off that.

Thank god .. lol . Keeepm coming man . Always love your vids

nice to see the videos coming back.

Looks good buddy!! I cant wait to see some trail footage!!

Nice!! Got to get a vid with it on your track going wide open.

So glad the murry is back, also glad that you are back making videos again! Keep up the great work!

Awesome. I love the murray

Thank God your vlogging again!!! Anyway you can give info on the throttle, shift setup you have. Love that setup and would like to do a similar setup

Murraygeddon,or Mad Murray..to snorkel it properly you'll need black abs type pipe and have to use sweeps and 45s instead of 90s... 2.5" pipe should be sufficient for that engines needs...

YES!! Glad your back!!

Do a 90 degree up on it to move the filter up and get an uni foam filter them foam filters are better for the dirt and let a lot more air in

I will be happy to see the Murray in more video

Sounds good can't wait for a romp vid bro

Love your videos everytime new ones come out

Put a 45 elbow on the filter and move it up to the top of the motor.

Its Nice seeing you Come back😃

Welcome back!!!!!!!!!!!!!

Nice 👍🏼 glad to see you man

Wait so can I just take my coil wire off and use the pull start that I made or use a battery to jump it given that I have no ignition switch whatsoever? It's just the connectors sitting there and I don't want to wait for a new one it's just a fun mower. Thanks

hell yeeeeeah dude bring it on with the damn murray! cant wait to see that thing shred in the mud again nice job!

You have gone a long way and I'm just happy that you're getting it done when's the next mud run going to be

Yay more vids! What kind of rear end is that?

Have you ever thought of running chains it works very well

Heck yeah!!!!!!

Cant wait for more trail videos of this thing!

Woohooooooo

So we're trail riding mowers now? Sorta cool

You had the snorkel on it before and the same problem and the same solution. I think you need bigger pipe and keep it bigger then the intake of the carb. I see areas where it is smaller then the carb. That is like running the choke part way closed. You would have to put a fan in the system to compensate for the smaller pipe and that's not practical.

now get some damn ags on the back! so you dont get stuck anymore. may need to full them with window washer fluid or something thogh you dont look to rear heavy.

keep up the good work

where have you been? how longer before we get an update on the racing mower (remember that thing?)

Love your video

Seeing these is making want to take my yard pro out of retirement

My mower is hard to put in gear. And it will not stay running if I release the clutch even if in neutral

Excuse me mr christopher my mkwer has a snorkel aswell butbmy one goes up instead of it being in the dashboard and also if u do that then u will still get air if ur under water a bit

Missing these videos wishing for more

What size pulleys do u have on it to make it that fast?

You should do a update video on the old sear suburban diesel it’s been a while sense anyone has had a update on the tractors condition

Hi i have a 1970 sears that i got for free like 2 weeks ago i put dual on it and put a new carborator on but i want more speed and want to go mudding what is the best pulley ratio

YEEEEEES......its been to long 😍😍

Where you been man? It's been a while since you uploaded?

Love watchin you!👊🏻🔥

Let's go a ride now......... #MudMower's

Why did you put the lever on your shifter tried looking back and some of your old videos but couldn't find it...good job

I don't know if this allowed but I need a 1998 16 hp voltage regulator briggs and Stratton

Cant wait just don't kill it lol

Shes a runner .

What tractor would you be scared of more to ride on ?

You can't stay out of deep water - that is funny

Hey do you know if u can still get those honda gx200 racing engines. We looked on that website, NR racing.com

Why the exhaust sound different?

Has it really been that long?

Who thinks it would be cool to turn an old FF/24 sears craftsman tractor into a mud bogger!! or trail rider. idk. that would be cool, to me anyways.

if u kill this engine get a708 vtwin they have a good sound to them and they are like 22hp from the factory throw in a cam some forged rods and pistons new valve springs and u can get 35+hp out of them easy at about 3500revs

👍👍👍👍👍👍👍👍👍👍👍

Where's the sears?

I can’t what to see fucher video

why not run the snorkel up and out so it can get a ton of air

Compromised he said, I watched it twice still don't know who he's talking about.

Make a 90 and just lift the filter up a bit

i want to buy it

Shoot It

it was not runing lean it was actually running way to rich

Drugs make things way to complicated 🤣 put down the pipe

Kkkk

Hey Todd, Always been a big fan since i found your video online 7 years ago. kzfaq.info/get/bejne/kKeGZdiC19SpdoE.html. I was wondering if you ever thought of converting an electric lawnmower to a racer? Would love to see you do that. Just a thought.

First