The trucks broken rear axle housing due to overload was pressed into amazing service by re welding #restorationtoolshop #broken #truck #overload #restoration #service #welding #damage #reaper
Пікірлер: 121
@GrumpyHarleyRider10 күн бұрын
Have these guys ever heard of a grinder and weld prep?? That job will be good for one overload and it will break again.
@thepubliceye9 күн бұрын
Pay more attention and you may learn a thing or two.
@donaldcasselman7 күн бұрын
Good for future business😊
@mangopog98145 күн бұрын
Legend has it there are truck rears in India made of 100% welding rods.
@brandonclifton20278 күн бұрын
Slightly better than repairing it with wood.
@BubuMarimba6 күн бұрын
these guys do miracles! In EU the workers will just order the part from the original manufacturer and pay like 1/3 of the truck cost if not more and guess what? The new part will fail next week.
@bobkids0097 күн бұрын
They have all the necessary basic tools required to execute the extreme rectification job coupling to the skilled worker in place make this task a successful accomplishment. Well done my friend......appreciate all the hard work put in for this video.
@mangopog98145 күн бұрын
And another failure in the future not to mention welding cast steel which is a huge no, no.
@michaelallen1432Күн бұрын
Its like people are not watching the same video im watching. To respond to thr criticsms: 1) "they didnt straighten it out so its still misaligned." Yes they did. They put it in a big press and adjusted it. I can't say for certain they hot they alignment right. But it certinly was addressed. If its not alighned its not because they didn't bother irys because they made an error and didnt get it straight enough 2) "They didnt grind it out they just welded it up so the weld is contaminated and weak." Not true, while they didnt use a grinder, thry did v out the crack. They used arc gouging instead. Perfectly good technique. 3) "its cast iron sp it will break again": Look at the way the strap is welded to the top. Thats either stamped ir cast steel. I think its actually atamped, then thebpieces are welded together. 4) "They just welded the crack right across and it will break again" Once again, not true. They arc gouged the steel strap over the top and took a piece out. That piece goes from half way up on the round portion of the housing to half way down the left "tube" Then they arc gouged the crack, and then weldes it up. Once that was done they replaced the strap. The welds on the strap is not over the erld on the tube. In fact they are quite far from it. The one half way up the "pumkin" isnt in a stressful spot at all and the other is a good distance from the crack. Looking at the crack, the welds will be under tension. Its unlikely they willl break under those conditions unless its overloaded, but thats not going yo ve the shops failt. Since its mild steel if he properly chose his filler the repair should be close in strength to the original axel material. So this was a totally legitimate repair There are only a few minor things i would have done differently. For example i would have drilled the crack with a 1/2" drill bit.
@Mike-gc9ih8 күн бұрын
I wouldn't let them repair my wheelbarrow 😮
@user-lc5ny3ri8q5 күн бұрын
И все таки великие труженики!
@stevegreen24329 күн бұрын
Usually like what these guys try to do, but not this one! No weld preparation. Original reinforcement (not good enough for what they do to the truck) Is then cut off , but replaced with equally bad weld prep. And its now got a butt weld right near the max stress point! Surprised they actually did remove the reinforcing plate---I expected them to just weld the lot in one go !!
@davidhall887411 күн бұрын
Does anyone, besides Alvin and the chipmunks, believe this will hold beyond the first load?
@LexusGX460-OFF-ROAD10 күн бұрын
it will hold up.... however the owner will overload the truck... the welding is correct, the users overloading the axle is the cultural issue here
@DavoShed10 күн бұрын
I think there is a time to say “You trucks a bit rooted mate” Get another axel from the wreckers. (There is one there that has a rooted engine) I don’t think I could stand the constant discussion in real time.
@joseluispeinado52639 күн бұрын
P⁰@@LexusGX460-OFF-ROAD
@tempesttempest7699 күн бұрын
Do you really think that if it didn't work as it should be they'll be putting so much hard work in to it ?
@70elcamino579 күн бұрын
What about a little better heated up the axle while welding it get a better penetration and bond and clean it off with a wire wheel or some sandpaper
@fritzlehner90603 күн бұрын
I love these people !
@gordonwelcher95987 күн бұрын
I like the way the trucks are painted in rainbow colors and that the employees are allowed to wear dresses. 🌈
@juancarlosmiranda27362 күн бұрын
FELICITACIONES!
@specialized29er868 күн бұрын
Isn't prepping the weld area and giving it a good grinding required when using a stick welder.
@tonynaidoo75726 күн бұрын
That repair was done very well its stronger than the manufacturers spec.
@tinkernaut873611 күн бұрын
These repairs are useless, until they start using trusses on their axles this will just keep happening because the triple load their trucks.
@meandthemrs74034 күн бұрын
I was 19 minutes into it before I realized that it was no longer a drive axle. Very good repair. But why don't they weld in 4 gussets across the radius' to add some more rigidity?
@michaelallen1432Күн бұрын
The customer won't pay for it
@manoelmonteiro99635 күн бұрын
Muito top demais parabéns pelo seu trabalho maravilhoso
@COZMICTOM11 күн бұрын
I LOVE WATCHING THESE GUYS AND THAT CAPED CRUSADER
@saleem956ify6 күн бұрын
very well done, I have seen some of these repairs last long considering how they overload these trucks...
@Rollin-With-Kirk10 күн бұрын
See everyone doesn't realize See all the dirt everywhere, well that get's into the welds and makes the welds stronger than the original forging because it's better than borax, and see they don't wear gloves either and so some skin cells get in there also to help with no porosity and yeah 100% almost better than new, Oh and their shoes with no steel toe helps with their welding balance! =)
@edekoka62678 күн бұрын
You would starve to death there.
@mangopog98145 күн бұрын
Those are cast parts not forged, the reason it’s doomed, cast can’t be welded without bringing the part up to near melting point.
@inlinefourtr8 күн бұрын
Filmed on location in a backstreet in Birmingham UK 😊
@firstlast-ty4di11 күн бұрын
That man has serious arc gouging skills.
@tarciliobeneditodasilvafil39215 күн бұрын
Bela soldagem 👍👍👍👏👏👏👏
@paulorth22516 күн бұрын
Did anyone else catch that this axel had been previously repaired in the same way and it still broke due to overloading.
@ernestcotton93244 күн бұрын
Their weight limit is how much it can hold
@alro24346 күн бұрын
Truckers Motto "It is not loaded until it is OVERLOADED!" Good welds, bad prep and too thin and probably soft, doubler/reinforcement. Truss or gussets there
@howder19515 күн бұрын
I wonder if the original break had a defect in the bolster plate to crack so cleanly. Nice work with primitive techniques.
@namngothe20608 күн бұрын
The weld is very correct I believe it will bring very good work to you, I really like your video, your work is very good.man of the job
@speedybuggy16779 күн бұрын
Very true welding I do believe it will hold very great job you the man for the job
@thesay56635 күн бұрын
Great welding and ingenuity
@colblood442611 күн бұрын
done good for another 30 ton load then back to the shop for more welds
@thepubliceye9 күн бұрын
They can fix anything but they can also break anything
@jerrydosser70319 күн бұрын
Won’t last in the conditions it lives in!
@jayaramsn366610 күн бұрын
With such good and cheap repair facilities available, the truckers are shure to overload
@oilburner2257 күн бұрын
What a bodge up, as a coded welder (ASME9) I couldn’t bring myself to watch the whole video 😢
@traceypotts942510 күн бұрын
Love the skill so natural 😊
@augustinenwafor14827 күн бұрын
That is absolut nonsense. They don't know how to weld a broken joint.
@MrSandrobrecho5 күн бұрын
CLICKBAIT.
@TheJimbob160310 күн бұрын
Click bait I saw no giant rear axle housing as shown in the thumbnail.
@rfkcous8 күн бұрын
Same axle as the thumbnail, the small people actors were not in the shop.
@larryperdue50811 күн бұрын
You should on those axles those strips of plate steel before you wield them on is drill some one to 1.50 holes down the middle then when you wield them on also wield up the holes and that will make it stronger 💪💪💪
@marcusharmon8389Күн бұрын
King for a day c##t for a year 😂😂😂
@jaehoonjeong55736 күн бұрын
파키스탄형님들. 최고
@CarlosAlberto-ji2qq9 күн бұрын
eu tenho assistido vídeo desta turma e não me canso de ver tanta gambiarra é por isso q não falta serviço aí pra eles
@amiraldomiranda543710 күн бұрын
Its really impressive!😮
@donaldcasselman7 күн бұрын
I guess the welding mask works😮
@onofriolemonache780911 күн бұрын
do not overload the trucks and that shit do not happens
@SkillMasters-vy2lo5 күн бұрын
Good work
@prixalternative420110 күн бұрын
Good job 👍👍👏
@bernard34908 күн бұрын
Bon. On peut toujours rêver... Pièce soudée sans rectification de l'alignement du demi arbre Travail de soudure pas préparé Je ne donne pas cher que ça va re-casser sous peu de temps Des efforts pour rien... si peut être un accident avec blessé ou pire
@TheUltimate657 күн бұрын
👍👍👍👍👏👏👏👏👏😁
@ALEKS-ABIN11 күн бұрын
Отличная работа!!!
@rfkcous8 күн бұрын
Why wouldn't you put the reinforcement plate on the other side too as long as you had the axle out?
@user-ew6dh5cv2y7 күн бұрын
멋지세요
@syahrial66449 күн бұрын
Orang orang yang Memper Baiki dan orang yang Memakai Jasanya Mereka Lebih Tau dari yang Banyak Berteori,, Hornat,,
@user-gq5rk7oc3j8 күн бұрын
Trying makes Knowledge
@user-ot6tf6ph2o10 күн бұрын
Эта деталь, как и многие другие подобноремонтируемые, должна пойти в утиль и заменена на новую, но нет … а потом удивляются, что машины в обрыв летят😂
@user-dv1rg7oq5r9 күн бұрын
Вообще то балка сама по себе сварная и ремонт возможен . Естественно нормальными электродами и с соблюдением технологий .
@megavolt06749 күн бұрын
а где в Пакистане взять новую балку ?
@user-dv1rg7oq5r8 күн бұрын
@@megavolt0674 Естественно в Японии . Там на стоянках где продаются б / у автомобили есть пакистанская диаспора . Во всяком случае когда наши ребята гоняли японцев в Россию была , может сейчас что и изменилось .
@tmakis8 күн бұрын
@@megavolt0674 как где? отлить из обломков всякого гавна. как они делают все
@churochkin8 күн бұрын
для индусов и пакистанцев это не проблема -- еще нарожают
@user-bt1kx7hi1s8 күн бұрын
Надо было покрасить.
@user-vf5fx5yd1b9 күн бұрын
Детайла трябва да има фаска и тогава се заварява!!!
@user-ew2lt4vh8o9 күн бұрын
І до шнура і до пьона бардза праца пшердольона 😂
@user-bn4zx7qg2c9 күн бұрын
This is rubbish in its purest form, it's should last???
@user-wv8jc2lf3o9 күн бұрын
Это у них ПТУ, где учатся на сварщиков?
@podgee75078 күн бұрын
they must really over load the truck, to break that axel ???
@edekoka62678 күн бұрын
Is that elf in the picture welding it from the inside?The voices of the elves can still be heard in the background.Do you employ many dwarves?
@fernandomejia24988 күн бұрын
Exelente trabajo señotes, saludos desde California 🤝🤛🙏🇨🇴🇨🇴🇨🇴
@benk70819 күн бұрын
waste of time and money. It will break in no time. At least try to grind and clean the metal before welding. Maybe it will hold for 2 days instead of one!
@kontruksi31710 күн бұрын
Luar biasa 👍👍👍
@pdr592611 күн бұрын
Sometimes it is not the overload but the potholes. A punctured inner tire can also have the same effect as overloading.
@CarlosAlberto-ji2qq9 күн бұрын
Não tem nem como deixa o link com tanta gambiarra nesse trabalho
@aslamhsn770011 күн бұрын
How much money got work seller
@ivanmorari51339 күн бұрын
Супер уста
@bigturboxr3i9 күн бұрын
Good old British Tools still hard at work.
@agussoediro541511 күн бұрын
Kerja baik,Paman 👍👍👍👍💪💪
@waynekarjala203210 күн бұрын
These idiots overload everything by 30-80 % and then throw some more on for good measure. They should not be allowed anywhere near anything with an engine.
@TroubledTimes202410 күн бұрын
I always cringe when I see these guys get anywhere near precision areas, but they do get the job done, good on them.🙂
@jayaramsn366610 күн бұрын
With adequate reinforcement being given at the welded area the axle is very strong now. Hence also very strong and safe. A good job done.
@stevegreen24329 күн бұрын
There is NO reinforcement! They cut OFF the reinforcement, did a bad weld on the main casing, and then replaced the "reinforcement ", now in two parts, with a bad weld. Sorry--I usually like the work these guys do, but not this job---its crap
@stalkself9 күн бұрын
минут 15 думаю продержится, ну или до первой кочки или ямы
@HouseofQuotes-nl7up11 күн бұрын
Nice work sir ❤
@andrzejporeda728111 күн бұрын
Przepiękne jest to odrestaurowane pozdrawiam serdecznie serdecznie 👍👍👍🌹🌹
@rafaelduranpreciado91779 күн бұрын
Ellos, por su amor y dedicación al trabajo, sobreviviran a una catastrofe.
@tmakis8 күн бұрын
странный какой то чулок. ниша для редуктора заварена крышкой. походу просто ось для телеги.
@user-ir4yf8ci8e6 күн бұрын
А у них, на задней тележке, один мост ведущий, дальний. А это, ты прав, просто - ось подпорка. Экономят так.😁
@user-co6lj5co4z3 сағат бұрын
استاد کارهای ایرانی باید پیش شما شاگردی کنند
@sergt2919 күн бұрын
Putin gay
@gordonwelcher95987 күн бұрын
I like the way the trucks are painted in rainbow colors and that the employees are allowed to wear dresses. 🌈