The Ultimate Guide To Using JG Push Fit Fittings And Plastic Pipes

Рет қаралды 5,678

Күн бұрын

This plumbing tutorial show how to use push fit fittings and pipe and avoid making common mistakes. I will show you whats inside a JG speed fit fitting, how they work, how to fit and install pushfit fittings and how to use them on copper pipe.
• Plumbing / heating
Editing software i use www.tubebuddy.com/pricing?a=f...
🧰 The tools and equipment I use www.amazon.co.uk/shop/fixitwi...
John Guest Speedfit 15BPB-25C 15mm x 25mtr Coil amzn.to/3Xv4NOo
JG Speedfit STS15P Superseal Inserts 15mm Pack of 10 amzn.to/3VTtjYg
JOHN GUEST - 15mm PIPE INSERT - Pipe Inserts amzn.to/3VUuCX4
John Guest SpeedFit 15mm Elbow - PEM0315W amzn.to/4c2M8Ol
John Guest SpeedFit 15mm Straight Connector - PEM0415W amzn.to/3XzZFsd
John Guest Speedfit PSE4615W 15 mm Stop End amzn.to/45Ar6nK
The Amazon links above are affiliate links. It doesn't cost you anything to click on them but I do earn a small commission if you do. As an Amazon Associate I earn from qualifying purchases.
00:00 Introduction
00:46 What is inside a push fit fitting
01:46 Copper or Push fit fittings
02:56 John Guest or Hep2o
04:04 How to use push fit fittings and PEX barrier pipe
05:28 BONUS SECTION
05:52 How to use push fit with copper pipe
06:58 How to cap off pipes
07:40 Use with compression fittings
#plumbing #pushfit #
uppbeat.io/t/soundroll/tropicana
License code: CFJARAREXDLYHXWA

Пікірлер: 20

@Simon-fk7mr 4 ай бұрын

Briiliant video, very informative as ever. love your hoola hooping 🤪🤪

@FixitwithFowler 4 ай бұрын

Thanks for your comment! Hopefully, my hoola hooping skills are not wasted 🤣🤣!

@rexlex7784 4 ай бұрын

Fowler’s the main man. This info should be compulsory teaching at school.

@FixitwithFowler 4 ай бұрын

Ha, I wish I was the main man! Thanks for your comment 👍

@pakijetli 4 ай бұрын

This stuff is underrated I think because there's a lot of misconceptions about it

@FixitwithFowler 4 ай бұрын

I agree, it's widely used in new builds and has been for years. Everything has its place, but this is ideal for DIY plumbing. Thanks for your comment 👍

@BobBenz55 4 ай бұрын

Love JG speed fit. So easy to use👍🏼👌

@FixitwithFowler 4 ай бұрын

Yeah they are so easy and with the superseal inserts I think they are market leaders.

@suefowler8005 4 ай бұрын

Hi Steve that's great advice xx

@DingleyDell 4 ай бұрын

Very good video. When you say there is a lifetime, why is that, do the metal grips in the pipe corrode, or does the plastic material begin to perish or something like that?

@FixitwithFowler 4 ай бұрын

I think it's the rubber o ring that will eventually fail.

@LS-td3dz 4 ай бұрын

These use the same edpm o rings as pressfit do, if plumbers are widely using press fit fittings I would expect John guest and hep20 to last well beyond the guarantee. I used to work in maintenance engineering and most of the pneumatic fittings were john guest push fit. They never really gave any problems.

@FixitwithFowler 4 ай бұрын

That's good to know, thanks for your comment 👍

@forced-induction 2 ай бұрын

Insert without O ring (non super seal) is to be used with compression fittings

@FixitwithFowler 2 ай бұрын

Thanks for the info!

@forced-induction 2 ай бұрын

@FixitwithFowler oh I'm not a plumber but just observed that may be a possibility. What you reckon? Or you could have cut a little bit of the cistern away to get angled fitting out and install new one with bigger washer if needed. If the water ever got that high it gonna leak out top anyways.