How to Install a Strap Boss | Connect Waste to Soil Pipe

Рет қаралды 37,448

3 жыл бұрын

Welcome to my tutorial on how to fit a strap boss to a soil pipe. I will guide you step by step how to connect a waste pipe to a stack or soil pipe. If you like the content leave a like and please subscribe for more content like this as I've got a lot more to come and there will be something that will help you out.
Links to the parts i recommend below.
Holesaw and Arbour - amzn.to/2UqW5lV
Floplast Strap Boss - amzn.to/3ynUzPY
Solvent Weld - amzn.to/3jWptea
► BECOME A MEMBER OF THE DIY CLUB Click! 👇🏼
/ thediyguy1
► Get FULL access to the Discord Group and other perks!
Follow me on Instagram 👉 the_diy_guy_youtube
Thanks for watching The DIY Guy. My mission is to bring you the best Tips, Tutorials and Tools to help you learn and save money.
Please be advised that this is only a guide which is intended for informational, educational and entertainment purposes and The DIY Guy cannot accept responsibility for any work undertaken. Be safe and have fun! The DIY Guy may earn affiliate commission if you purchase via the recommended links. These links will not cost you any extra.

Пікірлер: 40

@mikecoslett4439 Ай бұрын

As always. Precise and clear. Exactly what you need to do and no pointless twaddle. Short,sweet and spot on.

@TheDIYGuy1 Ай бұрын

Thanks 👍

@christopherbovingdon6567 7 ай бұрын

Do the soil stack boss 'straps' open wide enough to slide onto the stack pipe? I don't have the luxury of sliding the boss over the end of the stack pipe.

@maryrice2821 3 ай бұрын

Nice and clear demo off upstairs to attempt bath connection to horizontal waste pipe.

@Leeroy0918 Жыл бұрын

Watch this before attempting and it made life easier. Thanks 👍🏻

@TheDIYGuy1 Жыл бұрын

Great 👍

@mikepearson2136 Жыл бұрын

Pure Gold, so glad I found this before tackling a very awkward job. Subscribed immediately.

@TheDIYGuy1 Жыл бұрын

Thanks for subscribing

@antoniogalluccio4213 28 күн бұрын

Where you put the rubber, could you solvent weld as well? And the pipe you put in the rubber is pushfit or solver weld?

@markaitkin7010 3 ай бұрын

Thank you great content helped me a lot sort some pips in the house

@samshinto Жыл бұрын

Very well explained….well done

@TheDIYGuy1 Жыл бұрын

👍

@user-ef9co2zm3s Жыл бұрын

Very helpful Cheers

@mostafaghandehari580 5 ай бұрын

Absolutely nice 👍.

@TheDIYGuy1 5 ай бұрын

Thank you! Cheers!

@dononebullen Жыл бұрын

Great video nice one mate . Electrician doing plumbing that's one job I need to do again! Luckily I didn't glue it first time around

@TheDIYGuy1 Жыл бұрын

Nice one

@scott6530 2 жыл бұрын

Good vid buddy!

@TheDIYGuy1 2 жыл бұрын

Thanks a lot 👍

@prawny12009 10 ай бұрын

Solvent weld needs both pipes to be solvent weldable, not all plastic water pipe is the same.

@johnleeming440 5 ай бұрын

Brilliantly explained. However, we are re arranging our kitchen which means the soil stack entry will only be a meter from our sink is it ok to be that close? I'm just wondering in case of any stench back flow. I'm guessing the water trap will prevent this bit just checking before I go about it. Thank you for this, I am a follower as of today👍

@motbird 2 жыл бұрын

Hi. Can you use a strap boss on the pan connector that comes off the back of the toilet?

@darrenbaker Жыл бұрын

Would this be suitable once fitted, to be installed under a tiled floor? I need to move a sink waste - which currently runs directly straight down into the top hole of a 110mm soil stack (with a cap that has a 32mm hole). Which is in a concrete floor. I need to run/move the waste 30cm to the side (into a corner, for corner unit). So can I channel into the concrete floor and run the 32mm pipe into the side of the soil stack using one of these, and then concrete back over the pipe/channel?

@steves1460 3 ай бұрын

I wonder if it is safe to assume that the type of plastic used on the soil pipe is solvent weldable? Obviously in some situations that might not be enough of the pipe exposed to see any markings.