Changing Potentiometer FIX STICK DRIFT For Console Controller PS5 / Xbox

Рет қаралды 136,757

Жыл бұрын

This controller has a stick drift for the PS5 DualSense Controller. I will try to find out the best solution to fix this drag on this stick. By cleaning the analog stick module potentiometer and wipers. To soldering and replacing the potentiometer on this playstation 5 controller to fix stick drift. If you cleaned the analog module and it still drifting. Your next step is to replace the potentiometer by de soldering and soldering the new one. All the links in this video are below. This method works both for the PS4 and PS5 and Also XBOX controllers since they all use the same Analog module Cubes. Replacing Potentiometer, Drift stick repair.
My Soldering Iron Kit: amzn.to/3liQCrm
Flux Paste Syringe : amzn.to/3N2UfNJ
Soldering Wick amzn.to/3NmJzKd
Analog Joysticks amzn.to/3liR60E
Analog Joystick Replace Kit: amzn.to/3TBBMNz
Potentiometer: amzn.to/3JELv2a
Contact Cleaner BW-100: amzn.to/3HfxMhb:
Tweezers Kit: amzn.to/3VwX52q
Removal Alloy SMD amzn.to/3PrzeOY
Soldering Repair Mat amzn.to/3lhqa1r
Playstation5 Controller amzn.to/39tvQCI
15% OFF KONTROL FREEK WEBSITE: glnk.io/3vlxq/Gamer2Know
#stickdrift #potentiometer #ps5controller

Пікірлер: 240

@ZingiberSnaps Жыл бұрын

That software in the beginning, showing the drift of the analog stick on your laptop screen. What program is that? It looks very useful!

@TheGamer2Know Жыл бұрын

gamepad-tester.com

@hnlgd37 Жыл бұрын

Implementing Hall Effect design/tech joysticks if available, now or later, for example the Switch can be replaced with these. Hopefully they’d be willing to start using this tech instead in the future. otherwise for the time being some of this kind of DIY will have to suffice for now.

@GOATGamerProSticks Жыл бұрын

Notice they put the motor wire solder points right in the centre of the potentiometer solder points to try to stop the use of 3x3mm screw 🪛 actuation recalibration trim pots for your deadspots 🎯 position & max circularity 🕳️ size adjustment of the whole response curve range 😂🤣😭, what total w⚓'s they / them are 🤤🫠😉. I'm onto them these critically thinking 🤔 🧐 eyes 👁️👁️😵‍💫 won't quit 👍🏻🎮🕹️🎯👍🏻 😉 lol. They / them used 2k3 low resistance potentiometers for the same reason, to obfuscate parts selection from the previous generation, but when they go wrong the low resistance pots they go wrong so much more dramatically 🫠🙃🥴 they flip right off there axis ☯️ point 🧭 👀🥹, that's a con-theory well spotted 🧐🔍 there folks & my very own opinion 😬🫡, it's a free public service of mine to turf the build back butter 🧈🫠 🐂💩 where I find it. Sing it with me 🎙️ "Shovel shovel all day long theres another bucket 🪣 of 💩🎮🕹️🗑️ minimum viable disruptive technology" 😜. (The mad hatter 🎩 said it needs more mustard 🍯 spread in it, to many gears ⚙️ that's the problem ⚒️ 👀 don't listen 🦻🏻 to him he's not a watch ⌚ maker everything he says should be taken with a pinch 🤌🏻 of salt 🧂, sorry my creative side just woke up again.) Am I wrong think 🤔 or absolutely spot 🎯 on 🤤, you 🫵🏻 decide lol... Just smile 😁 & nod 🐕🐶 everybody else does 🤷🏼‍♂️🤦🏼‍♂️🙍🏼‍♂️...

@FrozenHaxor Жыл бұрын

@@GOATGamerProSticks The trimmer potentiometer boards are useless, we never used them to begin with because they drastically lower your stick maximum operating area since they offset the potentiometer's hard-left to hard-right movement readings, which will result in some games having broken selection menus and others you will lose full motion speed when panning / moving.

@GOATGamerProSticks Жыл бұрын

@@FrozenHaxor Your doing it wrong, the trick is to use higher resistance main Potentiometer pot sides & see 🥺😳🥹 my extensive works for the correct recalibration 3x3mm trim pot selection values, you have to Taylor the trim pot resistance to the main pots resistance for the max circularity to still reach full 💯%, it can be done & still grant you on the fly screw 🪛 driver recalibration. Trust me on this I've done the home work 📜 lol 😉. I've got XBox one elites series 2 pots in a DS4 via the same resistance recalibration method 🎮🕹️🕹️🎚️🎛️🎯🎯🪛 granting myself stick 🕹️ tension screw driver 🪛 adjustment all at once. There's no way of being modest about it, it's done & done 👍🏻👍🏻😬🤐 why don't anybody believe me 😂🤣😭 lol...

@captainsnake69 Жыл бұрын

"Im no soldering expert" Proceeds to expertly solder the pins

@nakedcutepotato5884 5 ай бұрын

no it wasn't from what I can see it's pretty decent but not "expertly" to say the least.

@Dmwntkp99 4 ай бұрын

Expert is the guy who fixes GPU's for a living, watch his channel he's amazing. I'm no expert either but installed 15 micro switches & scroll wheels on mice so far, you get tidier and organized when getting more experience.

@iosif4619 Жыл бұрын

Cheers for that! I changed the potentiometer and it fixed the drag, but the stick wasn’t moving smoothly. Ended up changing the hole analog module(which was my first intuition), took me about an hour, I hadn’t touched a soldering iron since shop-class. Bought a basic soldering kit and the modules for 20£ off amazon.

@BenFoilHat Жыл бұрын

First video out of at least 15 stick drift videos I’ve watched that showed how to determine if the track was faulty. Thanks!

@mcbprimero 11 ай бұрын

Thanks, easier than replacing the entire analog stick. Now it works like a charm

@jrrlaw 9 ай бұрын

Thank you so much! Opened both potentiometer tabs and blew compressed air inside of the and problem solved. No more stick drift.🎉

@justinrosa5423 Жыл бұрын

Dude this was great help!!! And as a fellow gamer, you make us proud! Putting in my order so I can learn! Again thanks a million dude!

@nickhosford7801 9 ай бұрын

This was perfect! Thank you! I tried the reset, tried the firmware update, even mailed it back to Sony (didn't work). Just had to clean the crud inside the potentiometer and I have my controller back!

@jamesili5672 Жыл бұрын

Very good video, I had problem with ps5 left analog (very annoying drifting backwards) now it is 100% fixed ( non solder method ). Thank you.

@Truemotu Жыл бұрын

Thanks for the video I was about to do the soldering part with my controller but I needed to see someone doing it to get the idea looks easy not that it is but I am more confident that I can do it I don't have nothing to lose trying because I have already a new one and if I do it right who knows maybe I start repairing for more gamers like us 😂

@Melchian1 3 ай бұрын

hey man, i was about to buy new joystick replacement until i saw this video and replaced the original wiper with one from an old PS4 controller and it worked perfectly, thanks!

@4dayyys Жыл бұрын

Thanks to this video I manage to fix my old PS5 controller. 👌🏾👍🏾

@rpaip 3 ай бұрын

Great idea to swap out just the potentiometer instead of the whole joystick module. Can do this twice with one new module. Thank you for sharing this.

@dmc4ever7 Жыл бұрын

This is so helpful and so ASMR 😅. Thank you very much indeed!

@solomagic1591 2 ай бұрын

Best tutorial I've found so far, thanks dude!

@IceYetiWins Жыл бұрын

Thanks so much! The second method worked great on my xbox controller.

@johng6758 Жыл бұрын

Thank you so much ,for taking your time to post this video

@morphixxx2656 11 ай бұрын

Wow works like magic, thank you Brav

@PawnScript 3 ай бұрын

Thank you! I was so close to buying the DualSense Edge until I saw this video. All I needed to do was clean my Dualsense wipers and the drift is fixed :D

@Bekon241 2 ай бұрын

Dont bay edge also have seme potentiometr and same problem not spend money for another trash quality from sony, my 18 years dual shock from psx still work 0 problem with analog... Now all electronic is just junk...

@danig5130 Жыл бұрын

Thank you so much for providing this guide and tools

@m4st4Xk1ll4h Жыл бұрын

Great video exactly what I needed thank you

@arinzechukwuka6122 11 ай бұрын

Excellent work man. You're the best 👍🏽

@Pete217 Жыл бұрын

Thank you so much for this amazing video, very well made. Subbed!

@starnite_47 8 ай бұрын

I was looking on Amazon for a soldering kit today and was wondering what that mesh wire was for 😂 thanks! I'm going to Gamestop to replace my controller under warranty but i also found my original ps5 controller today so i decided to see why i had it stashed. Has drift on right thumbstick going left. If I can find the potentiameter I'll replace that myself. Thanks for showing us the steps 👍 Earned my sub!

@Ice_2192 8 ай бұрын

Thanks for showing this. I don’t have the “idle” drift that people have. I have more of a tilt drift meaning when I tilt my left stick up, according to controller test in astrobot, it shakes up and down. Was debating of changing the whole module when I could just change the part of the module that controls the up and down potentiometer. Really hope someone makes regular controller hall sticks.

@furtalance_x 6 ай бұрын

This was excellent man.

@constantin2152 Жыл бұрын

Thank You Man,you are the best !!!

@gottosahani7571 11 ай бұрын

Thanks for the video It was very helpful

@yourdoomsday1146 Ай бұрын

Damn....thanks man learned a lot, now its time for practical👍🏼👍🏼

@randumdude5824 5 ай бұрын

The discoloration in potentiometer is the wearing of the wiper tines that are on that white piece . I just took mine apart. To find that those tines had worn away and broke off. Scratching the black areas through to copper just underneath that black coat. I think as long as the potentiometer black surfaces are not warn through like this guys is your safe just swapping the white piece, but If the potentiometer side is showing wearing and metal is visible then the potentiometer needs to be replaced. Also you need a magnifying glass to see the tines on the white piece you see how warn they are. That piece is the weakest link in the whole system

@michaelc5373 Жыл бұрын

I've got a controller that's out of warranty anyway, so I've got nothing to lose but time and maybe some solder. Thanks for the vid man, I'll let you know if I'm successful or not

@Rem694u2 Жыл бұрын

Any luck? :)

@michaelc5373 Жыл бұрын

@@Rem694u2 lmao nah, I screwed up my controller 😂 But it was definitely worth a try, and now I have a controller I can practice on if I ever decide to try again

@Rem694u2 Жыл бұрын

@@michaelc5373 Yeah, you had nothing to lose but experience.

@davidtsmith33 Жыл бұрын

Nice tut man.

@cc7 Жыл бұрын

i’m so happy thank you it worked ❤

@TheGamer2Know Жыл бұрын

Im happy it worked for you! :)

@junhyeoklee314 Жыл бұрын

i fixed my xbox one controller left stick drift Thx! (verical drift and clean sensor )

@jasephase2k933 Жыл бұрын

Deserve a sub thankz

@leonardjohnson1333 Жыл бұрын

Amazing video

@wavyyone Жыл бұрын

That was some what stressful, but this video helped a lot. What Sony did with the ps5 controllers is just nonsense, everyone having the same problem with the same stick I was definitely not going to buy new controllers(yep both had the same problem) I’ll fix the other controller tomorrow this procedure really took a lot out of me trying not to damage anything in the process

@deepstructure Ай бұрын

Great guide for disassembling a controller. I will point out for us complete noobs that @2:05 there's a cut and he says "now we just take the motherboard and flip it to the other side..." but what wasn't shown was that there is another ribbon cable to detach at the top right of the board (next to the USB-C connector), before you can flip the board over.

@Barbaros-ux4yc Жыл бұрын

Great video

@RipLagger 5 ай бұрын

Drift happen after i plug the controller to phone charger, fastcharge one, im not sure whether or not it causing burn or something that left debri on the analog module. cleaning the potentiometer and wiper do works! thank you!

@Th3Abyss Жыл бұрын

PHEW! Something I can do. Thanks.

@christorres9833 3 ай бұрын

Thank you this help me.

@CoolSaver 7 ай бұрын

Thanks, i broke dead two controllers, but at least drift issue was solved UPD. I replaced some parts from one controller to another and now have at least one fully working (without drifting). And by the way, for the third one i decided to not open him and just used contact cleaner and dust blower on the stick gaps, it worked as well. But the third one has a smaller drift issue, still, as i said, it worked, it has no drift issue at all now, and I didn't break anything with that one. Hooray 😂 THANKS MAN, REALLY!

@Shade_Rock 6 ай бұрын

This video was a big help, but after watching it in its entirety there is one key detail to note when you put the wipers back inside the potentiometers. MAKE SURE THOSE RINGS ARE NOT UPSIDE DOWN when you put the new ones in. There are two sets of white dots, one close one wide that act as indicators on how they should be placed back into the potentiometer casing. The wide spaced dots should be facing up and the small spaced dots should be facing down. otherwise you will mess up your deadzone reading and make the drift worse till you mount the wipers back in the right way.

@user-cn4ey8km2v Жыл бұрын

Thanks it works big time. The little gadget cost way too cheap compare to getting a new controller. Just replace the potential meter ring as compared to soldering for an entire new one, soldering requires too in depth skills, 😂 power video and guide, 👍💪

@MrRu13s Жыл бұрын

yep. replacing just the little metal ring inside of the potentiometer accomplishes the same thing without needing to solder anything. solid video regardless!

@capitalr8649 Жыл бұрын

@@MrRu13s meter ring?? Are you referring to the track?

@MrRu13s Жыл бұрын

@@capitalr8649 it's apparently called a wiper. it's the only metal piece inside of the potentiometer. it's attached to that white plastic piece. replacing that white plastic piece w/ the attached wiper will accomplish the same thing that replacing the whole potentiometer does.

@MrRu13s Жыл бұрын

@@capitalr8649 I didn't need to do anything to the track to fix my stick drift.

@capitalr8649 Жыл бұрын

@@MrRu13s ok thanks. Bout to order now!!

@RomanoPRODUCTION Жыл бұрын

good job. Just change your rosin which burns too easily or lower the temperature of the tip :)

@itzchris5555 Жыл бұрын

Yeah I don’t trust myself doing this method😂The first method seems pretty easy so I’ll try that one

@iKevinF Жыл бұрын

I’m starting to have some serious drift issues in mine, this video helped me a lot! I’m going to grab some extra modules and try to replace them just like you. Subbed 👍🏻

@iKevinF Жыл бұрын

@samuraiman7777 I did manage to fix the drift but a new problem came up, I think something is either broken or stuck under the inside of the stick, the analog doesn’t re-center itself well when pressed up and to the right. It kind of sticks, but with some assistance, it goes back to center. But yeah the drift is completely gone otherwise.

@iKevinF Жыл бұрын

@samuraiman7777 Yeah the other issue is a bit tougher, I’ll need to completely de-solder the entire module to see what’s wrong. Worst comes to worst, I’ll have to buy a new module, but that’ll come later on. For the time being, I bought one of the all-black controllers so I can still game with a proper controller.

@Raptchur Жыл бұрын

@PogChamp! I feel the same way about beyond my expertise. But it wasn't bad at all. I cleaned it with isoproplyl 91% alcohol and a q-tip and so far it went from nearly unplayable to un-noticeable. $70 is a new game. These things shouldn't break this easy. Imo they are designed to. They want you to have to buy a new one. Again and again. Sony probably hates these videos. I don't understand what you have to lose? I was ready to buy a new one but figured i might as well try this first. If i screw up the controller, it'd be screwing up an already screwed up controller. Now i'll buy a game with that money.

@grimhunter2223 Жыл бұрын

@PogChamp! U can buy a ribbon connector. Just practice on that broken so u have experience once your new controller starts having issues.

@hnlgd37 Жыл бұрын

Implementing Hall Effect design/tech joysticks if available, now or later, for example the Switch can be replaced with these.

@wedemboyz807 Жыл бұрын

Really needed this because mine didn’t last a yr before this started. Thanks a lot

@drifta1167 Жыл бұрын

Thanks for the video, Good job....has the controller played up since doing this?

@m5_sheep510 Жыл бұрын

If you want to, you can use a stick drift kit, yes they’re like $20 but over time, the other parts may give in, with the kit you can easily unscrew and adjust and calibrate it and bam, all done won’t have to do the whole process again

@ryanlin4827 Жыл бұрын

a lot of my friends are having this issue with their controllers. i'll be sharing this vid to them hopefully this helps them repair their controllers.

@csgoinsaneclutches5317 8 ай бұрын

Thank you very much for the video, can I ask you a question? When analog is not centered, its not drifting, just its little bit to the left/right/up/down, so its not centered, shoulg i change whole analoge, or only these potentiometer which its leaning more up/down or left/right

@BenFoilHat Жыл бұрын

What is the difference between the white potentiometer sensor and the black one? I have a rig nacon revolution x that had stick drift. I used a sensor from an Xbox s controller(2022) I never used in attempt to fix it. The sensor didn’t snap into place and seemed like the mechanical movement wasn’t the same as the original white sensor that was in the nacon, like it wasn’t in perfect tandem. When I tried it out, the up and down axis wasn’t even functioning. Just pointing down. After I saw this video I cleaned the potentiometer track and reinstalled the original sensor and it fixed it.

@shabzone Жыл бұрын

Thanks for the video I will be giving this a shot. Has anyone ever tried to put in some sort of lube in the tracks to improve them?

@TheGamer2Know Жыл бұрын

WD 40 is good solution

@chunlimon7862 Жыл бұрын

love the video, step by step ! in the video you have some tool i dont't familiated with, like the yellowish glue thing & the yellow copper like strip, can i have the name what it is called i can order from amazon? thanks

@TheGamer2Know Жыл бұрын

I think you may be talking about the flaux paste syringe and soldering wick. The links for all The stuff in the video is in the description

@ricardofranco4114 7 ай бұрын

I replaced the little metal thing inside the potentiometer and it made things slightly better, but it made it worst while moving up and left.. i took the metal thing out, looked inside the green housing and noticed that the black outer ring is scratched up really badly ! I am going see if i can de solder the green housing and replace it with a brand new one.

@geoffreysweetser3084 Жыл бұрын

Where can I get the new parts ? Last video you said they were cheap 10 for 15 $ I believe ?

@icymichael966 3 ай бұрын

What’s the brush you use for cleaning the melted solder?

@daviemaxed6201 10 ай бұрын

I know this video is 8 months I got 2 pads woth my ps5 when I went to use the second I pulled the left stick up and with only 30 mins of play it'likr stick drift could it be great vid big thanks

@7vanzzy7 11 ай бұрын

Soldered on a new pad and replaced wiper but still has constant drift to the left... I just give up at this point. Thank you for the video though as I'm sure it works for most.

@TheGamer2Know 11 ай бұрын

Sorry to hear it dude, I had a controller also whatever I tried it never got fixed

@youseffaisal4181 Жыл бұрын

Good stuff but a heat gun works best these small heat guns

@Awayze 2 ай бұрын

I’ll solder the new potentiometer on mine. I feel replacing one part only will cause the drift to come back quick. If I mess up, not bothered as the controllers unusable and out of warranty anyway and will be a solder learning experience. Edit: I followed and the black part is hard to get of, plus once I got in I bent the potentiometer piece too much trying to pry it only a little.

@angusfuzz 6 ай бұрын

Hey, how does one unscrew themself once the tracks/contacts are messed up? Give sony more money?

@bkid1776 5 ай бұрын

@Gamer2Know what’s the fix if the holes get burned the metal part and the flux sticks to the board. I tried cleaning it with rubbing alcohol and it wont fully clean it. Theres no metal around the holes anymore does that mean it’s ruined. The potentiometer wont solder to the pcb. Only one of them I got the whole new analog stick in. But 3 holes wont solder. Do i need a new board and where can I get one? Or can I use the drift fix kit and try to solder the potentiometer in using that

@netomanzzi-qq1hb 5 ай бұрын

Estação de ar quente fica bem mais top nesse caso

@elopers6424 Жыл бұрын

great video! what software did you use to edit this?

@TheGamer2Know Жыл бұрын

FinalCut

@bkid1776 5 ай бұрын

Can you burn the pcb hole to the point that it’s ruined I took mine out perfectly surprisingly but some of the holes are more brown when the other holes are clear bright sliver and open

@samherrick15 Жыл бұрын

Yesterday I successfully deconstructed my Scuff Reflex thanks to this video! My left analog stick has some bad drift. When I got to the potentiometer though the green caps wouldn't budge. I used a small flat screwdriver for about 15 minutes trying to get it off. It seems like it might be bonded by an adhesive? Do you have any tips for how to remove it?

@TheGamer2Know Жыл бұрын

They should easy come off with a flat head with enough pressure. I've never messed around with a SCUF, I'm not sure if they are using the same type of potentiometers

@b4gged651 Жыл бұрын

I took apart a buddies scuff to fix a ribbon cable completely unrelated to stick drift but when i was looking around i noticed what looked like to be a dab of adhesive on the cap for the potentiometer curious if this is a common scuff thing as i have also never seen that or taken one apart before

@xljx8304 5 ай бұрын

May i ask whats the settings of watts or heat to this?

@motorbreathjz 11 ай бұрын

what are the numbers on the analog part of it? i found some ALPS 2.1k on ebay but the number on the side is 33 18.. what does that mean? i wanna beable to just use 1 potentiometer for my horizontal drift but if 33 18 is a substantial difference than the oem number then i dont wanna do it all for nothing

@andrewroman4982 5 ай бұрын

Do you know if the wiper is what's wearing out faster or the resistor ring? Have you done multiple of these repairs? Great video, by the way. Compared to most others, which literally just take the cover off and q tip the top of the module, which in fact does nothing because the problem is much deeper. I have this issue on a series x controller, and, more recently, my xbox One elite controller has started to do the same thing. I blame my kids and their grubby fingers. I just got a new controller, but I think I'll give this a shot

@TheGamer2Know 5 ай бұрын

Check my channel for Xbox controller repair. From my experience Changning the wiper and cleaning fixes the problem. If not then the potentiometer needs to be replaced

@andrewroman4982 5 ай бұрын

@@TheGamer2Know can you only get the wipers with the whole set of modules? Buy the modules and strip them for the wipers?

@TheGamer2Know 5 ай бұрын

yea@@andrewroman4982

@bornwisedistruction 7 ай бұрын

Im just glad Sony in their infinite wisdom didn't decide to go with multiple different size security bits in the controller!

@JoshHanma Жыл бұрын

I can’t be the only person struggling to get the green things off. Literally the last step and I can figure out how to open it

@Dzujin 8 ай бұрын

Yes I'm struggle too

@Goku-pm5kg 8 ай бұрын

Do I need to solder it for it to work?

@ItsJustStitches Ай бұрын

FOR NOVICES LIKE MYSELF Just gonna let y'all know now. I had some jittery stick drift (IFYKYK AND ITS FUCKING ANNOYING) I got to the P meter and swapped out the white piece with the gold ring with another white piece with a gold ring from another controller and it 100% fixed my problem. You DONT need to clean the Green Circle. I self taught how to take apart my controller by watching videos and doing it numerous times. It gets easier guys and you get less scared of breaking shit lol. Hope this helps y'all. :)

@jessy1652 5 ай бұрын

After taking it apart and putting it back together my left stick moves clunky do you know what that is ?

@varietas634 7 ай бұрын

my analog left stick feels loose now, is it because of the same problem? thank you

@sleepynik9 5 ай бұрын

What happens if you did separate the potentiometer from the board? I accidentally separated mine when I tried to lock after cleaning..

@bkid1776 5 ай бұрын

@Gamer2Know what are the black and red wires for? if u break the end of it can you use wire cutters to help fix that and then solder the wires back. DO you need the black and red wires?

@TheGamer2Know 5 ай бұрын

I believe they are for trigger buttons and motors connected to the motherboard. You can remove them and then solder back which I did in the video when taking off the MB

@bkid1776 5 ай бұрын

@@TheGamer2Know ok nd what temp should I use the heat gun on Fahrenheit for the desolder I was gonna heat it up then solder suck the solder out

@sonson8335 2 ай бұрын

just wondering what if i replace the potentio to a different value?

@cmor835 2 ай бұрын

hey Bro im about to do the same, i will my vid to yours as a proof of legitimacy!

@user-yd9bp3hk2n 2 ай бұрын

Hello, how many degrees soldering iron did you use?

@TheGamer2Know 2 ай бұрын

700f

@skorch_styptic6550 11 ай бұрын

Fyi- you don't need to remove the ribbon cables from both sides, ones connecting to the motherboard should be enough to get the motherboard out the chassy.

@honorb4glory606 Жыл бұрын

I tried cleaning my vertical potentiometer, and it worked well for a couple weeks. Now cleaning doesn't help, so I replaced the entire potentiometer. Now it pulls down when the stick moves right or left, which is puzzling. Any ideas? Any chance I failed to make a solder connection on one of the three pins?

@Nick-qn5nf Жыл бұрын

Ever figure out your issue?

@koopatroopa1478 Жыл бұрын

I understand that the housing around the potentiometer gets dirty and causes problems, but every youtuber fails to show the actual potentiometer itself. The small plastic piece inside with the little c shaped aluminum pieces attached to it gets bent and corroded which is the main problem. If someone can show me a good picture of where those c shaped pieces are suppose to be by default that would be very helpfull.

@callumyt69 Жыл бұрын

👌🏻

@Glxy_tt 11 ай бұрын

I cleaned the potentiometer and put them back in but now my left analog stick is stuck pointing up whenever I hook it up to the game pad tester and I don’t know why

@Heatlink1 3 ай бұрын

I changed the entired Joystick, but now it won't connect to my Ps5, well it does, but it seems the Bluetooth signal is very poor, I have to stand really close to my PS5 to be able to be recognized, do you know where the Bluetooth traces are on the board?

@FPScustom Жыл бұрын

can you show how you recalibrated the sticks. i soldered a new thumbstick mechanism onto my ps5 controller but having trouble recalibrating. please help :(

@weedless9531 3 ай бұрын

Did you find a way to recalibrate them? I'm having same issue

@jaychaka33 5 ай бұрын

I changed the right stick and now my sons r1 button moves the screen and says controller disconnected when he presses it any help

@Heatlink1 5 ай бұрын

Hello!, I tried changing the entire Analog stick, for some reason the controller still drifts, I removed the Analog stick, turn it back on, and Its magically drifting!, so it was never the potentiometer. Do you have any clue of what have happened? I cleaned every trace with soldering wick, there are no parts connected between them...I wonder.

@Luigi777888 5 ай бұрын

What are the white pieces inside the potentiometers? May need to replace the whole thing, but i need this part

@icymichael966 4 ай бұрын

Wipers

@christopherreynolds7032 9 ай бұрын

Cheers bro

@mcfriedchicken1972 10 ай бұрын

I’ve done this twice now and once to the DualShock 4 and every time the stick drift is completely gone but the joystick isn’t as responsive. I have to move the stick more to register the input. What am I doing wrong?

@mcfriedchicken1972 10 ай бұрын

I’m talking about soldering btw. Cleaning the sensors alone only works for like a week or two before the drift gets worse than before

@Hwa_206 Ай бұрын

How do i know which potentiometer size I need?

@Truemotu Жыл бұрын

What temperature of heat you put on that soldering?

@OriginalSirSpeaksAlot Жыл бұрын

It would have to be around 360°F for it to melt

@paintrax8249 Жыл бұрын

Hello, my potentiometer looks the same as yours. Very worn even though the controller is 2 months old. I cleaned it thoroughly but still the same problem. My stick also moves to the left. Do you think BW 100 will solve the problem or do I need to replace the potentiometer?

@vipset87 3 ай бұрын

Same here!! Only 2 and half months old. What did you do? I dont have money for a new one

@paintrax8249 3 ай бұрын

@@vipset87 Hello, I changed my potentiometer. BW 100 didn't solved the problem for me. The soldering part is not that hard if you take your time and do it step by step. Cost me about 40€ for everything but now I can change them forever on my own

@ALRIGHTMEN-official Ай бұрын

What if you just buy the white thing from inside and put the new one inside so I don’t have to do all that work ?

@calvin659 Жыл бұрын

Thank god, I was able to clean off a surprising amount of dirt/dust from the vleft-vertical pot. Soldering is easy but desoldering is a real pain without an electric desoldering pump. Edit: The wiper fix failed a few hours after my initial post. I used multiple wiper replacements and they all failed so the carbon track needs to go. 😢 I ordered a desoldering iron so I don’t rip out the soldering pads again (RIP Xbox One controller).