HOW TO Hack An Empty Aerosol Can To Make A Free DIY Refillable Compressed Air Duster

Рет қаралды 6,740,926

6 жыл бұрын

Air is free! So why would you spend money buying it in an aerosol, while you can simply make your own DIY refillable compressed air duster!
► YOU WILL NEED
- Empty aerosol can
- A bicycle tire valve (I'm using a valve type "Woods/Dunlop")
- Drill
- Filler metal
- Flux
- Source of heat (I'm using here a Chef torch)
- Hot water for final quenching/cleaning
► DISCLAIMER
Always make sure you operate in a safe and secure manner.
For this project this means, make sure to pressurize the container to a level that is safe and compatible with the max supported strength of the metal joint and of the used container. Failure to do not so may results in serious injuries.
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
► SUBSCRIBE (weekly content)! bit.ly/SubscribeTheLabOtomy
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
► CATCHUP! All Videos bit.ly/AllTheLabOtomy
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
▼ CONNECT!
► Facebook: bit.ly/CauseIHaveNoFriends
► Google+: bit.ly/WhoUsesGooglePlus
► Twitter: bit.ly/LikeASheep
► Instagram: bit.ly/NarcissisticByNature
► Tumblr: bit.ly/AnotherCatGif
► Pinterest: bit.ly/SniffDaMoodBoard
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
▼ MUSIC
► "In The Quarter" by John Deley
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
╔══╦╗╔╦═╦╗╔═╦╗╔═╦══╦═╦╗╔╦╗╔╗
╚╗╔╣╚╝║═╣║║═║╚╣║╠╗╔╣║║╚╝╠╗╔╝
═║║║╔╗║═╣╚╣╦║║║║║║║║║║╠╣║║║═
═╚╝╚╝╚╩═╩═╩╩╩═╩═╝╚╝╚═╩╝╚╝╚╝═

Пікірлер: 1 100

@wonderwood1967 2 жыл бұрын

Room air is not dry. The moist air is not a great idea for cleaning electronics, but for blowing general dust and debris, this definitely is a keeper

@luisp1174 2 жыл бұрын

That looks like a easy to do fix for out of air issues, I’ll have give it a try and see. Thanks for sharing

@19dfr54 5 жыл бұрын

Much easier to remover diffuser at the top. Place automotive valve stem over pin and add compressor air. Control pressure with line valve on compressor. Safety issue addressed.

@cowdiologist2759 2 жыл бұрын

I use my rubber tipped air nozzle and add 120 psi, been doing it for years

@Bramble43 2 жыл бұрын

How do you refill the liquid?

@alasdair4161 6 жыл бұрын

Yep, pretty well covered BUT.. a note to: A' confirm the can is empty before drilling.. B. purge explosive gasses from can prior to soldering. C. fill cup around nozzle with water to avoid over heating the plastic valve during soldering. and all is good. PS, most spray cans have a design limit of 100psi, so use caution when filling, a rupture would make for a very bad day at ICU.

@TheLabOtomy 6 жыл бұрын

Good points, thanks for the complementary info

@wangmauler 3 жыл бұрын

@Scio qui sum -Je sais qui je suis I have a cheap Pneumatic air hand pump that goes up to 1,500 psi. Don't listen to scio's info. Anything dealing with compressed anything has a danger.

@Nerino666 2 жыл бұрын

especially when, for example: grinding open an old LPG-tank..., you'll be gled you filled it and rinced it with water, and with a real big tank: keep the walls humid, even steel is porous...

@PoisonShot20 Жыл бұрын

Remember, looking time ago, I was 10, heard of a Mechanic/ Blacksmith got killed, and the whole building, about 12x12, was leveled. He try to weld a empty 50gl drum, that was used to store gasoline, even thought he filled with water, but not to the top. Sad tragedy!

@vicferrmat4492 4 жыл бұрын

Thank you , great idea. This is so beautifully creative, a pleasure to watch. I am inspired.

@russelblackwell6041 4 жыл бұрын

MAN YOUR EASILY IMPRESSED did you have an anxiety attack

@urvidsucks1 3 жыл бұрын

Balls deep,toss his salad while ur at.

@murometz626 3 жыл бұрын

I would tie a short string from the valve to the can body in case it pops out due to too much pressure.

@grauwolf3977 5 жыл бұрын

v roce 1966 , bylo mi 8 let, jsem si tímto způsobem nabarvil rám na kolo! Krásné vzpomínky na vesnici Mokropsy!

@jeffbingaman2754 6 жыл бұрын

Just use an air nozzle with a rubber tip. It will both fit over a stem if the spray nozzle is removed and just hold it against the hole if he nozzle and stem are connected.

@krzysztofczarnecki8238 6 жыл бұрын

This really works and is practical, but don't expect it to last anywhere as long a new compressed "air" can on one inflation. The "air" in new cans is actually any cheap gas that can be compressed until it's liquid in room temperature (usually butane, propane, relatively non-toxic refrigerants are said to be used as well), and air unfortunately can't be, so there is much less of it than weight. If you can only find bike tubes with plastic valves that have metal thread, they can probably also be used, as they are actually brass inside, just scrape off the plastic. Solder holds better if the can and the outside of the valve are brushed with a metal brush. A can inflated to 6 bar is enough to dust a keyboard thoroughly once, and in some other video a guy (kzfaq.info/get/bejne/qLhdhppey6e6hJs.html) inflated a spray paint can to about 15 bars, and the top dome moved out a bit around the rim, but it remained intact until it was inflated to 25 bar, and the bottom lid came off, sending the rest of the can in opposite direction at high speed. But for this you need a good big shop compressor, not the cheapest car tire compressor that also happens to be ten years old.

@ronnieg6358 3 жыл бұрын

Good idea! Depending on the contents of the can the flame could cause an explosion, that would be exciting. A big soldering iron might be safer, you would then have something left in the can to spray!

@jeovannyainstainvelasquez3319 2 жыл бұрын

from Honduras love this music

@rob_erto 2 жыл бұрын

I'm sure the flammable vapors ran away when he drilled a hole in the can😎

@andr59 6 ай бұрын

@@rob_erto Fill at least 80% with water to avoid the problem of explosive gases that may be present

@paulvanos976 2 жыл бұрын

I glued a funnel on the back of a mini vacuumcleaner and the blowingpower is eeeeh... mindblowing. Supereffective, cheap and easy to make.....

@Chris-yy7qc 6 жыл бұрын

This will only hold a very small amount of compressed air, because air cannot be liquified. So you would have to refill it after a few seconds of use. Thats why commercial compressed air cans are filled with lighter gas (butane gas).

@TheLabOtomy 6 жыл бұрын

True

@witboj8281 6 жыл бұрын

No, they are filed simply with CO2

@alanhilder1883 6 жыл бұрын

Air can be liquified.... but not a a pressure that could be contained in anything like that can.

@nicku1 6 жыл бұрын

Air CAN be liquified -two Polish scientists - Olszewski and Wróblewski did it in 1883 at the Jagiellonian University in Cracow.

@richardj2927 5 жыл бұрын

Commercial air cans filled with flammable stuff like butane ? definitely not for sure

@mikaruonala2297 6 жыл бұрын

We have been using empty cans prepared exactly like this in RC planes to operate the landing gear for decades. I fill mine usually up to 5-6 bar. Thus far I never heard of any exploding. On the other hand, RC modelers usually know what they are doing when it comes to soldering and other technical stuff.

@TheLabOtomy 6 жыл бұрын

Thanks Mika for the extra info, did not know of this usage in RC planes so am a little wiser now!

@simonwhite699 2 жыл бұрын

Yes until the 90's when Ii used mechanical servos on my ez suprastar, previously I used Rom Air retracts and never had any problems whatsoever!! :)

@yazzercan4181 5 жыл бұрын

You do know you can refill the can from its original nozzle just remove the spray head and use your compressor to fill it up with air

@RanMinato 3 ай бұрын

🎉😂

@upnorthofcali7399 Ай бұрын

Make a video on how it's done please

@pl5624 3 жыл бұрын

If that pops out you're going to be missing an eye....

@COOL-yx6ih Жыл бұрын

😂😅we be by been

@tonysicily2687 4 ай бұрын

A good point, well worth remembering to point that away from you while you use it, same as with any tool THINK SAFETY. A good point, well raised.

@SureshKumar-nk2ok 5 жыл бұрын

thank u very sir . is it aluminium filler wire ?/

@tanveerkhan9221 5 жыл бұрын

That soldering was really good

@onepercentile 2 жыл бұрын

The drill shards enter the can and then get stuck in the spray head? Might be wise to punch a hole with a super sharp nail if it doesn't deform the surface any for soldering.

@sanikam6079 6 жыл бұрын

this is a great idea. I am sure someone can think of other uses for this method. thx

@vjvivishnu205 5 жыл бұрын

Hi brother your video is very very helpful and easy to understand . Soldering liquid and soldring led where did u buy it? Sir

@davidl5546 2 жыл бұрын

Long, long ago I had thought of doing the exact same project, but I decided not to, when I considered the following: 1. The propellant in a normal spray can is NOT compressed air. Used to be cfc or some other gas which becomes liquid when compressed. During manufacture, the can is filled with the liquid propellant, the liquid to be sprayed, some air space, then the whole thing is sealed up. Some of the liquid propellant becomes gas and builds up pressure. Eventually enough pressure is reached to stop further evaporation. The problem is, what is that pressure, and what is the pressure the can will take before exploding? It may not be as high as you think. So I decided it was too risky to try making. 2. To pump air in to a safe pressure (how much is that?) is good advice. However, unlike the propellant which constantly evaporates to maintain the pressure in the can as you spray, in this diy can with pressurised air, you will very rapidly reach the point where the remaining pressure is not sufficient to be of much use. That is why I decided way back then that it was not advisable to try it. Probably safer to use a Tubed tyre, with a high pressure hose leading from the valve to an air spray gun.

@johnsanchez8029 2 жыл бұрын

Without some sort of activation energy in the presence of a combustible fuel, an explosion from atmospheric air is not possible. This project is missing 2 parts of the fire triangle. So fire is not a concern here. Even when he was soldering. Unless the can wasn’t rinsed. Even then, with that drilled hole, no way enough pressure could build up (during solder).

@davidl5546 2 жыл бұрын

@@johnsanchez8029 didn't mean explosion in the sense of the Fire Triangle. Was thinking of explosion due to too high pressure being pumped in. How high is too high? No one knows as commercial spray cans were never meant to be used for this purpose, so it is very unlikely that the manufacturer would specify what is the max pressure the can is able to withstand.

@k1ortia 4 жыл бұрын

Cool, but how much psi, I'd make one with a pressure valve so i know how much air is one can. Nice vid tho. 👍🏽

@XXIIXIIIXXXIXXXIX 6 жыл бұрын

Luvin that intro, good video!

@TheLabOtomy 6 жыл бұрын

Thanks for the feedback, appreciated

@notforsale1264 3 жыл бұрын

@@TheLabOtomy ,tbh the intro sucks , gave me a wannabe scientist chanell vibe but the content is crab .

@javierv.r.6977 3 жыл бұрын

Excelente! muy fácil y práctico.

@cirwo85 4 жыл бұрын

Can you reply here with the amazon link to the metal filler and flux you are using . Thank you

@LeviBulger Жыл бұрын

It's just solder and solder flux. It honestly doesn't matter much. The only thing that matters is that you completely seal the hole with solder

@cirwo85 Жыл бұрын

@@LeviBulger I see that now. I was new to soldering when left that comment and didn't know what was going on apparently

@LeviBulger Жыл бұрын

@@cirwo85 oh lol, sorry. I thought this video was new honestly. It just showed up in my feed and I didn't even pay attention to the timestamps. Anyway, cheers mate!

@cirwo85 Жыл бұрын

@@LeviBulger nothing to apologize for. Thanks for the tip anyhow. Someone else could use it

@josejose-jw1wy 4 жыл бұрын

aprendi mais uma vez como fazer uma ferramenta vendo seu video gostaria de saber qual acido esta usando para soldar att

@mazman8343 4 жыл бұрын

great video dude what did you use to stick the nozzle with

@vladislavroytapel2830 4 жыл бұрын

please let me know how good pressure and long lasting will it be ....is it compatible with original fill ..comes with chemicals ?

@OrieusNyam 3 жыл бұрын

Excelente! Qual solda vc usou?

@marcinxxx83 2 жыл бұрын

Też jestem ciekawy :)

@mueffe1357 4 жыл бұрын

If you oh so desperate for an expensive can of air. You can use propane can for dusting. Same stuff they use. If safety is your concern and being a cheapskate too. A tire inflated to 40-50 psi with an appropriate attachment would do nice too. I airbrush toys using car tire as an air source. A nice learning experience.

@osmarneves4358 3 жыл бұрын

what materials did you use to make the weld?

@spacedusty 6 жыл бұрын

Filler metal is something that usually used in welding process right?

@midoomirza4009 5 жыл бұрын

What materials do I use in welding?

@IGOPU 2 жыл бұрын

a welder

@onepercentile 2 жыл бұрын

@@IGOPU lol

@jerseyneil1 6 жыл бұрын

Despite all the safety concerns. it is a pretty cool video. Thanks.

@johnmav8309 4 жыл бұрын

Thank you!

@FourSeasonsHD 5 жыл бұрын

Soldering job is flawless and result is beautiful joint.

@TheLabOtomy 4 жыл бұрын

Thanks, not talent, just practice

@FULLCEZAUM 5 жыл бұрын

E se eu colocar tinta esmalte sintético dentro, será q funciona?

@blondisbarrios7454 4 жыл бұрын

What materials did you weld with?

@Baldavier 3 жыл бұрын

Is there any adapter to pump air into the top instead of making a hole? Or could one be made?

@kolerasic924 6 жыл бұрын

Bravo majstore

@TheLabOtomy 6 жыл бұрын

Hvala

@caseyrevoir 4 жыл бұрын

Adding the valve to an empty air duster can would be more effective I would imagine.

@petethewrist 6 жыл бұрын

Might make one that I can fill back up with paint,, Cheap sprayer,, Cheers, Pete

@yuuyuu3333 5 жыл бұрын

Nice to meet you, but I wanted to do it but I wanted to make it. How about using a tubeless valve of a car or a motorcycle by another method?

@Robert_Keel 5 жыл бұрын

You are specifying the joint - what is the max safe pressure?

@j.c.8149 3 жыл бұрын

65 psi is a good preasure for this bottle mod. The limit is over 120 psi. But you must try with security method... Can be dangerous.

@emp29 5 жыл бұрын

Drilling while holding the can, did something similar before and almost punched a hole through my hand.

@paulsuggs 4 жыл бұрын

Same here, pulled muscle tissue out of my hand too

@brianhill1048 Жыл бұрын

Nice! next I'l have to figure out how to reload the can with color medium.... Could of course try to enter it through the same hole. But that hole afterwards is soldered so I would need to perforate ad infinutum to make this a good reusable toy.

@SAHILSHAIKH-lw7nl 6 жыл бұрын

Thank u ... How to fill something inside..?

@Digmen1 6 жыл бұрын

Great video, but you need to tell us what that stuff in the blue can is. And more about the soldering.

@ka-i 3 жыл бұрын

Flux and I assume silver solder

@blutrax 6 жыл бұрын

I've got a hairdryer, it never needs refilled.

@TheLabOtomy 6 жыл бұрын

Living the high life hey....

@inglouriousmofo 4 жыл бұрын

@OK Boomer see your username lol

@LonganLee 4 жыл бұрын

Very useful tips and effort in making the demo! What is the solder used? Regular circuit board solder?

@edcrabb 2 жыл бұрын

No to bond metal on metal you use flux and 60/40 solder. 60% tin, and 40% lead. Electronics solder uses a flux core solder. This is a different type of solder and does not create the proper bonding of metal on metal, It is used to bond a copper, brass, or gold surface to a tined PC board surface.

@trongmanh01 5 жыл бұрын

What did you using to weld ?

@runstreetsofvegas 5 жыл бұрын

Impressive I thought you was going to epoxy it. I was like wtf. Looked again and seen solder.

@SoSo-vm3jd 4 жыл бұрын

ผูที่

@SoSo-vm3jd 4 жыл бұрын

ย้อๆ

@GeorgeGeorge-xj2bc 6 жыл бұрын

Can the overpressurized air cause a hurricane?

@TheLabOtomy 6 жыл бұрын

It has also been known to start a revolution in El Salvador, so most definitely!

@kassemsalloum6064 3 жыл бұрын

Hi , what is the substance u put before soldering the valve ? And what is the max pressure we can fill it with ?

@williamgeorgelopezjunior8533 3 жыл бұрын

Kassem Salloum it’s called flux but I don’t think this solder setup will hold for too long. You’re better off probably ...using a tire valve meant for car wheels ... it has a rubber style grommet that grabs the inside of the can ... just my opinion though

@xf9427 5 жыл бұрын

What type of welder did you use?

@penetrus 3 жыл бұрын

Po takim lutowaniu szybko uwie się ten zaworek i trafi w oko.

@dogemaximum4742 6 жыл бұрын

Ok, I understand how to make a compressed air duster, but you still didn't teach me how to hack an empty aerosol can.

@TheLabOtomy 6 жыл бұрын

Busy sharpening the axe...

@dogemaximum4742 6 жыл бұрын

The LabOtomy I meant to hack it like a computer. It was a joke.

@TheLabOtomy 6 жыл бұрын

Hoooo

@TheSatan222 6 жыл бұрын

Doge Maximum you need a special usb

@toxictoxic5454 4 жыл бұрын

@@dogemaximum4742 .

@Spartan_Blades 6 жыл бұрын

how many pressure in? and how I can learn how pressure can we load in that spray? ????

@johnkoury1116 8 ай бұрын

Beautiful!!! I am absolutely going to make a few of these for all my solvents etc...

@johnbanks370 3 жыл бұрын

I was waiting for the can to explode. If it had paint or another flammable in it

@Scanz_99 6 жыл бұрын

what did you use for solder ?

@TheLabOtomy 6 жыл бұрын

Best is to use brazing rods, understand their properties and never over-pressurize the container

@Scanz_99 6 жыл бұрын

thanks

@got2kittys 6 жыл бұрын

matteo scanziani thats a good question. It looks like......solder.

@maritatanner3190 2 жыл бұрын

solder solder

@jansolo55 6 жыл бұрын

You can also do a painting can with this . If you drill a second hole and add a filling cap, with a seal, with the same method . Rinse the can, dry it . Now, you have to fill a half of the can with liquid paint , close the cap and introduce air through the valve, using a compressor , until you reach 6 or 7 bar pressure . And just painting .

@steevo9656 6 жыл бұрын

just add the paint through the valve, re-assemble and pressurize

@jansolo55 6 жыл бұрын

Yes , you're right, but it seems to me that can be difficult to add paint through the little hole of the valve, you don't think ?? And over time, the paint could partially clog the valve ?

@SeekerGoldstone 2 ай бұрын

@@steevo9656 Don't apply fire or heat to a can filled with paint.

@FeeldahVibe1 4 жыл бұрын

How do you get it to spray liquid?

@joelcardosopereira 5 жыл бұрын

Parabéns Presidenta Dilma Rousseff. Já conseguiram estocar ar!

@jamesbarringer980 5 жыл бұрын

Llofd

@ermesonmenezes 4 жыл бұрын

kkkkkkkkkkk

@allef237 4 жыл бұрын

@@ermesonmenezes caralho os mitos estão em todos os lugares kaksdkaskd

@johnsonhenrique2831 4 жыл бұрын

Bom pra estocar peido de cachaceiro!

@linsande 4 жыл бұрын

Ela queria estocar vento 🙄

@user-tq5xk5yu4w 5 жыл бұрын

スプレー缶の再利用は破裂の危険があるからやめた方が良い。

@mintkamagata8949 4 жыл бұрын

チャリ空気入れで金属缶が破裂するほど空気いれられるわけないｗアナルでも平気、コンプレッサは死亡例あるが

@bombblast9668 3 жыл бұрын

Your reconciliation was very good. What did you use for solder in the blue bottle? Please reply with name

@killerjay6755 2 жыл бұрын

its called TIN

@ASHORSHEMAYA 5 жыл бұрын

Hi , can't you put some liquid colors in the Can also so use it like a spray ? try it if you want 👍👌

@amanofmanyparts9120 4 жыл бұрын

Add a second sealable port and you can fill/refill the can with ... whatever.

@thesuperjezz2740 4 жыл бұрын

Spray on lube....

@IhaveCripplingAdhd99 3 жыл бұрын

a man of many parts ahh so your here for the same thing as me

@IhaveCripplingAdhd99 3 жыл бұрын

The Superjezz also a pretty good idea

@daverea372 2 жыл бұрын

Im guessing you could take out the valve with a common tire valve screwdriver, then use a tube or nipple on different squeeze bottle?

@ernestoore1381 5 жыл бұрын

Calentar un en base de aerosol que haya tenido un contenido volátil es muy peligroso, podría explotar

@TheLabOtomy 5 жыл бұрын

Correcto

@sergioferrer202 4 жыл бұрын

Con todo respeto pero creo que es una boludes hacer ese soplador si quieres soplar con el culo lo haces mejor 🤣🤣

@fvrrljr 6 жыл бұрын

Ahhhhh LOL my hat off to you. great Disclaimer yep guilty of safety police but you covered all your bases. I Like, OLE!

@gothikgraphy2042 5 жыл бұрын

super fawsome vid bro, quite inspirational,. what if i drill another hole and attach a sorta able to close valve to add paint or ink to the can,. is it possible u could try it,. the price on cans in my country are way to high plus them health risks are fckin wth my will to live:D

@wagnersantos9617 5 жыл бұрын

E pra colocar a tinta dentro como faz🤔

@andersonbruno7896 2 жыл бұрын

Tira a válvula e coloca pelo bico

@qazmlp2810 5 жыл бұрын

Тормозухи налить, будет вд 40)

@ronmartinmhg2804 3 жыл бұрын

What flux did you use?

@paulsobus6749 6 жыл бұрын

I fill mine with r134a, thru the one way valve on the top of the can. I use it to cool circuit components.

@olgagoyacastro1981 4 жыл бұрын

Pl Pliculavaqueras

@jimchance5006 3 жыл бұрын

Paul Sobus bruh that's actually like really really bad for the environment and super illegal. Not to mention, r134a is toxic.

@Sdelay-Sam777 5 жыл бұрын

I've already done this. A simple lesson ...

@Bhai_From_Bihar 6 ай бұрын

Can I fill it using bicycle pump And how many pumps can I do with it

@dmitrij_nesterov 5 жыл бұрын

Круче аэрозольного аэрозоля может быть только аэрозольный аэрозоль из аэрозоля.

@golibjontolipov8216 5 жыл бұрын

😂😂😂😂😂😂😂😂😂

@BlazeBytez72 2 жыл бұрын

How amazing is that !?!? Well done man 👍

@tippvehler78 4 жыл бұрын

Könnte man auch einen zweiten Stutzen anbringen durch den man z.B. Lack einfüllen kann und das dann sprühen?

@2620044 4 жыл бұрын

持続力2秒くらいかな

@wolflicious8912 6 жыл бұрын

Isn't this dangerous will the can explode under too much pressure?

@TheLabOtomy 6 жыл бұрын

See Description above or Pinned comment

@Quimerateck 6 жыл бұрын

If that was the case, the valve would pop out

@dhanielcuento2535 5 жыл бұрын

Why my valve stem didnt stick on the soldering wire that use? The valve stem that I use is color gold i think something like copper

@skakpedersen 3 жыл бұрын

5.4 million views well earned. Thanks for sharing!

@arnoldsimmons5289 6 жыл бұрын

When I cut paper, I do it over a garbage can.

@TheLabOtomy 6 жыл бұрын

That is a really good thing to do, keep on doing this by all means!

@moacirg 4 жыл бұрын

Aí o moleque faz o negócio desses e tem a "brilhante" ideia de levar ao posto de gasolina mais próximo e dar uma baita carga de ar comprimido no calibrador de pneus. BUUUMMM!

@saxnoobplayer9710 3 жыл бұрын

cool idea man , thanks !

@TheWhitde 11 ай бұрын

I have a heap of compressor gauges and outlets so my plan is... do above with a larger vessel, valve will ensure a pressure limit. Provided I can fill with my air compressor, it has a 3 stage moisture trap... so I can finally de-dust my pc without having to disconnect and take outside.

@rogercamp6071 4 жыл бұрын

I'm surprised that it worked so well,my dad had a similar idea and when trying to solder a fitting to the can the plastic spray nozzle melted,his idea was for making a cheap refillable paint can though.

@nullvoid564 4 жыл бұрын

Probably should have mounted the valve on the bottom or side that way you can keep the plastic parts and nearby metal immersed in water to protect them. though you need to pressurize the paint and it cant be too viscous and if it dries within the nozzle its over

@jean-baptiste6479 4 жыл бұрын

"don't drill even when empty". Drills it.

@persona83 4 жыл бұрын

Because rules are made to be broken.

@saintanthonygoodchild1288 4 жыл бұрын

What will happen? I want to do this but comments are concerning.

@mikevincent6332 4 жыл бұрын

empty means 'empty'

@nastykamaleon472 4 жыл бұрын

Shut a fuck up

@inglouriousmofo 4 жыл бұрын

@@saintanthonygoodchild1288 The can could explode if there's enough pressure

@celiusferreira6130 4 жыл бұрын

Prezado amigo, qual é a marca desse minimaçarico aí?

@adithyanaresh793 3 жыл бұрын

Could you do the same thing but with liquids like say a compressed deodorant spray?

@zelenkin1sergey 5 жыл бұрын

Всё ерунда - такой баллон можно использовать только для сдувания пыли - краску не распылит- краска будет писять струйкой. потому что для краски заправляют специальный газ, который расширяется при распылении.

@zendandrei4286 5 жыл бұрын

А про краску речи вообще не было. Баллон для простого воздуха что бы сдувать пыль например.

@MegaMozart13 5 жыл бұрын

Ты не поверишь! Все газы выходя из баллона при распылении расширяются! А вот в балон закачивают инертные газы, а не воздух, в котором краска сохнет.

@zelenkin1sergey 5 жыл бұрын

@@MegaMozart13 хочешь сказать что если закачат ьв балллон с краской обычный воздух, то он будет распылять краску не хуже инертного газа?

@picancoap 5 жыл бұрын

@@zelenkin1sergey Аэрозольная краска производится с использованием бутанового газа, а не воздуха. Затем краска выходит вместе с расширяющимся газом и переходит в газообразную форму, как только она покидает цилиндр, что способствует более тонкому туману, в противном случае для такой же работы требуется гораздо большее давление.

@zelenkin1sergey 5 жыл бұрын

@@picancoap А я что, что-то другое написал? прочитай мой первый комментарий, под которым ты доебался до меня.

@nappingpup105 6 жыл бұрын

Safety Police Comment: At 0:32 video shows an awl trying to indent a hard curved surface. The action of the awl is directed at the opposing hand. Clearly an opportunity for a slip of the tool to perforate that opposing hand. Take note of shaky herky jerky action at 0:32. Never place yourself in the line of "fire" when using hand tools. Always wear your work gloves.

@TheLabOtomy 6 жыл бұрын

Thanks for intervening, that was clearly an unsafe situation I will reflect upon through my weekly Post Near Miss Review process

@hintzofcolorconcepts 6 жыл бұрын

all this while adding a valve stem to a spray can that could pop off at any time and poke your eye out while filling it, using it, or just sitting there because soldier weakened too much from the pressure.

@whydohandlesexistAAA 6 жыл бұрын

Chris Steele Jerking off and accidentally punching a hole in your hand are a little different, aren't they?