#automotive #welding there are still many who don't know how to weld aluminum using tig argon welding there are still many who don't know how to weld aluminum using tig argon welding
Пікірлер: 581
@user-mg9gw4ir2m Жыл бұрын
После просмотра убедился,что не умеющих сваривать алюминий,стало на одного больше.
@sebastiand.6708 Жыл бұрын
Hahaha😂😂😂
@rus_Dima_H154CK Жыл бұрын
Я даже в хлам пьяный такой шов не смог бы положить 😁.
@REMONTKachyg Жыл бұрын
Солидарен. @TIG TULA Иван бы подзатыльник за такую работу отвесил! :-)
@serg360 Жыл бұрын
И электрод нехера не может заточить правильно😂
@rus_Dima_H154CK Жыл бұрын
@@serg360 ладно заточить, длину в 3мм выставить, на отдельном куске подготовить нужно, чтобы на конце вольфрама отражение своё было видно. Ток настроить по нарастающей за 1-1,5 секунды до рабочей (чтобы не сжигать) и на затухание от двух секунд (как на нержавейку) да газку поддать 😁 Учись студент, мы это горя повидали лет 20 назад 😁
@Abdul_Karim93 Жыл бұрын
А мне бы было стыдно такое на весь мир показывать😂😂😂там на моменте заточки вольфрама стало все понятно😢
@andrzejszczukis6502 Жыл бұрын
Кулибин молодец 🤣🤣🤣🤣🤣
@MrDredio9 ай бұрын
до сих пор не умеет точить), не то что сваривать)
@user-gx8kk4gp3y7 ай бұрын
@@MrDredioда зачем его точить? Один хрен заточка в шарик превратится😂😂😂
@76mrArt7 ай бұрын
Ага, кстати. Не варю аргоном, но даже я знаю, что точить стержень при заточке держат параллельно плоскости вращения диска. И наварить с порами это видимо показатель скила😂
@user-xv4oq7hf5u4 ай бұрын
Плюс ко всему прихватку не поставил, видимо не знает что металл стягивает при нагреве🤦♂️
@nalopakov Жыл бұрын
After I saw how the author sharpens the electrode, I understand that he also does not know how to weld aluminum 😄👍
@georgestiles3500 Жыл бұрын
I also thought the filler metal looked dirty. Didn't see him wipe it down with cleaner
@Bluemoonseal Жыл бұрын
😂😂😂😂
@HVWeight Жыл бұрын
🤣🤣🤣🤣😂😂😂
@briankarnowski5614 Жыл бұрын
Casting WAY too dirty, needs much more cleaning.
@user-dc5sq3dp6t Жыл бұрын
Будто ты умеешь...
@user-ew1ho6km1g Жыл бұрын
Ходят слухи что он до сих пор варит эту крышку
@user-gx8kk4gp3y7 ай бұрын
Это правда😂😂😂 На импульсе Даже сейчас слышу, как варит...
@user-in4or6xj1i2 ай бұрын
Сварил на троечку. Нужно было поставить прихватки. А так левую сторону стянуло по зазору , к бабке не ходи. Нужно было вставить временную вставку в зазор, слева, чтобы прихватками зазор не стянуло. Потом удалить. Вылет вольфрамового электрода нужно делать меньше , да защита аргоном слабая. Всегда нужно по сварочному шву на алюминии и сплавам проходить второй раз, чтобы из шва выгонялись газовые включения, поры. И шов делать более товарным. Всем сварщикам рекомендую книгу, "Электротехника для сварщиков". Чтобы не тупо сваривать, а понимать химико-физические процессы при сварке. Да и теплопроводность металлов нужно знать, как таблицу умножения. То , что выложил, хорошо, есть с чем сравнивать. Дерзайте, мой юный друг!
@uaz_patriot33 Жыл бұрын
После заточки вальфрама и подготовки детали стало понятно что с такими роликами бездарей становится больше. Зачистка внутри детали ступенчатым сверлом 😂😂😂😂
@kioshiro482 Жыл бұрын
An old welding teacher once told me; "welding is not for everybody". This is the video version of that i guess
@robertblackshear89636 ай бұрын
It definitely is. He's got to be kidding.
@issarashid239 Жыл бұрын
This guy inserted the title of the episode on himself. His words are true. Some people do not know how to make a Tig welding, which is the biggest evidence for that. I hope you will come to my country and I will teach you the basics of welding
@Gunnl4 ай бұрын
I am not a welder .. just watching some youtube videos online about it ... can you tell, if he needed it to 'warm up' (not sure if that is the correct term) a bit longer so that pool would reach the other end ?
@dubdzine3 ай бұрын
He is probably already in your country by now, lol
@user-zp4zq7ez9w22 күн бұрын
Меня научи,варю и проволокой и палкой, а этим не пробовал
@bozly2096 ай бұрын
After watching like 30 tig welding videos this one takes the cake.
@Dillon-ux6it Жыл бұрын
Sometimes pre-heating the aluminum helps before TIG welding even if you've cleaned the metal really well beforehand.
@robertblackshear89636 ай бұрын
Exactly. Even with spoolgun.
@stevenconnor42212 ай бұрын
Id say it helps everytime, but unfortunately sometimes its not possible, thats why i always use a foot pedal to control the amperage.
@halledwardbАй бұрын
A button with pressure, or a slider mounted on the Torch handel, or the shoulder works well also.
@alextrofimov62087 ай бұрын
Разделка коническим сверлом, это Шедевр. На AliExpress кончились шарошки?
@Nuclieyeone Жыл бұрын
A how NOT to Tig an engine case should be the title of this.
@stefenmitchell4112 Жыл бұрын
do you have a video on how to do it then
@pxkdin428911 ай бұрын
@@stefenmitchell4112no i guess😅
@zemudikat10 ай бұрын
@@stefenmitchell4112you want to learn from the youtuber so much.. good luck with that 😂😂😂😂
@andreynagorny413710 ай бұрын
Дружище, жаль конечно что еще мало опыта в познаниях и практике. Думаю у тебя еще все впереди. Удачи.
@russellaustin4988 Жыл бұрын
Yes, there are actually billions that can't Tig aluminum...They are not welders. And from the look of that weld, you are one of them
@joken8901 Жыл бұрын
there are many that dont know this and your correct how did you guess he cant weld ...by his flip flops...🤣
@joemestan6526 Жыл бұрын
Yea
@drewrinker2071 Жыл бұрын
Where is your aluminum Tig welding video? Show us how it's done.
@iamisworo Жыл бұрын
Baru mau komen 😂 kegedean amperenya
@scorpioslab Жыл бұрын
You should have did a thin pass a medium pass than over pass that looks horrible
@user-fl5ei4mf9r10 ай бұрын
Прихватки не поставил,из-за этого слабую сторону увело внутрь,ту,которая слева была,электрод сразу же мокнул,в середине сварки видно что он разслоился,из-за того что большую очистку поставил. одни поры в шве,ну и электрод заточил очень плохо.В общем неплохо для самоучки,но такое выкладывать нельзя,даже если тебе угрожают террористы
@fakmak7207 Жыл бұрын
Земеля,я надеюсь ты прикалываешься?))
@alexei0289 ай бұрын
Кто сколько раз насчитал как в ванну электродом въезжал "мастер" ? И далее как ни в чем не бывало.))))
@The1mybuddy1 Жыл бұрын
Title should say. Here's literally everything you should not do when welding aluminum.
@goldmaster3821 Жыл бұрын
Стало меньше тех кто перестал отличать хорошие швы от плохих)
@igorporman66282 ай бұрын
Я плакал от😂 два раза первый когда он снимал кромку, второй когда вольфрам точил... А когда начал варить... Я уссался от смеха.
@anthonysgarage52835 ай бұрын
There are a lot of negative comments on here, just ignore them. I'm no pro but part looks repaired & will probably work fine. keep doing what you do.🖒
@billpickelheimer6323 Жыл бұрын
And I guess from the title and the video you are one of those people that don't know how to weld aluminum ,you dipped the tungsten in the weld many times and instead of stopping and doing a clean on the tungsten, you just kept on cobbling up the weld
@stevenconnor42212 ай бұрын
I would not have chamfered the sides of the metal as it is too thin you could have used that as part of your molten pool. Also your amperage was set too high hence the splatered look of the weld. Turn the amperage down and build up your molten pool then feed your wire in whist carrying out a circular motion to move the molten pool. Then back of the amperage ( with foot pedal) as the molten pool becomes wider as that is just the aluminium heating up. For aluminium i keep all things for aluminium only and change everything out when welding steel. Stainless steel wire brush , wet n dry , and a rub with acetone. Plus you should keep a grinding wheel or at least a part of it for sharpening tungsten for different materials that your welding. Keep it up and apply all the tips you get, it will make you a better welder.
@user-ok3wm8jw6r Жыл бұрын
Тебе бы поучиться бы самому !
@user-ds2cw8hx8m5 ай бұрын
Думаю автор специально сделал эти ошибки, название ролика об этом намекает. Прикалывается
@warrior-0f-light Жыл бұрын
Friend, see @TIG TULA (Ivan). the weld should go down and form a metal fusion there on the first pass. You didn't clean the parts from dirt, so there is a lot of smoke, the weld is boiling and there are a lot of pores. Learn and you will succeed. I am also learning.
@acojankovic29356 ай бұрын
Ovo je legura aluminijuma!!!
@user-pg3hj2zw2s24 күн бұрын
Я когда-то тоже так начинал,но всё приходит с опытом! Удачи тебе,коллега!
@yeha1143 ай бұрын
Kena bully bang 😅😅😅??? Memang bener sih... Saya benar-benar seorang pemula, tapi saat saya melihat pertama kali saya kaget, baru kali ini saya melihat video tutorial las tig dengan cara mengasah tungsten model begitu. Yang saya ketahui harusnya runcing dan agak sedikit langsam panjang, bukan "bujel" seperti itu, karena setahu saya juga, nanti berpengaruh ke keluarnya api, kalo bujel pasti apinya buyar dan nyebar, gak bisa fokus
@braiid Жыл бұрын
That's about as bad as it gets, glad it's not my engine....
@jlyon228 Жыл бұрын
I knew something was wrong from the start when he ground his tungsten.
@kirisameM Жыл бұрын
😂
@alancollard89394 ай бұрын
im no expert but have been welding alloy for 40 years , first its got to be bloody clean , acetone cleaned , then i preheat it , then it welds with half the amps
@jasond5405 Жыл бұрын
Im no tig welding expert but i have never seen someone tigweld like that before!!!
@hofhadrien40112 ай бұрын
😂
@user-qu3dm2uk2u Жыл бұрын
Я бы не сказал что ты умеешь варить😂
@user-zj3dc3jw8x Жыл бұрын
Меня хватило до тех пор, пока он стал неправильно затачивать вольфрамовый электрод, дальше и смотреть не стал, накс точно не сдавал
@DEMI_GLAS Жыл бұрын
ГлАзаааааааа 😮
@Velokon8 ай бұрын
Я не понимаю, зачем делать разделку шва под нож, если нет проплавления с другой стороны и кто так точит электрод?🤣
@leedale4008 Жыл бұрын
No Pigeons were harmed in the making of this video 😊
@issarashid239 Жыл бұрын
I would have been upset if he had killed the ant that tried to tell him, "Please stop," you are not fit for this field 🤣🤣
@hubbunchdd60353 ай бұрын
What alloy rod did you use. What motor did this case come from?
@TheSkoGe Жыл бұрын
Придраться можно много к чему в его работе, но она сделана, трещина заварена...
@billpickelheimer6323 Жыл бұрын
Maybe a nice carbide Burr would do a nice job ,you could clean it and bevel it all at one time , you need to get something to rest your torch hand on so you can keep consistent and not constantly dipping the tungsten in the weld
@user-xl1io2tl6l Жыл бұрын
Парни судя по тому как этот человек делает разделку шва я думаю что он над нами просто издевается
@nik23-53 Жыл бұрын
😂👍
@user-Bars9 Жыл бұрын
Муравей тоже хотел посмотреть, но его сдуло😂
@user-mg9gw4ir2m Жыл бұрын
Вот вот...Сижу и плАчу- так муравья жалко!
@Pikulev_Evgeniy Жыл бұрын
Тоже в комменты полез, сразу после сдутия муравья. 😢 жалко
@user-qg4kd9jn9x Жыл бұрын
Такой же как я лепило😂😂😂😊 но я еще и учиться толком не начал!
@rouzbehrouzbehani24235 ай бұрын
the special point about tungsten electrode tip sharpening (preparing): you should take tungsten electrode parallel with direction of rotation, it cause electron motion become easy and without obstacle. vertical lines will be created by perpendicular with direction of rotation will create obstacle against the electron motion.
@Dufalak Жыл бұрын
Даже у меня, без опыта, и то шов лучше. Я думал, когда он второй раз проходил наружний шов, будет красиво, но нет же, как было уёпищно, так и осталось😂😂😂 Но держать будет, болгарочкой шлифануть и норм в принципе, но не надо показывать это как пример.
@MOTO_EQUIP_BIG_n_BURLY4 ай бұрын
Спасибо за кино! Действительно, сварка алюминия требует определенных навыков и опыта. Я понимаю, что еще многое предстоит изучить и попрактиковаться, но старания развиваться и совершенствовать свои навыки - это ценно весьма. Благ! 😉
@leoleo3115 Жыл бұрын
Ну на первый раз даже хо-ро-шо
@lukgrz76 Жыл бұрын
Jak widać z filmu, wciąż są tacy którzy nie wiedzę jak prawidłowo ostrzyć elektrody do TIGa. Elektrodę powinno się ostrzyć na sztorc, aby wzdłużne rysy ułatwiały odpływ elektronów w kierunku spawanego materiału.
@frankbowman22 Жыл бұрын
After watching this video I had a serious flash burn and he also did not use the right filter on the lens of his camera😂😂😂
@robertblackshear89636 ай бұрын
😂😂😂😂😂😂😂😂😂😂. It was an extended solar flare 😂😂😂😂😂.
@koyaanisqatsi31610 ай бұрын
1 When tig welding aluminium, there is not much sense to make a sharp point. It will get a rounded tip during welding. 2 Use a stainless steel brush for cleaning. Never use steel (rust). 3 Avoid touching the part with the tungsten while welding. You'll get contamination in your weld and it looks ugly. 4 You really didn't use a step drill for grinding, did you? 🤦♂️ But on the other hand, the part is repaired.
@luixac6 ай бұрын
Bien. Me gustaría saber qué electrodo, amperaje y aporte?? Gracias
@pavelbolkhovitin3687Ай бұрын
заточка вольфрама это ладно, но ступенчатое сверло в виде фрезы на шурике, это шедевр )))
@REMONTKachyg Жыл бұрын
Чтобы внутри не варить достаточно обратного валика. Грязь, поры в шве. Зачистка ну так себе. Направление заточки вольфрама не правильное. Поиграться с настройками и можно за раз проварить, только снаружи. Ампераж больше нужен. Короче смотрите канал @TIG TULA Иван научит.
@Dufalak Жыл бұрын
И частоту добавить, на слух герц 70-80. Прав?
@REMONTKachyg Жыл бұрын
@@Dufalak наверное. :-) ему виднее. Можно и на 60 герц сваривать, прогревается лучше, но очистку надо делать более тщательнее.
@bamrem22874 ай бұрын
Theres a lot of professional comment here..thanks to this video..now i will continue weld my spaceship with my new knowledge here.😊
@user-pt9kh6mv6k Жыл бұрын
Я хоть и не профи тоже, но электрод знаю как правильно затачивать, да и швы по симпотней делаю.😉
@urbansimoncic86238 ай бұрын
Suggestion for edited title: Many don't know how to weld aluminum. It turns out that I am one of them.
@chriswoods22638 ай бұрын
i had to laugh when he started using a step drill as a Carbide Burr
@EMC73Ай бұрын
До сих пор есть те, кто неправильно затачивает электрод и варит с дефектами шва😂
@wsx123_- Жыл бұрын
Хочу отметить мастерскую работу обеих рук,всё видно прекрасно,особенно момент погружения расплавленного припоя в сварочную ванну. P.S.смотрел в маске.
@StupidBlokeStupidVideos Жыл бұрын
At 1:12 I realised that the person in the video doesn’t know how to weld aluminium either 😂
@user-xv5mn9xi9vАй бұрын
Маэстро! Брависимо! Самое ценное в этом видео, сам момент сварки.
@yoelzalazar615 Жыл бұрын
Otro nivel de soldadura eso es con corriente alterna ??
@kulibin24932 ай бұрын
Моё почтение,но вольфрамовые электроды для тиг сварки так не точат,камень должен набегать на остриё при заточке ,должна быть риска вдоль электрода но не так как вы заточили,дуга постоянно будет плясать.
@user-jm2jo8rv2v Жыл бұрын
Мужик,аргоновая сварка-это явно не твоё
@josemanuelpombeiromedela977 Жыл бұрын
Demostró que sí se puede... tú solo bla bla bla.
@user-kh1zp5kb2s Жыл бұрын
Инструкция. Как НЕ надо делать. Запомните и больше так не повторяйте.
@DedyIIIka_Igor Жыл бұрын
я профан в этом.а что не так он делает?
@moto_gnom Жыл бұрын
@@DedyIIIka_Igor плохой провар,он даже электрод точит не правильно
@moto_gnom Жыл бұрын
И режим пульса сдесь не уместен.скорее всего человек только начал учится
@user-mk5se8ec2m Жыл бұрын
@@DedyIIIka_Igor еще обезжирить ОБЯЗАТЕЛЬНО!! ощущение что совсем новичок, хотя бы азы выучил бы.... обработка зоны шва болгаркой и ступенчатым сверлом) - вообще то давно изобрели фрезы! в tig сварке для хорошего качества соединения очень важна подготовка поверхностей. Электрод точится не так, риска должна идти вдоль электрода а не поперек, в идеале полировка, вообще это основы сварки, это то что в первую очередь при обучении объясняют)
@moto_gnom Жыл бұрын
@@user-mk5se8ec2m обезжиривать не обязательно,такие детали лъют из говнячьего силумина и хоть окуни в растворитель это толку не даст
@wernerholm634 ай бұрын
Hallo, wie sieht denn die Schweißnaht aussen nach dem schleifen aus? Also, sind da denn noch Poren? Und welche Balance und Frequenz Einstellungen hast Du am Gerät eingestellt? Grüße🤘
@fishhuntadventure Жыл бұрын
I’m not “accomplished” at TiG. Developing as a new skill. But my tungsten gets sharpened well; though my welds aren’t consistently pretty yet I’m reasonably certain that a die grinder and me would wind up welding better than this.
@rafaellencinilescano5616 Жыл бұрын
No alumínio não se afia o tungstênio. Vc deve inverter os cabos e fazer da ponta uma esfera.
@user-tg7db9oh5b13 күн бұрын
Поперечная заточка электрода, сразу настораживает
@user-cs2kr3zu8g22 күн бұрын
"there are still many who dont know how to weld aluminum using tig welding, including me" i fixed your title
@user-tj7qc3nf9h5 ай бұрын
알루미늄 용접봉은 따로 알루미늄 용접할때 쓰는 봉이 따로 있나요 ?
@TheOriginalAndysGarage6 ай бұрын
He sharpens the tip then puts it in backwards, you have to admit though he's probably a better grinder than a welder
@baderel66787 ай бұрын
The method of welding aluminum consists of dots, not a single line. This only works with carbon tubes
@maxsudmirzaboyev74532 ай бұрын
ролик надо было назвать до сих пор я не умею сваривать алюминий аргоновой сваркой
@lukmanrachmadina38 Жыл бұрын
amper terlalu besar,goyangan tangan antara stang dan pakan diperhatikan lgi untuk,untuk penyambungan yg space lebar dan panjang harusnya dicantum dibeberapa titik,pembersihan lebih baik pake tuner mas,pelajari lg penajaman tungsten... Semangat belajar terus..💪💪
@SwaRgOn56 Жыл бұрын
А чо ноготь большого пальца реально поможет ковырнуть глину при запоре!
@user-qx2yl8qh5n13 күн бұрын
Познавательное видео, как не надо сваривать. Ребят не учитесь плохому. Потом замучаетерь руку перенастраивать....
@chughes448 ай бұрын
Are you using a step bit as a grinder!?
@user-yb2nx2sh2k Жыл бұрын
В этом видео только один момент был правильный, это когда автор видео делал кромки не абразивным кругом. В остальном: заточка вальфрама, ток, сварка через жопу.
@papakalli2 ай бұрын
Ich lerne gerade in Wig Stahl klappt soweit erstmal... Jetzt habe ich versucht Alu zu schweißen, aber es klappt nicht. Alu habe ich aus dem Baumarkt, solche ALu winkel, ca 2mm stark. Maschine steht auf AC, Argon 4.6 steht auf 10l min. Habe von 35 Ampere bis hoch auf 200 alles Probiert. Das Alu wird ja so irgendwie Bröckelig bzw sieht aus wie die Mondlandschaft und Verbrennt irgendwie, also am ende Verschwindet es. Der Alu Schweiß zusatz schmilzt, aber es bilden sich Kugeln die dann bleiben. AC Balance habe ich von 10 bis Max auch schon durch. Was mache ich Falsch?
@user-qv4lf4cn9i3 ай бұрын
Человек молодец! Сбил, сколотил - вот колесо! Сёл и поехал - как хорошо!!! Оглянулся назад - все спицы лежат!) Но на самом деле он показал, что в гаражных условиях можно что-нить и как-нибудь заварить и решить проблему. Молодец
@user-hk2fb8lx5o7 ай бұрын
Зачистка конечно важна не спорю и то что сверлом он чистит в принципе нифига плохого, но прикольно конечно, я не думал о таком способе😆. Режим пульс, так то можно и без него в принципе, но можно и так че такого та. На мой взгляд, я хоть и не профи, мало тока в следствии нет провала вообще. Вольфрам точу на алмазе, длинна заточки равняется примерно двум диаметрам электрода. Готов выслушать критику, дабы улучшить свои знания в этом деле. Всём удачи 😁😁😉
@jakequinn487011 ай бұрын
Can’t weld don’t weld😂
@weldingwelder Жыл бұрын
How to weld Aluminum = clean clean clean lol
@Bureev.s_Workshop4 ай бұрын
До сих пор есть люди, которые даже электроды затачивать не умеют. 😂
@user-wi2gp3my3f Жыл бұрын
Закрыл видео на моменте заточки вольфрама 🤮🤦♂️
@engjds5 күн бұрын
I launched a log this morning that looked straighter and less porous
@user-oh6ex6rk3x Жыл бұрын
do you have vedio to explain this machine how its work please
@user-er7zo1pq2b2 ай бұрын
Самоирония на высоте.
@tryandtakealaska3797 Жыл бұрын
5:56 uses a HF step bit as a carbide bur haha lol im king of cheap but piss on that spend 10 and get a carbide bur just spin on a wax candle to stop alum sticking in the fluts. thanks for sharing
@user-dh6gq3sj7d4 ай бұрын
Блин, тут как бы уже все всё написали, добавить мне больше не чего, на разделке фаски и заточке электрода можно было переключать видос
@eldiyarraikanov7287Ай бұрын
00:01 муравья жалко😂 не оставили никаких шансов ему
@youtubevideos42826 ай бұрын
veja amigo se voce arredondar a ponta do tungstenio não havera formação de porosidade no cordão de solda.thank you for your video .
@mucahitgoren5 ай бұрын
Sadece alüminyum kaynağında sanırım? Değil mi?
@user-fi3sw8cd9g2 ай бұрын
Муравей первым всё понял))
@ofinamarciocoelhomoraes9432Ай бұрын
E isso professor você conhece dimais fico tope dimais
@user-jf8fo9mw6w10 ай бұрын
до сих пор много тех, кто не умеет сваривать алюминий аргоновой сваркой, а так же не знающих, для чего ступенчатое сверло и борфрезы
@Hernz Жыл бұрын
"The way his bank account is set up" / sums it all up.
@rubenbernat5587 Жыл бұрын
Antes de soldar hay limpiar bien la pieza. No luego,por eso ha salido mal la soldadura.. Y sobre todo se recomienda calentar la pieza para poder hacer una buena penetración y soldadura. Han habido demasiados fallos. Es difícil soldar el aluminio si no sigues unos pasos básicos. Pero bueno, dentro de lo que cabe no lo ha hecho tan ma.
@user-gx8kk4gp3y7 ай бұрын
Греют толстый алюминий, а этот и дуга прогреет Ампер побольше и вперед А вот то что он на импульсе варил это уже странно, как минимум
@maxpeckham9668 ай бұрын
Entirely how NOT to weld aluminum. Lol
@teknikmadani Жыл бұрын
good job
@rinfin9103 Жыл бұрын
я лично, видел один только белый вспышку от сварки. Многим было бы интересно, как сам процесс сварки идет!?
@jamesbarthelemy59267 ай бұрын
The ant was literally Neville from the scene where he tries to stop them from breaking the rules
@user-pf8sy5lz5k Жыл бұрын
Вентилятор нужно ставить,все пары в лицо,а так лайк 👍