No video

Timing Belt - Part 1

  Рет қаралды 4,942

The Z Garage

The Z Garage

Күн бұрын

This video is the first part about taking off the timing belt. As always be very careful because much of this is very important to the engine. If you have any questions please leave them below!!
The link to xenoncar article on the replacement of the timing belt and torque specs: xenonzcar.com/z...
Check out our website: TheZGarage.net
I am not a professional mechanic and the methods described in my videos are solely based on my research and intuition. I make mistakes and when I do, I try to point them out so others don't make the same mistakes. These videos are meant only as a description of what I was trying to do and how I went about doing it. Before attempting any service on your car, conduct your own research and use common sense.

Пікірлер: 13
@scottscratcher1220
@scottscratcher1220 6 жыл бұрын
Thank you for your time and effort with these videos for the Z31 , I have a Nissan 1988 z31 and need to change the exhaust manifold on the left side , the valve coversand the top oil seal is where all the fun stuff to remove is so keep up the good work and thank you again
@505ighter1
@505ighter1 21 күн бұрын
None of the bolts from puller kit fit the bolt holes on my hb pully.
@clarkkent4991
@clarkkent4991 Жыл бұрын
🏆🏆
@donvergas6412
@donvergas6412 3 жыл бұрын
Wassup man, bout to dive into this myself. Quick question, I see (at least i think i do lol) you didnt have it set at tdc before you took the belt off. Is that of any importance at all?
@TheZGarage
@TheZGarage 3 жыл бұрын
It helps to get everything back in TDC when you put it all back together. I recommend doing it since the cams and crank have to turn together
@FleetTech97
@FleetTech97 4 жыл бұрын
Why isn’t the red dot on the cam sprocket lined up ?
@TheZGarage
@TheZGarage 4 жыл бұрын
The dots are more to get it in the right area and then as long as there are the correct number of teeth between the dots, that's the most important part
@FleetTech97
@FleetTech97 4 жыл бұрын
@@TheZGarage but I mean those dots when lined up tells you it’s a tdc on either cylinder 6 or 1. In the video the cam dots looked like they were 180 off? Just wondering if you were setting it on tdc on another cylinder.
@Shawtydabomb
@Shawtydabomb 3 жыл бұрын
Hey man how did you get your fan clutch off?
@TheZGarage
@TheZGarage 3 жыл бұрын
The fan clutch is held on with 4 nuts onto the water pump pulley. You just have to use a wrench and go at it slowly
@Shawtydabomb
@Shawtydabomb 3 жыл бұрын
The Z Garage oh ok thanks yea I took another look seems pretty simple also hey if you wanna see my 300zx go to my Instagram it’s daily_3.0_z31 I just got it and it’s very clean and only has 111k miles
@TheZGarage
@TheZGarage 3 жыл бұрын
I'll have to check it out!
@darthmittens5863
@darthmittens5863 4 жыл бұрын
Balance shaft puller or a pulley puller my man ;) 😂
Timing belt - Part 2
14:14
The Z Garage
Рет қаралды 9 М.
Z31 300zx Fuel Pump Upgrade
7:52
Turbocharged Creations
Рет қаралды 29 М.
7 Days Stranded In A Cave
17:59
MrBeast
Рет қаралды 92 МЛН
Кадр сыртындағы қызықтар | Келінжан
00:16
ОБЯЗАТЕЛЬНО СОВЕРШАЙТЕ ДОБРО!❤❤❤
00:45
Schneider Racing 292h Cammed Z31 Walk-around + Rev!
4:39
Turbocharged Creations
Рет қаралды 38 М.
Z31 Timing Belt Replacement
14:19
Cars N Stuff
Рет қаралды 13 М.
Installing a 3 Row Radiator in the Z! (300zx Z31)
14:00
The Z Garage
Рет қаралды 4,7 М.
300zx Z31 Gets New Fuel Pump (Deatschwerks DW200)
29:35
Jake's SCC
Рет қаралды 8 М.
How to replace your CAS (300zx Z31) Start-up Issues fixed
6:40
The Z Garage
Рет қаралды 14 М.
How to drain your coolant! My 300ZX Z31
5:26
The Z Garage
Рет қаралды 9 М.
Nissan 300ZX (1984-88) Front Strut Replacement
17:52
Budget Boosting
Рет қаралды 27 М.
NISSAN 300ZX Z31 FAULT FINDING GUIDE
10:46
VideoToGo Darwin
Рет қаралды 17 М.
7 Days Stranded In A Cave
17:59
MrBeast
Рет қаралды 92 МЛН