This time the Junkyard TXL Indy Runs and Drives! Vintage Polaris Snowmobile Resurrection!

Рет қаралды 3,202

5 ай бұрын

This time we get the 1982 Polaris TXL Indy far enough together to take it for a ride. Does it go great? Well, it doesn't go great but it doesn't go terribly bad...
Want to support the channel? Go To Nutter's Speed Shop Patreon Page: / nuttersspeedshop
or
Send beer and pizza funds through Pay Pal to nuttersspeedshop@gmail.com. No questions about sleds will be answered by e-mail. Leave a comment. Comments help the channel, e-mails don't.
or
Want to send Farley dog treats or send something to Nutter's Speed Shop?
P.O. Box 241
Stacy Mn 55079
Shirts and stickers are here: nutters-speed-shop.myspreadsh...
Brass fuel tank pickup with screen for 1/4" fuel line. amzn.to/46d5k91
Battery I used for project Walnuts amzn.to/3rvxb5r
My favorite (almost) universal tether. Works on all vintage Polaris amzn.to/3LLn3gm
99502H 2RS bearings - oddball smaller bearings used in some Polaris skids. amzn.to/3D9yLfO
Rivnut tool we use in the shop: amzn.to/3H98pNp
The O-rings for Polaris TX carbs amzn.to/3wc25hG
Shoe Goo -- Fix your sled seat! amzn.to/3XAJfgc
Shake and Break! The Ultimate Philips impact driver! amzn.to/3CcJgyk
62052RS bearing I have been using. Cheap, but seem OK for my use: amzn.to/3h2ZimS
Wix 33001 1/4" Fuel Filter for sleds: amzn.to/3zs1x9A
Brass 3/4" hose barbs: amzn.to/3Fvrjh4
Spring Compressor - right size for sleds: amzn.to/3MU5Jo1
Really deep 12mm socket for above compressor: amzn.to/3uIDyjE
9/16 6 point socket, 1/4" drive: amzn.to/3EYDQcF
Mayhew Dominator Pry Bar set: QUALITY!!! amzn.to/3yvg0B6
Genuine Hella H4 headlight for wedge Indys: amzn.to/3LjQOmq
Insulation for belly pan near pipes: amzn.to/3DqyOEU
7PSI lever lock radiator cap for Vintage Polaris (large cap) amzn.to/3BhUjVN
1/4-20 flat nuts for vintage Polaris: amzn.to/3qGa18e
9mm hose clamp for fuel lines: amzn.to/3xBS51Q

Пікірлер: 30

@nuttersspeedshop 5 ай бұрын

Want to support the channel? Go To Nutter's Speed Shop Patreon Page: www.patreon.com/nuttersspeedshop

@toddclyne3493 4 ай бұрын

Tommy has been a great addition to the channel and I gained a new friend by meeting him. We had the same problem when test 2 Bag when it was 45 out. Rich rich rich

@nuttersspeedshop 4 ай бұрын

It's been great building sleds with Tommy again.

@IndyGuyRob 4 ай бұрын

Cheers Guys ! Clean the carbs!! Good to see another Indy back out there 👍, especially an 82! You guys could almost do these blindfolded by now lol Braap Braap! 🍻🍻🍻

@nuttersspeedshop 4 ай бұрын

Cheers Rob!

@timwendt6186 5 ай бұрын

We really enjoy your KZfaq videos. Thanks Nutter for mentioning my name in your video for the pizza. Please keep doing what you do. You really made my day and I really needed that.

@nuttersspeedshop 5 ай бұрын

Thanks again!

@TCM_Productions 5 ай бұрын

Grass drags in February... wow, don't recall that since like '82 I don't think! Realize ya'll been around the Polaris block and this isn't a pure hot rod, but all those Fuji liquid twins can easily take 10-15 thou off the head and still be pump gas friendly, sure wakes them up and you already did the 38s---- mizeall....;)

@craigcooper9328 5 ай бұрын

Sunday's are so awesome first thing I do is grab my phone and watch your video Nutter I've learned a lot about sled's

@nuttersspeedshop 5 ай бұрын

Thanks!

@clifffoltz651 5 ай бұрын

Nothing like this February snow ! Lol❤ Excellent videos guys ! Maybe we'll get some riding snow still ! Who knows !😊

@nuttersspeedshop 5 ай бұрын

I hope so!

@IowaBudgetRCBashers 5 ай бұрын

I see you guys have the same amount of snow we do here in Iowa. The hole saw bushing is genius. My brother did my carbs on my 90 prowler, and the new main jets had a different taper than the originals, it’d idle but loaded up when trying to rev it up. Had to get new needles to match the Chinese jets. Sure wish we’d get 1 more snow so I can ride it. Great video guys

@nuttersspeedshop 5 ай бұрын

Lakes are open here. I'd still go ditch banging if we got some snow, but it's not looking good.

@craigcooper9328 5 ай бұрын

You can never have enough sled parts I just went out and bought it 94 ski doo mx 470

@nuttersspeedshop 5 ай бұрын

cool

@alecjagol2447 5 ай бұрын

I sent some pictures of things I got Mr nutters

@nuttersspeedshop 5 ай бұрын

@user-vc1jk9wl6q 4 ай бұрын

You need to get a old Victory motorcycle and paint it up as a TXL.

@nuttersspeedshop 4 ай бұрын

that would be cool.

@billreichheld4839 5 ай бұрын

been watching your videos for a while now nice to see all these old sleds being fixed up cheers guys

@nuttersspeedshop 5 ай бұрын

Thanks!

@user-bp1wm7iw3j 5 ай бұрын

Great video ! What kind of temp gauge was installed? Is it into a coolant line? On the heads or in the exhaust ? Any info will be greatly appreciated!!

@nuttersspeedshop 5 ай бұрын

Just a cheap auto parts store temp gauge. Fit right into the head with one of the adapters that came with it.

@kevinandres5053 5 ай бұрын

When you weld on the sleds with cdi has the welding ever caused problems with the cdi?

@nuttersspeedshop 5 ай бұрын

As you can see in this video I really like to take the motor out. If I can't take the motor out I always unplug everything and if possible remove the CDI. Also be sure of your ground path. Even then it's risky, so pull the CDI out of the chassis whenever you can.