That Transmission Came Out Super Clean! 💯

“I’m not looking to make it perfect” makes it look perfect!😂

I need to remember this the next time I'll clean my car - remove the engine, spray it down and reinstall. :')

It’s a Saturday morning, having a cup of coffee and staring at my DD 91 LC and my newly acquired 94’ LC train wreck and looking for inspiration. This is certainly the right channel. Your hard work and well sorted efforts are appreciated.

Don't let perfect be the enemy of 'done'...

Shockingly clean! Didn’t think there was any hope for that transmission grime 😂

Awesome job, I’m sold on Super Clean!

Great video Ricky, such a satisfying job - and even to watch! Does the Super Clean come with the sick goggles too>! :D ;) Stacey and I both were like, "wow those fenders are green!" lol

May as well replace all your pressure sensors on the transfer case now too. They go bad and cause your CDL to not engage. There's lots of info on mud about it. Love the vids👌

You should be fine to support the trans on the pan, just use a block of wood in between the jack (according to the FSM).

great work. I'm humming along with you and my 94, built the harness like you as well with tesa and all that, thanks for the recommendations. One thing I am doing is having the steering box rebuilt with the 105 sector shaft. Common failure when offroad

I did the same with my mitsubishi eclipse. I also used two detail brushes just to get the spots that are hard to get

Subbed! Fellow Toyota guy here. I’m in the midst of rebuilding the engine and trans in my 2000 Celica GT-S. Going to use this method to clean all the oil grime up. Thanks!

Good work man! Looks so good

amazing video good job

awesome work

Who ever installs a dirty part should never touch another vehicle ever

Super clean!

nice work. Is your pressure washer hot water or cold? Is it a hi pressure or is it a cheapo model like mine?

If you ever do this again I would try to get a pressure washer with a heater and get the temp of the water to 180 degrees melts oil pretty good

Which do you think works better? Liquid or foam?

Looking good! Is it possible to leave the lines and cap? That way you can easily hook back up in future if need be. Keep up the good work!

Make a little stand to hold the transmission up. Craft it out of 2x4s

I'm in trouble a little bit with my newest project. OCD. IT'S GOT TO BE CLEAN!!!

Your my hero

Should look into at wits end rear heatee delete plate

Super Clean ! I needa do this for my 80 cuz my front main seal has seen cleaner days 🤣

Nice work! what kind of pressure washer are you using?

Would you like to tell me the name of this degreaser because am from Pakistan

New subscribed from Somalia

Just use a hot steam pressure washer. No materials required. That's what they use in UK before they do bus/truck/lorry mots.

EPA will be visiting soon I bet 😂

Just use starting fluid. Spray on .watch it do its magic

imagine having a real pressure washer u wont need second pass

😮😮wow

I'm thinking a 3000 psi pressure washer would do a much better job maybe even get a jitterbug nozzle

If I had cleaned it like you, only here in Germany, I would certainly have gone to prison - environment 😂🤦🏼‍♂️ But, Great Work!🎉

I wonder what all that cleaner did to his lawn.

After just a wash : For sale fully rebuilt 6000$ 😂😂😂

Use a cherry picker or what u call engine hoist

next time use heavy duty stove/ oven cleaner

what was the issue for cleaning the bottom/underside of that thing? you can.t just go down on your knees on the waste you just spread all around and wash it off? kidding? i get the idea people are all office workers who play tough...

God almighty...who has the time for a project like that?!

Bro you need a better brush...

at least he does not claim to repair anytjing with electrolysis or cooking methods in degreaser soup....all those methods are idiotic and ruin parts, his solution is agressive but better...best resluts you get with an old spray bottle from some window cleaner, fill iit with kerosene or Diesel....put some plastic and heavy card board under the engine,,,.spray the gunk and crape and brush it off with some stiff platsic toilet brush or sink brush or the like....the engine should not be dried out ir become wet at all, we only remove the gunk...and for that we use some heavy solvent without any fire hazzard....use gloves( latex or nitril) ...1 -2 hours for a whole engine compartement🤷‍♀️doens,t harm plastics or rubber/ neoprene at all....leaves the old shiny metal appearance of an ( almost) newly assembled engine... many use oven cleaner and like he does wheel cleaner....wouldn,t do tthat as engines nowadays have lots of sensors and electric parts on it....and NEVER. use a brass brush on aluminium,,,.just get some discount 1,-/ pc, plastic brushes for whatever,.....and it really goes off well, then a lot pf kitchen papaer or shop cleaning paper....or old fabric scraps....and at the end all rolled up into the plastic/ big trash bag....off to the trash for burning without any pressure washer, no pollution to the groundwater or your yard,,,,it.s horrible how many oressure wash the engines in their garden! and wash some soup from detergent and solvents mixed with heavy metals and old oil and rust simply into the ground! for what? kerosene for lamps, one liter...3-5 bucks? a plastic scraper amd a brush.some gloves...makes mostly 10 bucks, and you get cardboard from Aldi for free, a trash bag or old plastic...cents! 🤷‍♀️and basically all around stays mostly clean! i did dis several times just in bikini and sandals and left the engine in my car...after the third time and chnaging the head gaskets to get the engine tight my car.s engine bay looks like now on a 1995 convert! my mechanik loves my car! the cost were minimal...4 th year i had nothing to clean anymore as she was dry and started to rust on the cylinder heads, bought 2 cheapest discout engine silver spray and picked up a pack of elswise trashed adverts paper ...costs ? 10 bucks again! ? 🤷‍♀️2 hours later my engine was silver, , stays rust free for 4-5 yrs now, same goes for the chassy....but we now fill all ridges and gadgets with heavy duty greasy ....once a year clean and spray the seams on the sheet metal parts on the underside...check on some simple places( never told in manuals) for greasing the hand shift and if the mechanic 6 yrs ago would have messed up the belt set job whixh sprung over this winter after just 60.000 km...( so basically just 2/3-1/2 of the official life! ) i.d haven,t had any issues that cost me 2 k extra...my new one switches some parts like suspension or tires or bearings every secomd or 3 rd year and my engine just gets new oil and filters...plugs ince in a while and runs like crazy....no gunk and no oil and nothing anywhere! AND NO DEGREASER ON ANY ENGINE !

one should repirt this to the environmental agency for water pritection🤮pls never do this! see how blaxk the grass has become all over the place! it all soakes down into the ground water,...yes that,s what we actually drink! don,t do it the way he did! never!

Get a better nossle

Doesn’t look so amazing.

These are not good degrease. They are not working at all. Good degrease should instantly dissolve the grease without pressure wash or brush wash.