I had severe jittering at about 97-99% and 0-6% throttle. This complete fixed my issue. Thank you so much!

I don’t know if you’ll ever see this but it would be rude not to say thank you! Saved me a chunk of money and a massive gap from flying while I saved up! Really appreciate your video

You are a life saver. Was about to purchase a new throttle. Followed these steps and it's as good as new. THANK YOU!

Just did this and it completely resolved the jumping issue that the throttle had been exhibiting for me previously. Thanks for the guide!

Hey man, just wanna thank you, found this video of yours and worked wonders for me. Just out here to send my appreciation. cheers!

Thank you from this, I recently replaced the grease with the nyogel 767a on the slide rails and thought I messed something up. This not only fixed my issue, it's smoother now than when I first got it, thank you so much

It fixed the jittering. Very nice. Thank you

Thanks, very useful video ! Saved me discarding my TWCS when it developed a very noisy pot. I found that I didn't need to unscrew the linkage arm from the throttle handle; I just pulled up on the end connected to the potentiometer and swung it to one side.

Had severe jittering between 30-97% ish. Worked like a charm, smooth acceleration! Thank you for posting this!

Thanks man! Was having hellish issues with mine and ran across this video from a Reddit post. My metal ring in the base of the potentiometer was almost solid black. Took hard scraping with the pick to get it off. Way simpler than I thought it would be! For having only 2 hands when you needed 4, great video! 😂

Thank you my dude! I had a lot of jittering at the top and bottom ends of my throttle. After following the video and some harder scraping on the metal ring, mine had a couple of stains, it is working flawlessly again.

Life saver! I dealt with months of severe jittering at max/center of the joystick, making it super hard to fly properly nor do any AAR, etc. Feels strange to be able to fly normally again.

Legend! This worked for me, thank you so much. TM customer services were useless, they should watch this video themselves to point people in the right direction, as it's clearly a common problem.

Useful. Thanks cleared up my jitter. In the absence of switch cleaner I used plain old WD-40 on the advice of a friend and it was fine.

You saved my day... my Thrustmaster TWCS had this problem and I managed to fix it, but I didn't use spray, I just wiped it off with a swab.

It did fix my problem, like everyone elses in the comments, BUT i had some problems after this fix. Nothing of your fault, its bad design from thrustmaster. After i did what you said. My TWCS didn't want to be recognized by windows. I took it back apart, tested cables, shorts, missing components on the PCB. Turned out it just didn't want to work. After 45minutes of useless diagnosing, it just started to work again. At least i learned something new. Thanks for the fix, it did fix my issues!

Worked for me! Completely smooth input now. I used Isopropyl Alc. for the cleaning, it looked like there was some grease buildup in the potentiometer. The IPA I used completely removed the grease, so might have 'shortened' the lifespan of the part, but at least it works for now.

holy shit, this works! You are the best, OP

Thank You! Just have the same problem and your film help a lot!

Thank you!Fixed my jittering at 100% throttle .

i love you. been struggling with mine and this fixed it. good video

Thanks! You are a live saver. The central screw that hold the arm of the throttle could be unscrewed partially

great video helped me clean and find a broken contact. bit of aluminumfoil and it works like a charm again!

Thank you so much ! It totally solved my problem ! By the way I used some glass spray cleaner to clean the potentiometer.

You helped me alot thanks!

Much Thanks brother, it did help fix the wrong inputs ❤❤

Thanks very much! That worked like a charm!!

Thanks!! just did this and my TWCS stoped jumping in the throttle axis. Removing the cover its quite hairy.. one of the taps broke just pulling it out gently.. so be carefull (fortunatlly didnt afected reasembly) also recomend taking a photo before removing the pot to make sure reinstall is correct.. i couldnt renember wich was upside up or down but had taken a pic and could see a small circle wich was on one side only and up

Thank you sooo much!!! It worked exceptionel.

Thank you so much! This worked for me!

😊 agreed with all the other ppl successfully fixing their tech. Thanks to your video, I managed the fix, 100% successful. Thanks 🙏👍

Fixed my throttle thanks

the little metal thing that pops out, make sure you put it back in with the metal side down, its bent a bit so one side it looks bent up, other side it looks bent down, I had to put it in bent down. Also, I applied more pressure and snapped off the single solder joint on the top, had to re-flow it and it's good, thanks for your help.

Thank you so much! You are my hero.

с помощью этого видео, я починил свой Thrustmaster TWCS! Спасибо!

Thanks man, it's very helpfull for me

DUDE. you saved my throttle from being angrily destroyed with hammers. and somehow the slew hat is now working too despite not touching it!

thankyou! sooo much better now

Thank you! I fixed it!

thank you very much, it worked great

Thank you so much works perfect

Absolute life saver, revived my throttle back to 100% usability. It had severe jitter at blower and idle levels. borderline unusable. Any chance you got any inputs on what can be done with the TDC index stick? mine came with travel in pitch and has a hard time returning to center :(

Very nice ! i used Facom contact cleaner and it worked perfectly ! Thank you !

thank you! thank you so much!

Thank you so much.

i used normal disinfectant spray because i had nothing else and it worked too :D

Opening that plastic tab, super scary. I just stuck alcohol into the hole and it works good as new. We'll see how long it lasts. My T.16000m had a problem with the twist within a week of purchase as well but I use pedals instead.

I live in the middle of nowhere, can i just use normal alcohol to clean it?

Still get a few jitters near 25% and 75%, but it registers 100% now at least!

Lifesaver 🙏

Hey mate, just wondering if its safe to undo the latches without a pick, as i dont have one and this kind of stuff is very expensive in my country

can i do the same thing for the rudder pedal it just stop turning right for msfs but it still works for xplane 11 very strange

I somehow put it back together backwards and now my axis is inverted lol. Time to take it apart again

Which contact cleaner do you use?

Completely fixed all my jittering, it got so bad

hi..can we found this potentiometer?

nvm it works thanks

it kinda fixed it, when i go WAY back, its there but only WAY back, ima just put a deadzone there, still thank you :D

What is that contact cleaner you're using? Is it just WD40?

fucking love you :*

I hope you go to heaven. Thanks to you, it's fixed. Thank you very, very, very much. Greetings from Turkey. 😇😇

Such a tiny PCB mounted pot is just deplorable practice, edging into toy quality. It should be a larger, easily replaceable type, of greater durability/longer life. The carbon film material over time suffers grooves worn into it by the wiper, and eventually will get scraped completely away. There is often utilized a conductive lubricant which reduces this wear. By cleaning it away the remaining life of the pot is shortened. Replacing these PCB mounted things is a more involved process than for swapping out mechanically mounted types, such as found in the CH throttle. And so more of these units will get needlessly trashed sooner than warranted.

Going to try using de-oxit. Amp tech’s best friend.