TIG Welding Aluminum Overhead Tips and Tricks

Рет қаралды 11,925

Жыл бұрын

The Everlast welders KZfaq channel is the only channel in the industry that is run by the welding community, for the welding community. Every week we will release a new episode taught by the best welders in their respective fields.
Everlast welders manufactures premium welding machines with industry leading features. We were the first to release an ACDC MIG, TIG, Stick machine and we continue to be on the front line of welding technology innovation. For more information on our welding power sources or to find the right welding machine for your application, visit www.everlastwelders.com.
#everlastwelders #weldmeanweldgreen #learnwelding

Пікірлер: 15

@billy.b652 Жыл бұрын

As a retired multi coded welder from North Sea in Scotland, my worse nightmare was purging stainless steel on pipe work, sometimes 1 inch in diameter. 3 repairs, and oil companies sent you off for a retest. Some welders wouldn’t fire up, until scaffolders had harped them in, with no wind what so ever, as wind would blow argon away from inside pipe. We would light a match, and if if flickered , then it wasn’t wise to start welding your butt. Only trade to get tested for oil rigs, that’s why we were gods out there. Especially a Babcock n Wilcox welder, who were the cream of welders.🥳🏴󠁧󠁢󠁳󠁣󠁴󠁿👍

@KWSTASKOUTS_KFAB Жыл бұрын

Nice videos 👍

@James.Richter Жыл бұрын

Thanks for the content Jesse 👍

@Alex-jr7sg Жыл бұрын

I would be great if somebody could explain how the "SPOT" works on EXT machines. Thank you for the videos.

@InchFab Жыл бұрын

Oh that's an easy one. 1. Think about the way you would want the function to work. 2. Assume it's the opposite of that. 3. So sorry.

@hectorr814 Жыл бұрын

EXCELENTE VIDEO¡¡... Y MUY ILUSTRATIVO¡¡...SALUDOS DESDE MEXICO¡¡

@StingrayBay 4 ай бұрын

Awesome video thanks Jesse. So that was two nice shiny plates close together upside down, which I can do but what about a corrosion hole in 1/4 inch aluminium plate ground out to say 1/4 inch and clean. How do you fill that? I always seem to end up with a nice pad on the outside(underside) with minimal penetration and filling of the hole. It usually looks terrible from the top side, do you have any secrets to get to the top of the hole?

@rickfuerst Жыл бұрын

I find in my pontoon repair that I'm on my back most of the time

@DevonEilers Ай бұрын

Should do aluminum irrigation pipe

@ThinkFab Жыл бұрын

My 1/8" thoriated tungsten tends to fall apart pretty rapidly while welding 1/4-3/8" aluminum. Maybe it's my settings? What tungsten would you use to weld AC at 250-300 amps? I recently picked up some 5/32" purple tungsten and consumables, but It would be great to see a video about this since I'm not having much luck on KZfaq. Looking forward to more of this welding school progress as well!

@ls2005019227 Жыл бұрын

Well done! Much easier than that ridiculous can trick......😂

@frostback8160 Жыл бұрын

Just had the worst welders flash of my life using my 255 ext aluminum welding it went through my sweater and t shirt I don't wish it on anyone absolutely incredibly painful spent hours in cold shower. with painkillers.

@InchFab Жыл бұрын

Can someone please explain the pulse function when you go below 1.0hz on the pulse frequency? I can't figure out why it's doing what it's doing in that range.

@alfredocuomo1546 Жыл бұрын

What I find funny is you always set your machine with a "1", never 170 amps but 171 amps. So what's the deal with always ending with a one in the amperage setting? A little OCD, Superstition or is there a method to your madness. lol I've been meaning to ask.

@jessemccollum937 Жыл бұрын

It’s pure superstition on my part…. Balance on 0’s or 5’s, amps and freq on 1’s. I absolutely can’t explain it