No video
WE FIXED THE 200HP MOTOR! You’re Not Going To Believe This...
Рет қаралды 135,677
11 ай бұрынFOLLOW NEO GARAGE - / neo_offroad_garage
/ neo_performance_garage
Keep Up With Me Outside of KZfaq!
Instagram- Tightlinetv- bit.ly/2OUdSOC
TikTok- bit.ly/3zVbCvj
@jakegrantham509 11 ай бұрын
The water coming out at different places is normal. Also try not to rev that big of a motor that high while on the muffs. It takes a lot of water to cool a 200. Glad to see people restoring and renewing these engines that were made right!
@johnpitts9456 11 ай бұрын
My opinion is if this motor has been sitting for a while, you should change the thermostat, specifically since you already have them and you also changed the water pump. Because it's no fun having problems out on the water. Their easy to change.
@hudsonsullivan4710 11 ай бұрын
When running a compression test on an optimax you must un plug the two fuel pump connectors located on the vst on the port side of the block also open the butterfly on the throttle body and to keep from getting shocked again pull the kill switch at the controls to kill the spark to the engine
@CoffeeTime9 11 ай бұрын
This is definitely correct. I had my boat in 2007 mercury optimax thinking something was wrong with compression and they pointed out this is the true method of checking.
@gameon2081 11 ай бұрын
Dude, your restoration vids are awesome, so much different than any other on KZfaq, instead of the viewer learn something the viewer participate in teaching the host. Awesome idea 👍 keep them coming. 👋
@jwboilermaker 11 ай бұрын
Nothing better than the sound of an optimax. You can always hear the growl when they start and WOT sound is amazing.
@arthurtaddei1285 3 ай бұрын
Yes if ya like the sound of a Volkswagen
@joemcbulge379 3 ай бұрын
@@arthurtaddei1285 there are 2 stroke volkswagens out there??
@josiahbeasley6093 11 ай бұрын
Glad to see you making progress. In all honesty that is my DREAM boat. I have owned three Stratos boats, and I firmly believe they are some of the best boats ever made. Currently restoring a 1996 Stratos 185. I have been through all the issues you have seen, and they can be a struggle but very rewarding in the end. Keep up the great work! FYI I am not entirely sure about this year model, but my '89, '96 and '97 Stratos' have all had issues with the anti-siphon valve. It is a fitting on your gas tank with a small ball bearing in them that can stick and cause such a headache. It may be the reason for the not-so-smooth running if it is on your boat, but even if they are working fine, I would still recommend removal to avoid future issues.
@Army_Outdoors_88N 11 ай бұрын
🎉🎉Much better progress than the last time. This boat definitely seems like it's gonna be easier to make it a dream rig
@marshpirate2924 10 ай бұрын
I ran Pennzoil Marine Premium Plus for years(10 easy) in my 2004 225 Optimax. I sold it (running) and replaced it with a 300 Pro XS.
@marcaustin 11 ай бұрын
Love these type of vids. Im not great mechanically either but i can't help googling and working on my Merc as well, Awesome boat my dude!
@wyteboymagik 11 ай бұрын
decarb your engine. depending on the hours it's recommended every 100hrs on 2 stroke outboards. this should help boost your compression. few things. never rev your engine up like you did out of water or in neutral lol also when doing compression make sure kill switch is on so you dont get shocked and throttle at WOT
@michaeleads9294 11 ай бұрын
Time to fix those LiveWell lids next and recarpet the boat. Better safe than stepping through or in something per say lol. All the best to you.
@chrisbruce7594 11 ай бұрын
90 to 120 is good what's more important is that all of them are within 10 of each other your good doing a seafoam treatment to it should help clean out any carbon build up and free up the rings so they'll seal better. Which means higher comparison numbers
@davessparetime83 11 ай бұрын
You don't have to use Mercury oil. Any good 2 stroke oil with the proper certification is fine. Compression tests are done with throttle open so cylinders can get air.
@bigbaldfish 11 ай бұрын
Incorrect…an Optimax needs dfi oil.
@willmillett 11 ай бұрын
@@bigbaldfishyou keep thinking that
@bubbleobill267 11 ай бұрын
@@bigbaldfish After putting over 500 hours on my Optimax I’ll say no, any Tcw3 oil will do the job.
@ajherman 11 ай бұрын
@bigbaldfish and there's other options for it besides the Mercury stuff, like XD-50.
@DustinAdams-og3ko 11 ай бұрын
I agree any 2 stoke oil will work fine
@FabienBoulay 11 ай бұрын
The muffs will force water to the pee hole due to the pressure on your water tap.. but that is not an indicator that the impeller is doing its job, you should bring it to a boat landing and test it in a lake, you should see a steady high pressure string of water coming out, not just a little dripping like you have now.
@ChaseDaPlaya 4 ай бұрын
I’ve worked on dozens of boat motors and never seen tap water flow all the way to the pee hole without a running motor. Also when he hooked it up all the way the pressure was fine.
@Siluetae 3 ай бұрын
So ur saying that tap water is different than natural terrestrial water? Like the motor has a preference? All my motors pee just fine whether in the lake or at home connected to my tap@@ChaseDaPlaya
@moncorp1 10 ай бұрын
I agree with a poster below. If you don't get water when you have it submersed in the tub, you're just seeing the pressure from your hose. Keep digging.
@Johnfor3 11 ай бұрын
I had the same issue with an Evenirude. I turned the square muffs so they were vertical and they started working!
@hydrolock 11 ай бұрын
Yes, the water coming out in the other areas is normal. When you motor isn't submerged in water, this helps keep the gears and oil in the lower unit cool.
@jimk4267 11 ай бұрын
not even close buddy...it cools the exhaust. that's why it runs out the prop hub
@kevinsweeney751 11 ай бұрын
That water is perfectly fine period….check your other engines they all do the same your good!! Pretty sure you have a good motor
@lakeguyisaac5284 11 ай бұрын
Quick silver synthetic blend will be just fine to run through the motor I’ve ran in several optimax and it’s about half the price
@dwayneroberts6616 3 ай бұрын
Thank you so much brother!!! Im going out in the garage and throwing both of those POS rectangular muffs out!
@darrellmedley6809 11 ай бұрын
I would check to see if you have a water intake by the trim annode. My suzuki has a third water intake that I have to put tape over so it can get plenty of water with the muffs.
@metz12harofreak 11 ай бұрын
The pressure of the hose is making the lower leak like that. Its fine. And there is a wicked snapping noise from spark loss. You may want to replace at least the wires on that baby. Coils may help one day too. Id take the plugs back out and shoot a touch of 2 stroke oil in there to get those pistons some lubrication. Just a bit. Also some STP in your fuel may help the lower compression.
@ajherman 11 ай бұрын
Sounds like it just needs some hours of a good italian tuneup and a big can of Seafoam in the gas tank with some fresh, non-ethanol gas to get it good and cleaned out. Definitely sounds strong and healthy, I wouldn't be afraid to send that motor.
@MasterMichaelBond 11 ай бұрын
Good job. Always learning something new about boat motor buddy.
@wht02cr125r 11 ай бұрын
Does that lower unit have a low water pickup infront of the nose cose? If so you should tape that up every time you run it on the muffs; big pressure loss if you do have low water pickups and they arent plugged running on muffs.
@isaakridenour7908 10 ай бұрын
Put a piece of tape over the nose cone of the lower unit when running it on the hose. If it’s a torque master it’ll have water pickups in the front too it sucks air when they aren’t covered or fully submerged
@robertmccorkle9656 11 ай бұрын
I hope you ignore all the negative feedback that you get. Only listen to positive feedback from people that mean well for you. You have taken on the giant task of teaching yourself something from scratch about a subject that can be very complicated, high powered outboard motors. You are doing great by learning from all possible sources such as print material, videos, friends, mechanics, and comments from your videos. Keep up the good work.
@joewinkler2168 11 ай бұрын
I've used every oil on the market, cheep to expensive and never had a problem with the two opti's that I have owned and both were older 1998 and a 2000 . Had 2000 hours on one and way over that on the other. The 1998 motor sat for 5 years before I got it. It only had 70 to 90 lbs compression threw out. And I ran it for 6 years. And did minor maintenance. Sold it to recover and that motor still is on the lake running on the weekends. So don't worry about the compression it will get a bunch better after you run a few weeks under a load on the water. And don't ever free rev up any motor. That's a rod cap stretcher. So don't do it! And you will have that motor a long time if you never add any additives to the gas and only use regular lead gasoline, no ethanol what so ever. And you must run motor for 10 to 15 min min before you go kiting across the lake wide open. Merc's need to get hot inside for clearances before you hard pulls.
@TightlineTV 11 ай бұрын
appreciate you!
@austinbraswell1543 11 ай бұрын
I have 734 hours on my 07 opti and have used exactly 3 gallons of mercury optimax oil, My mechanic I've used for years is a certified mercury master mechanic and told me that mercury dfi oil is fine to use, they used to call it premium plus but I believe they've changed the name to premium Dfi oil. I've had very few issues out of mine so far. He told me the optimax oil is good fort people who use them to troll or idle a lot but not required as long as youre using a DFI oil
@chrisbruce7594 11 ай бұрын
As long as its TC3 or equivalent your good it doesn't have to be mercury brand.
@jerryscray1789 11 ай бұрын
Yep that's what I buy for mine. Much cheaper
@muskybites505 11 ай бұрын
The “pee hose” is actually called the “telltale”. Cause it tells the tale if your boat is cycling water lol
@chickenshippfarmsandoutdoo4617 11 ай бұрын
I thought you tried putting it in a tub of water, too? At least you got it working. That's awesome 😊
@danlaur7973 11 ай бұрын
You can also run Mercury premium plus 2 cycle oil safely in a Optimax
@Spoons89631 11 ай бұрын
the water coming out the lower unit and mid section like that is normal. There is a little water that is meant to get past the motor so it can cool the exhaust tube.
@richardrobert4275 11 ай бұрын
When you do your compression test the throttle needs to be wide open. You’ll get higher numbers, the pistons won’t have to work as hard to suck air into the cylinder. Your compression numbers will be higher.
@sethgabbard7705 11 ай бұрын
That’s only on a fourstroke
@danielfrazier840 11 ай бұрын
@@sethgabbard7705absolutely not
@danconn2065 11 ай бұрын
My Merc Platinum Tech advised OPTI Compression test should ONLY be done cold.
@gsman5828 11 ай бұрын
The square muffs are for lower hp outboards. I had the square muffs for my Yamaha 70 hp and the round one for my 175 suzuki. The square muffs wouldn't work on my 175 Suzuki. It's a relief when it's a simple fix!
@Calgon20something 9 ай бұрын
Check the port that the piss hose connects to. Sometimes carpenter bees or other insects build nests in those, causing a stricture or even completely fouling up the port hole. I’ve seen this numerous times.
@AndyWB 2 ай бұрын
Don’t need muffs at all. There’s a port for the water hose to the left of the pee hole.
@user-og5bo1ig1j 11 ай бұрын
Yes its completely normal for water to come out of those spots. 90psi of compression is completely normal for the optimax outboards. They tent to average 90 to 150psi’s
@rosecostanzo341 11 ай бұрын
Dr. Pondhopper Like the board You can track the logistics.
@dgearwar 2 ай бұрын
for what I read on those motors anything below 120 psi should be looked at brand new they will push 170 to 180 but the old they get more compression decreases. but on that hand shouldn't be lower than 120 you might need to have the motor rebuilt.
@chopfer5864 11 ай бұрын
If you have the 4 water intake holes in the lower unit on the bullet/nose cone you need to tape those up to keep it from suckling air. It will pee even faster..
@dang5553 11 ай бұрын
I forgot the octane but I knew 2 opti 1 Yama 2 Suzuki guys they run a 97 or 98;octane non ethanol 5 gallon in each tank. Not cheap to run these newer EFI DFI engines
@tomrizzo1554 2 ай бұрын
A lot of smart people making comments I'm impressed you should charge this kid Consulting fees
@SchmidtFishing 11 ай бұрын
You should gap the spark plugs correctly. They don’t come gapped properly for optimaxs. A good forum is on bass boat central. Look for mercury optimax thread
@lucastirloni9539 11 ай бұрын
Up
@joemcbulge379 3 ай бұрын
We call them poptimax's around here lol sound cool and fun when they run but i've seen so many of them with bad air compressors (expensive part). much prefer just efi or carb merc v6
@riccochet704 11 ай бұрын
Call around to your local boat dealers. Some of them sell the DFI oil for cheap. Just have to bring your own gallon containers. I get it for $28 a gallon locally.
@Moosetraks21 3 ай бұрын
You keep saying you're not a boat mechanic but you do seem like you know what you're doing.
@nexus7598 11 ай бұрын
Best series ever
@tomodonnell9480 3 ай бұрын
If you don't get water streaming out within 20 seconds you will damage your impeller. Square muffs work, rotate the rectangular muff to complete cover to intake ports. Use a big rubber toat to fill with water and fill to cover the water intakes. The boat won't know it's not in a lake. With a new impeller it should pee water within a few seconds. If not you may have an impeller issue.
@kevinbragg4043 3 ай бұрын
I just did the same thing but I used a tank with my lower unit in it. Had the same problem. Turns out the water has to be over the ca. Plate before it will pee 😅
@matthewshelton7362 11 ай бұрын
You can download a pdf manual for the optimax that tells you everything you need to know and how to disassemble every piece on the outboard
@kennethelliott2267 11 ай бұрын
You can run regular synthetic 2 stroke oil in it I know tons of people that do. One is a certified mercury mechanic. I have a optimax you get quicksilver brand that is dfi and it’s like 38.00 a jug. That is what I use.
@randybarger8649 10 ай бұрын
Dude I bet you are a good mechanic just mechanicaly inclined can fix a lot of stuff but you get great comments and watches your way
@jamesbarclay6554 6 ай бұрын
You can take the thermostats out & check them out in some boiling water to see if they will open & close. If they work properly & there is no foren object s in them. Keep using them. Water is not supposed to be comming out of the lower unit cowling. That is probably why it takes so long to start peeing. When you replaced the impeller you might have aligned the water tube properly when you slid the lower unit back on.
@jimlove4541 22 күн бұрын
what does your water pressure gauge show on the dash?? you need to clean/back flush the cooling system . it has silt and sand in it.
@sergiovieira1993 11 ай бұрын
The water coming out those others holes is normal. In the back, the water comes thru the exhaust, and in the front, there's a bushing in the mid section that has to be cooled.
@glamdring0007 11 ай бұрын
Quicksilver synthetic oil is more than good enough for the Opti...no need to spend twice as much just for the brand name.
@racerxv6valvoline424 11 ай бұрын
Great job! just a side note. You should never rev your motor out of water the way that you did. Outboards are not meant to be rev'd in that manner because there is not resistance against the lower end and it allows the power head to over rev...but congrat;s and I love the decal's
@haneysgarage2631 11 ай бұрын
I clamp all the muffs I get so they are tight fitting and it pees a lot better I use the square dual inlet muffs, the water coming out of the lower unit is normal to have the water flow through and out the cooling system
@bryantgwb007 11 ай бұрын
On the port side of the adapter plate between the engine and the midsection there is a plastic nipple. Unscrew the nipple and you will find a screen. This screen can get clogged with grass or sand and restrict water flow
@johnpitts9456 11 ай бұрын
I've had the exact problem on my merc 200, with the muffes. And my son faced time me with his suzuki 90 not pumping water, and as soon as I seen him using the square muffes, I asked him where his round muffes were, and he said he lost them. He just had the motor running fine a few days before. I told him to get another set of round ones. So he got new round ones the next day and it worked fine. He even bought another water pump because he didn't think just changing the muffes would work.
@djmjr77 10 ай бұрын
Always have a quality compression tester.. I went through 3 new Harbor Freight tester before I found one that worked... on the first one, for a couple months, I thought my outboard had low compression until I tested a jetski and it had the exact same low compression.. borrowed a matco tester and both engines had great compression.. that artificially low compression tester could be used nefariously 😂 so make sure someone has a good tester if you sell an engine, dont want to get ripped off..
@ryanschabert7788 Ай бұрын
Oil needs to be dfi oil and water pump still needs to pump quicker than that. Mercs are usually always good with tell tales and good pressure
@BDitty009 11 ай бұрын
The quicksilver DFI oil is cheaper and conforms to all the specs. These Optis idle a little rough sometimes and it seems like it’s got a miss. At WOT smooth as glass. Some say you should index the plugs on these also. All that water coming out in other places is totally normal.
@lakeguyisaac5284 11 ай бұрын
When doing compression test pull kill switch lol also I always do one plug at a time and leave other plugs in with kill switch pulled so no spark
@kencleg7721 5 ай бұрын
Good point
@kencleg7721 11 ай бұрын
Try a bucket 55 gallon drum w a drain cut 1/4 off the top or so see if it draws. The muffs your injecting the water forcing it sorta if she draws from a test tank she’s good should be a stronger pee stream
@VEEZY_FISHING 11 ай бұрын
If you’re able to get your hands on a decent compression tester like Matco or Craftsman, try doing another compression test with one of those. I did a compression test on one of my Mercury motors with a harbor freight tester and thought there was something wrong. Was getting readings of 70,85,85. I used a Craftsman tester and got 110, 115, and 110.
@donlef765 11 ай бұрын
If the engine is running good and does not overheat leave the thermostat alone the only thing I will recommend is use the exact spark plugs that is called for it definitely does make a difference
@CMDAVISs 11 ай бұрын
That's crazy because the square ones work way better than the round ones for my mercury . NY round ones are loose and don't seal and the square ones do. .
@matthewshelton7362 11 ай бұрын
My optimax sounds just like that. It's a normal sound that all optimax make. The compressor makes a certain sound that adds to the different sounding engine.
@Tarponpimp1 11 ай бұрын
As long as the oil says TCW 3 your fine. I was sponsored by Mercury and ran optimax motors since they were introduced in the 90’s.
@jims4539 10 ай бұрын
Run a high mix of 'Seafoam" 16 oz to the gallon. Run get hot and give it a hot soak - run again.
@HardmanOutdoors 11 ай бұрын
The water coming out around the sides is ok depending on your lower unit. The older style, which was typical.
@user-sg9lv3px6w 4 ай бұрын
You should always tank your engine when testing water pump , thermostats will open sooner , also if the muffs aren’t covering all intake holes it will fry the impeller with in seconds 😎
@triplel8704 11 ай бұрын
I run squares on mine and it pees immediately. Dirt dobber might of been doing his job.
@seansanders789 11 ай бұрын
Yeah the water coming out like that on the lower is normal. Once in the lake water wont do that when submerged.
@toddandersen5742 11 ай бұрын
Might want to try Atwood 9372-2 muffs. Yes the muff issue is a common one.
@vistkri 4 ай бұрын
These outboards sounds soo good👌🏽
@o2man98 11 ай бұрын
At 16:35 look just to the right of the hose on the compression tester. You can see sparking there. You can see it at other times as well. Get that spark loss fixed. I am pretty sure that is also the clicking or snapping sound.
@TightlineTV 11 ай бұрын
Good eye! Wow haha
@austinbraswell1543 11 ай бұрын
It looks like thats just a metallic label that has the part number on it thats flapping and catching the sun as it turns over
@Mjones8383 11 ай бұрын
As long as you're with 15 psi and above 90 you're golden
@Tyfixisall 11 ай бұрын
I use the square ones but you have to spin them to where they are vertical in the water pickups.
@MrBdogg317 6 ай бұрын
I just brought an 03’ skeeter zx225. And when I got done going through the boat I turned it on and it started peeing. I was like a kid on Christmas morning 😊
@rjfussell 5 ай бұрын
that isn't a thermostat issue,that just shows the impeller is good,you need a laser thermometer to check heads for thermostats opening at the block on both sides.
@chrisbarber1020 11 ай бұрын
You deserved a break on the motor after the Bass Cat lol good for you dude!!!
@M.Bassin 11 ай бұрын
Double dose of quickcleen and some ethanol free fuel then go run it hard. It will thank you for it.
@victorremick9721 11 ай бұрын
Your first test the motor was dry meaning there had been no fule run through the motor. you could spray a lub in each cylinder let it sit for a hour or so turn the motor over with out the plugs in it to blow out any exses oil put the plugs back run the motor for 10 min then check the compreson again i am sure it will come up around 10 more lbs in each cylinder
@randybarger8649 10 ай бұрын
I I’m sure needs plugs that’s good moter I run the pro xs 250 maybe change lower unit oil and send it
@chrisbruce7594 11 ай бұрын
The extra water coming out is normal. Your good
@jeffp9146 11 ай бұрын
Same engine. I tested compression with a harbor freight tester. Got 95. Took it to a shop and it tested 135.
@backyardfishing1 11 ай бұрын
That's weird i use the square ones all the time and never had an issue but that is on a 90 yamaha and a 70 evinrude. Glad to see you got it figued out.
@dhooter 11 ай бұрын
I run Penzoil. Has all the same ratings as quicksilver. Never had any issues
@paulmanzone8373 11 ай бұрын
I've seen extra water like that be part of exhaust, but I could be completely wrong, been wrong before
@SneakerShow24 11 ай бұрын
My 2021 mercury does the same thing with the water coming out of it in different places. It’s normal. Don’t stress it
@nikkiblack5073 11 ай бұрын
Wow what the muff was that 😂😂😂
@kencleg7721 11 ай бұрын
I use marval mystery oil o bout 1 oz in a 6 gallon tank works like a champ a little extra oil that burns
@mypie3301 11 ай бұрын
I owned this same engine, the coil packs and plug lines are notorious for cracking (microcracking ). they will shock you when touched in run mode. They also short while running and seems like your running out of fuel. Just an fyi
@Precisionreelworks 11 ай бұрын
I like the muffs that have a crossover hose and will inject water on both sides
@henrycole8705 Ай бұрын
Thermostats should be checked for proper operation by taking them out. place them in heated water with a thermometer and see what temp it opens at. flush cooling system without thermostat as well. Note water flow, check pump vanes every year after winter. A simple maintenance issue.
@TheTermite74 10 ай бұрын
I believe you have the installation manual. You might want to try to find an owners manual or even better a service manual
@machew2009 11 ай бұрын
If you rotate the rectangle part of the muff so the long part goes up and down on lower they should work just fine that is what I do and works just fine