Tillotson 212 unboxing and total governor removal/beast!

Рет қаралды 19,905

3 жыл бұрын

Tillotson 212 unboxing and total governor removal
Unboxed the Tillotson 212 and removed the internal and external governor.
Used a 1/4-20 bolt to plug the holes after removing the hardware.
Looking at the differences between the Tillotson and the Predator 212.
Music- Scandinavianz - Sunset Beach _ (Travel) Background Music No Copyright-o8MRY2xDZlY
Instagram - doubledown555black66
__________________________________________________
Parts used
engine - 212cc Tillotson Hemi Engine, Electric Start
www.gopowersports.com/212cc-t...
*********Disclaimer*********
Please do not try to re-enact or recreate anything you see in these videos.
Black66 does not take any responsibility for injuries or equipment failure created by doing so.
ALL BLACK66 CONTENT IS FOR ENTERTAINMENT PURPOSES ONLY.

Пікірлер: 141

@tennesseesteve7949 2 жыл бұрын

I use my deep freeze too when my work bench is full. I put scrap cardboard on it. My wife would kill me if I scratched the top of the freezer. lol. Good video, thanks.

@Black66 2 жыл бұрын

Thanks, lol. Mine is already scratched.

@Nate-dx6gg 2 жыл бұрын

Hey do you think this engine would be good for a beginner or should I go with a more low power engine

@marquislewis1767 Жыл бұрын

I have 212 tilly with go power sports stage 1 kit.(header pipe, filter and adapter, larger jet). If i delete governor will the flywheel hold up? Will i see any gains?

@guneriusisland2295 Жыл бұрын

Took all the governor on that Tilly but what do you do for throttle when you take that out going to use it as a mud motor

@Godisgreatandgood777 2 жыл бұрын

what size did you use for the spark plug ?

@cesarborunda5224 Жыл бұрын

Where can I get a 212 hemi predator I live in Cali and I want to get my hands on one any ideas on where I can pick one up

@ericalvarez3294 4 ай бұрын

Any suggestions. I have same engine and decided to upgrade to juggernaut and mikuni carb. Engine ran for about 30 seconds then locked up. Have no idea what to do next? Any suggestions for unlocking engine.

@ronaldscruggs2699 9 ай бұрын

What rpm is a stock tillotson 212e governed at from the factory? Can't find this info anywhere.

@itsme5279 3 жыл бұрын

You can also just take the crankshaft out and remove the gear on the crankshaft.

@zuno700 3 жыл бұрын

Can you do a vid on how to connect the wires to start it with the key

@groskreutzzdsinn17 4 ай бұрын

I can't seem to find a video anywhere on keeping the electric start and upgrading to the bullet flywheel made for electric start on the tilly 212's

@Black66 4 ай бұрын

Use a billet flywheel and use this lighting system. It last for days without a charge! kzfaq.info/get/bejne/bZuRpdWrqt2zppc.html

@jonathanzarour1601 9 ай бұрын

I followed the steps and I have a vm22 carb but it won’t start and there’s gas coming out of the air filter PLEASE HELP!!

@elitetoxicity9446 Жыл бұрын

Just got one and did this and the engine won’t start, I’ve got a pull start and did this exactly step to step I do have the old carb on the engine with a staged exhaust. I did not take the coil next to the flywheel off because I don’t have the starter. Can anyone give me some help I have a flat slide Mikuni arriving soon just trying to get the engine started without it for now

@trevor7954 Жыл бұрын

is there another way to get that top pin out without cutting it? for the governor removal

@GliblyUnited8billion8 2 жыл бұрын

What size is the driver nut bit peace? you used for the flywheel because my crow bar is not doing it😂

@micksmixx75 2 жыл бұрын

What does removing that do?

@johnsmith-zd5he Жыл бұрын

Been a big fan of yours man! Was wondering if the 252 rattlesnake cam would be an upgrade in a tilly 212 along with an 8 degree keyway, mv22 ,mikuni, and header pipe over the stock cam while i have it apart to take out the governor??

@Black66 Жыл бұрын

Thanks! Yes, a 252 cam would be an upgrade. I measured the cam that cam out of the Tillotson 212 and it doesn't have any more lift than a stock Predator.

@johnsmith-zd5he Жыл бұрын

@@Black66 Awesome!! Thanks dude!! Keep the great vids coming! My young boys and i always tune in to learn more, and get to see the minis go 70+ mph haha!!

@Ghost88890REAL 2 жыл бұрын

Good video, I am working on an ATV that the engine blew up and I want to switch that rusted 150cc engine to a 212 predator/tillotson (or see if I can find a higher output) and I'm looking just to make it work and not burn rubbers on it. You think a 212 tillotson would do?

@Black66 2 жыл бұрын

Ya, it would be awesome on there !

@mr.braapalicious 2 жыл бұрын

What are the sizes of screws you used to plug up the 2 holes? Thank you. Great video..

@Black66 2 жыл бұрын

I used a 1/4-20 bolt. If you can get one with self-tapping threads it even makes it easier.

@mr.braapalicious 2 жыл бұрын

@@Black66 thank you!

@igokarts4510 2 жыл бұрын

I have two Tillotson 212's in two identical go karts. Both have stage one kits with governor intact but zip tied. Kart #1 will hit 5000+rpm without a governor surge. More so I ran out of pedal. Kart #2 will governor surge at approx 46-4700rpm. Kart#1 has been rolled and at one time I had to put pushrod back under rocker after it rolled. It runs like a scalded dog but for some reason it's identical twin seems to be lacking. Any thoughts or suggestions?

@Black66 2 жыл бұрын

That governor is still having some effect on the throttle, obviously . How about totally disconnecting the connection between the governor arm and the throttle linkage. I had governor surge on mine with the zip tie trick, until I totally removed the linkage that connects the throttle to the governor arm. I ran the cable direct to the carb. After I did that the engine ran like kart 1. It would rev with no surge.

@igokarts4510 2 жыл бұрын

@@Black66I may try that! I think the governor deletes and mikuni carbs are gonna be coming soon

@Black66 2 жыл бұрын

@@igokarts4510 The VM22 will wake those tilly's up even more. Easy carb to tune too

@igokarts4510 2 жыл бұрын

@@Black66 I've got a resto/mod kart I'm currently doing. It's a predator 212 with a dynocams CL1 cam, header pipe. I just ordered a mikuni vm22 for it. Any suggestions on jetting or do you think I'll be ok stock?

@Black66 2 жыл бұрын

@@igokarts4510 I would start out with a 115 or a 120 jet . The stock jet is usually to small

@benhille4041 2 жыл бұрын

So does the governor come installed on the engine when you get it?

@Black66 2 жыл бұрын

Yes

@herecomesdoublej 2 жыл бұрын

What are the torque specs on the bolts for reassembly?

@Black66 2 жыл бұрын

All the specs are on the Tillotson web site. Here is the link tillotson.ie/resources/

@Spacecruizer203 Жыл бұрын

god only know i have so many questions for you right now mr black66

@brianscollon4046 Жыл бұрын

Were due you get the bolts to put in the plugs

@Black66 Жыл бұрын

Any good hardware store with a bolt bin.

@toddsanford7757 5 күн бұрын

the throttle linkage on this motor is so janky ,, there is really no spring pulling the carb closed. there is one spring that pulls is mostly closed. i've never seen such a crazy linkage setup before. anyone have any great mods to deal with this?

@Black66 4 күн бұрын

Yes , kzfaq.info/get/bejne/ebFko5Cavrrbdps.html

@toddsanford7757 4 күн бұрын

@@Black66 i guess im gonna have to buy a torque wrench, 21 mm socket, 2 half inch 1/4 20 with copper washers, lol

@scottdunkirk9938 Жыл бұрын

Stock valves springs with governor Delete? Sounds great

@Black66 Жыл бұрын

The Tillotson comes with 18lb springs! Thanks for watching and check out the playlist for more combos with this engine.

@hughjass4147 Жыл бұрын

@@Black66 is it worth getting better ones

@Tyler-xh2sg Жыл бұрын

Why do you have to take the coil off?

@Black66 Жыл бұрын

To show how to set the coil gap. 👍😀 Thanks for watching!

@TheBest-ns1wb 2 жыл бұрын

What’s the top speed of it with the gov removed?

@Black66 2 жыл бұрын

Check out the Tillotson 212 Doodlebug playlist. It shows many different combos with the Tillotson 212 kzfaq.info/get/bejne/hNWmZNt6lde0qKM.html

@kadar5551 2 жыл бұрын

Take a drink every time he refers to little parts on a little engine as a “Beast”

@Black66 2 жыл бұрын

Yes, it worked ! I got you to comment 😀

@l.a.m7645 3 жыл бұрын

The 2 bolts to plug top hole and governor whole what sizes do I need so I can pick them up at hardware store?

@Black66 2 жыл бұрын

I used a 1/4-20 bolt. If you can get one with self-tapping threads it even makes it easier.

@l.a.m7645 2 жыл бұрын

@@Black66 Go power sports sells them $1.49 each I got 2.

@Black66 2 жыл бұрын

@@l.a.m7645 Good deal!

@l.a.m7645 2 жыл бұрын

Do I need to use washers?

@Black66 2 жыл бұрын

@@l.a.m7645 No, put a bolt in it and your good

@DJ_CAZZARELLI 2 жыл бұрын

Did you upgrade the flywheel?

@Black66 2 жыл бұрын

I added a billet flywheel in later videos.

@omarbautista7104 Жыл бұрын

Would the engine internals hold up after I removed the governor in a tillotson 212

@Black66 Жыл бұрын

Mine has held up for a couple years now.

@omarbautista7104 Жыл бұрын

@@Black66 wow, that’s great is it stock?

@Black66 Жыл бұрын

@@omarbautista7104 I have a couple. The most recent is on the Mega Moto 212.

@Black66 Жыл бұрын

They are tuff engines,But there is no guarantee on any of this stuff. Yours might last five years and mine could blow up tomorrow, You never know.

@eyehearther111 3 жыл бұрын

I need to get me one of those.

@Black66 3 жыл бұрын

Ya, get one

@elijahkeeper636 3 жыл бұрын

Not as simple as that they never have them you can try

@dturfmadeit1518 3 жыл бұрын

I jus bought one 6 days ago

@4687878 2 жыл бұрын

I thought you were going to leave that gov gear washer in the engine,...wheeew !!!

@Black66 2 жыл бұрын

No, it’s all cleaned out

@xchoatic_venomx744 3 жыл бұрын

Recently been debating heavy on if I should get a predator 212 or the Tilly. I’m not really looking to abuse the engines just wanna know which would you truly recommend as a first engine I really like the vids you do and few people on here I’d trust with any advice on it?

@Black66 3 жыл бұрын

Thanks! A Predator is just fine . They are durable enough and you can do a lot to them . A Tilley is really good to , especially if your gonna do a radical build . The blocks are strong . I would just grab a Predator if I was going to do a basic build or even leave stock .The good thing about a Predator is if it blows up its cheap enough to replace .

@xchoatic_venomx744 3 жыл бұрын

@@Black66 thank you so much for the feedback ! Just one more thing if I may... what if I’m trying to get good performance with just the carb and exhaust set up?

@Black66 3 жыл бұрын

@@xchoatic_venomx744 Adding both will improve performance

@xchoatic_venomx744 3 жыл бұрын

@@Black66 thank you once again truly I’m probably gonna go with the tilly !

@Black66 3 жыл бұрын

@@xchoatic_venomx744 Good engine , especially if you are going to end up modifying it later , and you not so worried about the price .

@davidmorgan8612 7 ай бұрын

With no audio on most of this I don’t know but I hope you cleaned that out before putting it back together.

@Black66 7 ай бұрын

Check out the Doodlebug playlist. This engine is alive and well two years later with many videos and part swaps . Thanks for watching!

@RedfishInc 3 жыл бұрын

I take a drink everytime you say beast... I wasted.

@Black66 3 жыл бұрын

Cause it’s a beast!!!

@eyehearther111 3 жыл бұрын

😂

@Black66 3 жыл бұрын

Actually, it was a beast, but then I added this cam that I don't like too much, so now it's not such a beast anymore. I might have to change it out.

@GPMAX01 3 жыл бұрын

@@Black66 which cam sucks?

@Black66 3 жыл бұрын

@@GPMAX01 There all good. The 265 is the best. That is my favorite drop-in cam so far.

@JLeezy864 3 ай бұрын

Awesome video but audio cut out for most of the video.

@Black66 3 ай бұрын

yeah its an old video, I need to redo it. . i have quite a few more newer governor removal videos on the channel. kzfaq.info/get/bejne/ebFko5Cavrrbdps.html

@eyehearther111 3 жыл бұрын

Has it been tested yet on any of your toys?

@Black66 3 жыл бұрын

Ya, I went out today with it .

@Black66 3 жыл бұрын

I think it will really make your bike fly

@eyehearther111 3 жыл бұрын

Yes!! Thatd be awesome! Took my bike out after the storm yesterday and got it all muddy, fun times. Upgrade would be better lol.

@Spacecruizer203 3 жыл бұрын

so is it more torque or top end

@Black66 3 жыл бұрын

I think it has both. That Tilley runs good

@Spacecruizer203 3 жыл бұрын

@@Black66 sounded like a drag bike good footy

@Black66 3 жыл бұрын

@@Spacecruizer203 They run by all the time

@Spacecruizer203 3 жыл бұрын

@@Black66 sweet man what's next mabey a lil chopper action

@Spacecruizer203 3 жыл бұрын

@@Black66 I'm sending that 12 tooth back it turned my bike into a flintstone mobile lol the old rusted five year old 11 tooth gets me going idk what rear sprocket would give me more torque on this lil 80cc what's the best combo

@rico7844 3 жыл бұрын

Can you put it in the Coleman

@Black66 3 жыл бұрын

Ya, I might do that . Just not sure which one . The little one or the big one

@rico7844 3 жыл бұрын

@@Black66 do the cc100x one ,because I got a cc100x 😂

@Black66 3 жыл бұрын

@@rico7844 Man I really do want to put it on the cc100x . That thing would fly !

@rico7844 3 жыл бұрын

@@Black66 are you going to some a video cause I’m thinking of a buying a tilotson

@rico7844 3 жыл бұрын

@@Black66 sorry to disturb you, but do you have any social media because I want to send you a video of my bike because im trying to start it up but idk what going on , I chang the motor to a new one,bought a mikuni carburetor,added some oil, there gas inside everything is good but idk what going on