Tips You Need Before Building A Roll Cage

  Рет қаралды 7,495

FDF Raceshop

FDF Raceshop

4 ай бұрын

We lay out some important tips when installing a roll cage in your car. This specific cage is for Paul at Grassroots Performance. This is a full FIA rated cage and is designed for rally racing. But, these tips apply for any sort of cage that you are building or just installing.
Socials:
/ fdfraceshop
/ fdfraceshop

Пікірлер: 17
@BullyBreaker
@BullyBreaker 4 ай бұрын
Good information on leaving things malleable and out of the car for clearances.
@aussietruckphotosandmodels8510
@aussietruckphotosandmodels8510 4 ай бұрын
As someone that builds FIA spec cages. We always take the roof skin of so you can weld the top of the bars. You can also use foot plate boxes, which can also be used as strategic strengthening plates if you think a head. Don't reuse bars that you have stuffed up, unless you can clear cut past the ends short of the old welds..... FIA Schedule J ....Every joint must be fully welded all the way round. You can step the cage out from the body enough to get a welder in and attach the cage to the body with gussets which are the same thickness or thicker than the tube wall..... What you have there will not pass FIA spec....I can send you a copy of the FIA roll cage spec if you can't find it....
@DirtyGarage
@DirtyGarage 4 ай бұрын
That's what I was going to say. It's nice to have a tight fitting cage that follows the contours of the body, but you have to build some tolerance in to allow for it to be fully welded, especially at the base plates. Any incomplete weld will fail a logbook inspection.
@SteveBrownRacing
@SteveBrownRacing 4 ай бұрын
Incomplete welds is a fail in every series I've ever been involved in. So don't turn up to events with NASA, Lemons, Champ Car, or AER and expect to run. I think the only exception I'm aware of is for GT3 cup Porsches that for some reason don't need fully completed welds.
@aussietruckphotosandmodels8510
@aussietruckphotosandmodels8510 4 ай бұрын
@ stevebrownracing.... It's because of the carbon composite structure. I'm lucky enough not to have the kind of budget to be involved with them.. Also.. McLarens fall into that category for the same reason... I'd also like to say that I think FDF Raceshop have a great channel, backed up with fantastic products.
@DingDongDrift
@DingDongDrift 4 ай бұрын
great tips, i'm waiting for my cagekits cage to arrive soon.
@thekevinsoucie
@thekevinsoucie 4 ай бұрын
If you guys are in Texas or surrounding, check out turn 5 fabrication for a cage! Great video
@Thee_Snow_Wolf
@Thee_Snow_Wolf 3 ай бұрын
1:34, From FIA Appendix J "Guidance on welding. These must be carried out along the whole perimeter of the tube." How did you fail this when doing the main hoop brace? This should be blindingly obvious you need to weld the bars fully. Your order of work prevents this.
@mathieuberthiaume3982
@mathieuberthiaume3982 4 ай бұрын
Cam the Mannnnnn!
@erikvanvechten1289
@erikvanvechten1289 4 ай бұрын
Gotta tell them you HAVE to weld everything complete. You'll fail tech, and even if you snuck it past an inspector (which you should never do), you're driving a potential pin cushion.
@RKDRIFTZ
@RKDRIFTZ 4 ай бұрын
Good comments so far but also check your reglements regarding cell foot size.. i did my cell in my 370Z according to DMEC spec. :)
@reubenplasencia6530
@reubenplasencia6530 4 күн бұрын
how much for a cage for a 370z? I want one for my Z!!
@williamshelby1041
@williamshelby1041 4 ай бұрын
I like the channel lol
@BB-pf2cs
@BB-pf2cs 4 ай бұрын
I just clicked this. And was very glad to see a 370Z in the first clip! Building a little machine for a weekend drifter down in Australia❤🎉 any advice is very bloody welcome
@zxcvbnm007
@zxcvbnm007 4 ай бұрын
why not cut the roof off, weld the cage and weld the roof back on?🤔
@carlossol999
@carlossol999 4 ай бұрын
5:46 for some vehicles the roof is not easy to remove and it would take additional fabrication to make it look right.
@LuckyFruitRacing
@LuckyFruitRacing 4 ай бұрын
Surprisingly in a lot of instances it really doesn't make it that much easier. Just finishing up a cage in my mx5 and even with no roof and being able to basically build the cage in sections outside of the car, it's all the welding that needs to be done inside the car down low that's the hardest
DIY Roll Cage - Is it Worth It?
23:52
Donut
Рет қаралды 2 МЛН
The Most Important Caster Tips
9:42
FDF Raceshop
Рет қаралды 7 М.
🌊Насколько Глубокий Океан ? #shorts
00:42
I CAN’T BELIEVE I LOST 😱
00:46
Topper Guild
Рет қаралды 58 МЛН
Пробую самое сладкое вещество во Вселенной
00:41
She ruined my dominos! 😭 Cool train tool helps me #gadget
00:40
Go Gizmo!
Рет қаралды 60 МЛН
How to Build a Roll Cage | Notching, Bending & Measuring Tips & Tricks
22:33
Foolproof Methods For Building A Roll Cage | NEW Wheeler Dealers
7:17
Wheeler Dealers
Рет қаралды 97 М.
What Are Swift Springs? Everything You Need to Know...
5:13
Nefarious Racing
Рет қаралды 304
Tips On Setting Up Your Drift Car For Competition
14:50
FDF Raceshop
Рет қаралды 6 М.
Cage Kits roll cage Install/ Who did it better?
28:43
FDF Raceshop
Рет қаралды 40 М.
Tips For Installing A Roll Cage At Home
14:57
Power + Performance
Рет қаралды 10 М.
How To Build Headers | Trick-Tools.com
12:14
Trick-Tools.com
Рет қаралды 594 М.
Roll Cage Installation
21:09
Kiil
Рет қаралды 189 М.
2020 Drift Supra CAD Designed Roll Cage Install and Fabrication
10:01
PapadakisRacing
Рет қаралды 2,1 МЛН
Magirus-Deutz 232 АНОНС
0:58
Иван Зенкевич PRO автомобили
Рет қаралды 1,3 МЛН
БРОШЕННЫЕ АВТОМОБИЛИ В ДУБАЙ
0:39
AblyazovLIVE
Рет қаралды 428 М.
РОССИЯДА МУСОФИР АВАРИЯ БУЛДИ
0:17
Yakka Tv
Рет қаралды 2,8 МЛН