Dang that looks awesome! Wish mine was the flat bottom
@carlkrewler40842 ай бұрын
I was wondering if you have any idea when the " new" flat pans will be available at a retail stores like Home Depot etc. The install looks much less troublesome than a mortar base.
@johndarby21695 ай бұрын
? 1. Why no flashing on the shower pan wall like it shows in the Tile Redi instructions on their website? So just a but joint with no flashing on the shower pan wall is acceptable? The pan you installed doesn’t have the deep grooves underneath that require approx a. 1-1/2” of mortar. Have you changed the design of the pans? Your website still shows the need for a approx 1-1/2 inch motor bed required instead of an application of thinset that was done in this demo.
@TileRedi_US5 ай бұрын
The flashing is an option, in this case we did not use it and only used the MS Polymer (Redi Sealant). Used according to the instructions will also provide a waterproof seal on the splashwall. You are correct, the shower pan installed is a different pan than you may have used in the past or see on our website. It is a flat bottom shower pan (Pro Line) similar to our custom pans and do not need to have the mortar installation filling up the ribs. This is currently available to the commercial market in limited sizes.
@tonycopelyn8730Ай бұрын
In terms of water proofing and longevity; no concerns about installation times…does tile ready have a clear advantage over cement backer board products like USG or Perma and roll on water proofing?
@TileRedi_USАй бұрын
Yes, with Redi Wall boards, you don't need to worry about applying or roll-on any additional waterproofing membrane. No special fasteners are needed either, all you do is screw it to your framing and cap off the screws with our Redi Sealant.
@realdeal415Ай бұрын
These walls are tough I did some tests before installing. I attached a scrap piece to a 2x4 using one deck screw. We could not physically pull the board off unlike go board and cement boards. Also, we glued a butt joint together using scrap and the redi sealant and could not pull them apart after it set. Very tough and easy to work with.
@retiredperson40545 ай бұрын
So why the NEW FLAT bottoms? Why did they switch from the Pans that were webbed?
@TileRedi_US5 ай бұрын
We wanted to find an even easier way to install our shower pans. This is a new design similar to that of our custom pans (flat on the bottom). Our ribbed pans are still available on our website and most retailers.
@WGS11114 ай бұрын
Similar to flat earth eh?
@WGS11114 ай бұрын
The instructions read do not step in pan after setting?
@TileRedi_US4 ай бұрын
You are correct, we will be making a change to that since many contractors and DIY'ers have shown us that it helps in the installation process and does not harm the pan.
@WGS11114 ай бұрын
@@TileRedi_US thank you for sending this.
@dascomp516 ай бұрын
How can I find an experienced installer in Dallas?
@oliviernguyen19424 ай бұрын
i do not find the flat bottom on your website
@TileRedi_US4 ай бұрын
They are not available for sale on our website just yet. We are launching them in the commercial market first.
@carlkrewler40842 ай бұрын
@@TileRedi_US So when would they be available at Home Depo ect. Will the new be as new base be as the solid ?
@Jerrywekar76214 ай бұрын
What type of thinset
@TileRedi_US3 ай бұрын
The installation instructions will provide you with the recommended thinsets. They differ for the wall and the pan.