This is the second one for the basement bat. kzfaq.infoUgkxOuLt8IL_GxhhaK8DBuKEL-zV0UJVpWZn , works great
@carole28355 ай бұрын
Perfect simple explanation, First realised I had a problem when water was running down the brickwork from the overflow pipe outside. I had the opposite issue - too high a water level in the toilet tank. Sure enough the water was spilling over into the overflow tube. I adjusted silver nut/screw as recommended. Thanks Garry!
@650GSF5 ай бұрын
Hi, glad my video was helpful, nice to be able to do these little simple jobs yourself and save a bit of money.
@bethanmiles51262 жыл бұрын
Absolutely brilliant..! Described everything slowly & carefully - I watched several other videos, but just couldn't get it, but I have mended my daughter's toilet all by myself..! Huge thank you!
@watkinwilliams13 ай бұрын
Thanks for the video, perfectly explained.
@danratcliffe48494 жыл бұрын
Thanks for this video. I was able to fix my mom's toilet in less than 2 minutes!
@xeniamadey49143 жыл бұрын
Thanks for this, makes it so much clearer for me and to anyone who isn’t grateful, get a plumber!
@JK-pd7jf Жыл бұрын
Thanks, my over flow pipe was leaking and I think I've just fixed it by tightening the screws on the arm of the float, saving the cost of a plumber and metered water bill!
@billow9721 Жыл бұрын
Great advice thank you!!
@michaelxhermes Жыл бұрын
Great vid, I wasted hours not being able to adjust the screw enough to make the water stop. Once I saw you explain about the use of a screw driver on the end of the black pin I sorted it in 5 mins. Should have watched your vid first!!
@farobenz61443 жыл бұрын
Hi Thanks for the demo. How do you increase the water pressure on this particular fill valve
@tomjohnson681011 ай бұрын
This is very useful thanks. I liked the way you point out the relevant parts when you mention their names and cover the really important stuff like not over tightening on the nuts on the pipework underneath the toilet. Most of the vids on here are for side entry filler systems so not relevant to me. The camerawork could have been in better focus ! However i did like the slower pace so its easier to follow what you are saying. On many other guidance vids the guys talk too fast, or try to crack too many jokes. Then its harder to follow the key points. Unfortunaltey all this was in vain in my particular case as the plastic nut under the toilet was far too tight and far too difficult to reach - due to the toilet bing fitted too close to the side wall. So i'll have to call a plumber and get the whole cistern replaced with a more modern side fed filler pipe. Many thanks anyway for putting this on KZfaq. I did learn some useful stuff !
@stevecross70282 жыл бұрын
Excellent description 👍
@Paintheshed4 жыл бұрын
what did you do apart from talk about the components?
@garylist96 жыл бұрын
very nicely explained thanks. i tried to do mine but i think i loosened the nut on the service valve lol. mine doesnt go exactly straight up a kink in the copper allows for a small adjustment alas i have called my plumber in. think it would of been wise to secure the nut on the service valve with a wrench to prevent any movement. oh well live and learn...
@650GSF6 жыл бұрын
it's a learning curve like everything at first, but once you have done a little bit of plumbing and gain a bit off confidence you will be happy to do these little jobs and save a few quid :-)
@fredshead3956 Жыл бұрын
Hi there i have fitted a side entry fill valve, there doesnt seem to be sealing washer on the inlet union pipe, is there supposed to be a fibre or rubber washer, it weeps a bit i have put a load of ptfe tape round ot, also when it fills up there is a horrible groaning noise for about 15 seconds.....any advice Please Fred in Essex.
@gilormsplay8 жыл бұрын
Job for tomorrow! thanx
@650GSF8 жыл бұрын
+Gil Orms good luck.
@anthonykinrade8642 Жыл бұрын
It will not flow out the cistern if it fills too much! The water will escape through the siphon bottle and into the toilet. That is why there is no visible overflow apparent.
@bobbyvillianueva19633 ай бұрын
That pin that goes in and out with the water level is making a buzzing sound on my toilet when flushing and seems to get stuck in when I flush, I was wondering if I can just replace the pin and is there a spring inside it that gives it its springness
@650GSF3 ай бұрын
Hi, no there is no spring inside it, it just has a rubber diaphragm, it is the water pressure that pushes the pin back out, you can take it apart and give it a clan, that might resolve the problem. If not these are very cheap to replace,
@christophershaw73134 жыл бұрын
Did he actually do anything!!!!
@bhaijaan6558 Жыл бұрын
How do you take out the black pin
@tomjohnson681011 ай бұрын
They are called Cotter pins and they are tricky due to being made of plastic ! You need to pinch the end in with a pair of (pointed end) pliers and then pull !. Its not ideal. Ii wish the makers would use metal pins instead of plastic. Its the same with parts under the engine bonnet on your car. The makers just want to use whatever is chepest for them without thinking of the needs of the end user !
@johntheplumber49363 жыл бұрын
Dunno what plumbers you use that charge £70 for that and to imply that all plumbers rip people off is incorrect.
@Alyzah4 жыл бұрын
Tyson Fury :o
@alanweir35674 жыл бұрын
Was a bit Tyson Furyish!!!
@sarahsomebody8684 Жыл бұрын
Yay Thankyou after faffing about all morning watching other videos which didn’t show the right valve I’ve got. I found yours I was about to throw my girlie spinners out my pram and yay I’ve done it. Thankyouuuuuuuu
@whigwood4 жыл бұрын
I do wish that DIY video makers would write a script first - it avoids a load of verbal waffling.