Derek shows us in part 3 how to ben partial and full pass overs in 15mm copper tube with a pipe bender
Пікірлер: 34
@johngamalier91882 жыл бұрын
Thank you very much. Wish you long life.i have been struggling with bending Passover bend.
@davidstarboo24683 жыл бұрын
By far the best teacher 👍🏼
@0liver0verson94 жыл бұрын
After years hesitating, I've finally ordered a pipe bender. I'll be using your video for reference!
@0liver0verson94 жыл бұрын
By the way, can you recommend the best solder?
@davyogi97963 жыл бұрын
Another good video with tips especially marking both sides of pipe for cross over,, I wish you was my instructor when I was training many years ago things like this keeps the skills up cheers
@mohammednadeem72743 жыл бұрын
Another excellent video Derek, a lot of useful information and ways to do the pipe bends. well presented.
@mj0n4id363 жыл бұрын
Great series on pipe bending. So many great tips. Loved it. Absolutely fantastic. Thanks Derek. 👍🏻 Asian Jon. Training.
@poptumsaffi4 жыл бұрын
Excellent tutorial.
@650GSF4 жыл бұрын
good trick useing the solder to check the angles. not tried pipe bending yet but the videos will be helpful when i try it sometime.
@chrisholt24743 жыл бұрын
Brilliant, thank you, regards, Chris.
@monikanader94543 жыл бұрын
Great teacher👍
@ashkanrajabzadeh96324 жыл бұрын
Perfect as usual👍🏻
@cuckingfunt93533 жыл бұрын
Not perfect, but not a million miles out.
@1Monaghan3 жыл бұрын
Passovers can be frustrating. Lots of extra scrap in the bag mind you. We call them "trophys" when we mess a bend up. Putting 4,5,6 bends on one 3m pipe can be fun.
@1Monaghan3 жыл бұрын
Whats your thoughts on using plastic pipes hep2o etc on central heating systems? It must he so much easier to install in an occupied house with furniture etc. I think there are regs stating no plastic pipework a minimum of 1m from the boiler but it might be different for different boilers.
@tomkatgastraining3 жыл бұрын
Lee Monaghan hate plastic pipe needs scraping. Most boilers are 1 m away before you go to plastic but a few are 600mm. The reason for this is because the boiler could dry fire and melt the plastic pipe if you didn’t know. 👍🏻
@paulbutcherlucasskegness50993 жыл бұрын
How many degrees for small items medium items and large items for the crossover currently doing my plumbing and seems to be 30 degrees for small 45 for medium and 60 for big
@rafidali79208 ай бұрын
Excelent
@vladimirstafasani46303 жыл бұрын
Great Video Derek thank you very much👍 What’s the best pipe benders? Trying to get a pair but not sure which one to go for
@tomkatgastraining3 жыл бұрын
Hilmor are my preferred benders but any you can get are ok 👍🏻
@vladimirstafasani46303 жыл бұрын
Thank you I’ll try them 👍
@Ray.8422 жыл бұрын
Rothenberger robend 4000 is by far better than any other pipe bender 😉
@gbtalk55504 жыл бұрын
Could you show how you would bend a 90° bend say from the floor to a specific height to e.g. 1 meter to the gas cooker connecter or is as simple as measure 1m +150 for the bend
@tomkatgastraining4 жыл бұрын
With the information in the 3 videos you should be able to do bends at any length you just need to put your measurements in instead of the 150 l hope that helps and thanks for watching cheers
@Smart_fix3 жыл бұрын
Hi Tom thanks for informative videos but my question is when we work on site or houses with long pipe is it easy as you doing? Regards Fred 👍🏼
@tomkatgastraining3 жыл бұрын
Yeh you just find space to do it
@davidjingga83562 жыл бұрын
Hi, does anyone know how to bend flat copper pipes? I understand I'd have to stuff the flat copper pipes with, like, fine sand so that kinks won't form when bending. But is there a specific tool to bend flat copper pipes with?
@MarcusT863 жыл бұрын
I'll be honest, and not that I don't completely respect your work and the knowledge you're passing on mate, but I thought it would be way more technical than those thick, roughly-marked Sharpie points on the pipe, and using solder as an angle finder mate! haha I am now believing it may be possible for me to try this!
@patricklynch27313 жыл бұрын
Very good, Very clear, Very interesting, I didn't think you head was big, fat or in the way.... Can I ask what brand of benders you use and the blue formers look the business!;)
@tomkatgastraining3 жыл бұрын
They are just cheap ones from screwfix. Only the best for my trainees 😜
@secondchance44983 жыл бұрын
chris Taylor
@CSLopes-sm3oy3 жыл бұрын
Where is the gap between the pipes??
@carzyscenctist2 жыл бұрын
Have you ever encounter a situation whereby you bend the copper and it broke?
@tomkatgastraining2 жыл бұрын
Nope because you use soft copper to bend. Normally copper will only break if it’s hard