Touch Screen on Chrysler 300 C Not Working? Let's Fix iT for $35!

Рет қаралды 25,438

Күн бұрын

Touch Screen on Chrysler 300 C Not Working?
Touch Screen Replacement - amzn.to/3H9Zv2o
Goo Gone Adhesive Remover - amzn.to/3H3KspJ
Razor Blades - amzn.to/3GFJekd
Razor Blade Knife - amzn.to/3COlY24
Touch Screen on Chrysler 300 C Not Working? This video will guide you step by step on what's wrong and how to replace the digitizer screen for your Chrysler 300 C. See the video chapters below for references.
Video Chapters:
00:00 Intro.
00:19 Remove Paneling.
00:39 Remove 4 Screws Holding the Touch Screen to Your Car.
00:56 Unplug the Wired Connectors on the Back of the Touch Screen.
01:07 Remove 6 Screws Holding the Touch Screen.
01:17 Remove the Metal Frame Around the Touch Screen.
01:36 Gently Remove both Ribbon Cables.
02:10 Use a Razor to Separate Digitizer from Screen.
02:39 Remove the Plastic Film on New Touch Screen.
03:08 Place the Digitizer Evenly on the Screen.
03:25 Attach the Screen to the Housing.
03:54 Put the Screws Back On, then The Metal Frame.
04:14 Reconnect Wires and Mount the Touch Screen.
04:24 Reconnect Clock, Vents, and Control Panel.
Amazon's Choice for Drills - amzn.to/3RXWrrY
Milwaukee 9 Tool Combo - amzn.to/3SZ3KRy
18v Milwaukee Batteries - amzn.to/3CrPud6
Square Drive Wood Screws - amzn.to/3TgiStH
Square Drive Bit Kit - amzn.to/3TdforO
Wand Magnet - amzn.to/3TlcO2V
Want to see more videos like this one? You ROCK!
Subscribe here! bit.ly/2YxjHHu
Small Sledge Hammer - amzn.to/3l2qt1b
Fast Lift Service Jack 3.5 Ton - amzn.to/2VhSAyk
Jack Stands 3 Ton - amzn.to/3BNAdSN
Adjustable Wrench Set - amzn.to/3iWwWIi
Metric Deep Sockets 10mm - 24mm - amzn.to/3iQyWSk
Torque Wrench 1/2" Drive - amzn.to/2Wm4ec4
Cheap Ratchet Set with Extensions - amzn.to/3coYuDs
Full Ratchet Set with Extensions - amzn.to/3ptZmfu
Free All Rust Eater Deep Penetrating Oil - amzn.to/3E07ewf
#DIY #LetsFixiT
Camera / Tool Gear:
GoPro HERO8 - amzn.to/3f7VQUO
Gerber Multi-Tool - amzn.to/39iIfqn
*above are affiliate links that support this channel.
PLEASE NOTE: The content on this channel is to help you understand how things actually work and how to fix them, but you are being encouraged to always seek a professional to get the job done as safely as possible. They are licensed professionals. To find a local professional for your problem, please consider visiting: Bark - bit.ly/3sTQpQr
The creator of this content has an Associate Degree in Electrical Maintenance and has been trained by professionals. These videos are not a guarantee on how to fix something and you assume all the risk when you take it upon yourself to solve a problem.
BE SAFE!
And always remember,
Jesus loves YOU!
And only He can solve your biggest problem!

Пікірлер: 79

@deniswauchope3788 2 ай бұрын

Thanks for that clear, concise, well presented guide! I'm doing this same job on my 2012 200S, and you covered everything I needed to know.

@coachsaldana5708 Жыл бұрын

This is the best "How To" video of this process on KZfaq! No one even close. Thank you

@FixiT-Rick Жыл бұрын

Glad it was helpful!

@psychocycledad 3 күн бұрын

I have a 2012 Chrysler 200 with the same issue. Thank you for the video and the link. Im going to try this out.

@IRONSIDES1968 4 ай бұрын

Great video, getting the glue off was a pain. Other than that it went pretty smoothly. You did a really good job on breaking it down to keep it manageable.

@RalphPurificato 11 ай бұрын

Thank You again Fix it Rick, I sent the first one back and put the second one in, in about 20 minutes. And it works. I may have left some protective film on the sides the first time or it was defective. All fixed for about 29 dollars.

@FixiT-Rick 11 ай бұрын

Sweet!!! That’s awesome.

@staceymorgan-green7926 11 ай бұрын

Thank you, very good information❤

@ghostface1888 8 ай бұрын

Thank you so much!

@MISCDesigns 5 ай бұрын

Dude I accidentally let go at the step on 1:07 and it was a whole b*tch getting the screws back into place. Luckily, I was able to apply the new screen successfully. Thank you for this tutorial.

@SLGlass 9 ай бұрын

Thank you so much I love your ending it encouraged my heart where are you located

@MeLawNy 3 ай бұрын

Thank you 🙏🏼

@FixiT-Rick 3 ай бұрын

🫡🐈

@larrywinston2779 Жыл бұрын

Thank you so much. I didn`t need to replace the anything. I imagine most just need to clean the screens, to rid them of all of that gooey glue and replace them. One tip, If I may. Instead of using alcohol, simply apply "peanut butter" to the glue, wait 2 minutes and simply scrape the residue off with a butter or steak knife (with the intentions of not scratching the glass), then dishwashing liquid, then alcohol, or glass cleaner to finish up (that whole process will take minutes, not hours.

@FixiT-Rick Жыл бұрын

Interesting tip, thanks!

@georgethorn2884 9 ай бұрын

Thank you Fix iT Rick. I got quoted $800.00 - $1,100.00 to replace the unit. $35.00 - $800..00 = $765.00 in savings! Time and effort after receiving the digitizer took no more than 1 hour. You Da Man! Jesus Christ loves you too sir! But you already knew that! Amen.

@FixiT-Rick 9 ай бұрын

Appreciate people like you sir! So awesome to hear. Always good to hear someone remind me of Christ! 🛠️✝️

@goodgriefministries Жыл бұрын

wow! great job!

@FixiT-Rick Жыл бұрын

Easy peezy lemon squeezy!

@fitter70 11 ай бұрын

Thanks!

@FixiT-Rick 11 ай бұрын

You bet!

@HH70Chevy Жыл бұрын

Im guessing this will fix cracked screen as well ? Along with changing stations and flickering on its own. Excellent Presentation on changing it out !!!

@FixiT-Rick Жыл бұрын

If your screen is cracked and changing stations by itself, then yes you're right about changing it out. Thanks for the great comment!

@user-sj1mz9qh2y Жыл бұрын

Will this screen and how to video work with a 2017 Chrysler 300 S???

@marcisaacs9407 5 ай бұрын

What size is the screen in inches and could it work for a Subaru 8” in a 2019 legacy?

@Martinez615x 5 ай бұрын

I have an early 2012 Chrysler 300. I bought a 8.4 touch screen of a 2013 and when I plug it in it’s just black. Would replacing the screen be okay ? Any programing ?

@alanchapa1330 10 ай бұрын

Did it but it has like little bubbles inside, for now is working fine but i am not sure if its gonna last. i think the hardest part is removing the glue, did it with the razor but it doesnt go that easily

@SaltioIsEpic 4 ай бұрын

Does this work with older models such as 2014? I know the uconnects are different but is it pretty much the same ordeal?

@alexcandee9162 6 ай бұрын

Thank you for the great video. I will be performing this procedure when the part comes in. I have a quick question, do I need to disconnect the battery before removing the touch screen equipment? Thanks again!

@FixiT-Rick 6 ай бұрын

Sounds like a good idea to me!

@user-iu8qw4kg4n 6 ай бұрын

How Do I do it

@JosephValenti 7 ай бұрын

Mine is randomly clicking , like touch still works but it still has that seperation that looked similar in this video - is the digitizer starting to seperate the likely culprit of this ?

@FixiT-Rick 7 ай бұрын

The digitizer ribbon cable might be loose

@DemetriusMH Жыл бұрын

Will this help with anti glare coating issues ? I have a 19 300s so anti glare coating is rubbing off in certain areas

@deniswauchope3788 2 ай бұрын

Yes. The anti glare coating beginning to disintegrate is an indication the whole digitizer is failing, so it's time to replace it.

@AmandaVongphakdy 28 күн бұрын

I broke my chord connected off the casing how does that impact it

@FixiT-Rick 28 күн бұрын

Well that would depend. Was it the ribbon cable or a plastic connector?

@larrywinston2779 Жыл бұрын

What do you do if the ribbon cable that was notto be touched comes off? Can I secure it back and plug it into it`s slot?

@FixiT-Rick Жыл бұрын

Yes you can! If the touchscreen comes back online, you’ve found the problem. If the touchscreen does not work, then it’s time to replace it.

@mr.october8420 11 ай бұрын

How would i get back my controls for heated and vented seat

@FixiT-Rick 11 ай бұрын

Can they be controlled from the touchscreen?

@juniorparker9322 Жыл бұрын

would that digitizer work with a 2008 hemi C 5.7L?

@FixiT-Rick Жыл бұрын

No, that model will not work. Here's what I could find that might work for you - amzn.to/43f4QhL

@melindamunoz8271 Жыл бұрын

Hi, my screen touches itself lol. so, this would help? Like i will be listening to music or on a call and my screen hangs up or starts beeping like if I am touching it. You made this look easy!

@FixiT-Rick Жыл бұрын

The digitizers screen needs to be replaced for sure. This was the same problem my friend was having.

@camidecker593 Жыл бұрын

Mine dies then same

@FixiT-Rick Жыл бұрын

The video will help you to replace the digitizer yourself. Simple screws, couple plugs, easy peezy lemon squeezy!

@RalphPurificato 11 ай бұрын

This video gave me the courage to do this. BUT! I have a DVD player. And the bottom of the screen and vent covering was screwed into the DVD player. I had to take out the DVD player to get the cover off. I have a 2013 300. I had to call the dealer to get my model radio to make sure I ordered the right one on Amazon. My old cover cracked all over as I tried to get it off. No glue mess. Installed the new one. Put everything back ok. BUT! still does not work and this time. I can control what has buttons but noting on the touch screen works. So the investigation begins. Thanks for the motivation.

@RalphPurificato 11 ай бұрын

Sorry meant CD player

@FixiT-Rick 11 ай бұрын

Sounds good Ralph! Be sure that the ribbon cable is not loose but all the way in. There may be a little door or flap that holds the ribbon cable in place. I would try those first.

@I.jose7 Ай бұрын

The screen on my chrysler start ghost clicking and its just always clicking things by itself do you think its that same screen on this video that i need to fix it?

@FixiT-Rick Ай бұрын

It’s possible that the digitizer screen is bad. Might need to be replaced.

@redundis579 Жыл бұрын

Mine works but the screen is forming a bubble of sorts under it. It makes it to where it acts as if I am touching it when im not and basically it fights with me whenever I do attempt to touch anything. I previously looked it up, and before I seen this video I found it was de-laminated. Would this fix the issue?

@FixiT-Rick Жыл бұрын

If you replace the digitizer, your touchscreen should work perfectly.

@redundis579 Жыл бұрын

@@FixiT-Rick Appreciate it. One place was wanting $400 to fix it plus shipping. The dealer would replace the whole thing for $600. I did not want to pay either of those lol

@javio.9772 Жыл бұрын

Will this fit a 2016 c? I can't find any info online about it

@FixiT-Rick Жыл бұрын

Use the link in the description to go directly to that digitizer screen. From there, Amazon will ask you make and model car you drive and Amazon will confirm if that will fit your vehicle.

@Sammmismile 6 ай бұрын

Will this work for the 2018 300s or just the c model?

@FixiT-Rick 6 ай бұрын

Sounds like you want to replace the digitizer screen for a 2018 300s just like the C Model? They might be similar, I don't know for sure. But if it were me, I would try replacing the digitizer. Just make sure to verify through Amazon that the digitizer will fit the 2018 300s.

@derrickfesser5077 8 ай бұрын

What if your screen is black but the radio still plays. Would I still need a digitizer or just a need radio

@FixiT-Rick 8 ай бұрын

If the screen is black, it might be a blown fuse or loose connection.

@Tabs9fe-py9if 5 күн бұрын

from where i can buy this replacement screen

@FixiT-Rick 5 күн бұрын

Touch Screen Replacement - amzn.to/3H9Zv2o

@luizh948 3 ай бұрын

Hello, I'm from Brazil, I have a 300c 2012. my screen cracked. Do you know how to change??? Is there anything else to do or can I follow the video? great content thanks

@luizh948 3 ай бұрын

Maybe my car is older than the one in the video. the back of my screen has different inputs. And here in Brazil it is very difficult to find this type of parts for this car. There are some others that use the same screen but the background colors are different

@FixiT-Rick 3 ай бұрын

If the digitizer screen gets replaced, I believe your problem will go away.

@anthonydemarco9936 Жыл бұрын

My actual screen is cracked , does the digitizer help with the screen or is that a seperate part that needs to be fixed?

@FixiT-Rick Жыл бұрын

I would remove the digitizer just to see the crack is on the screen. If you find the screen is damaged, the whole thing needs to be replaced.

@Texaco28 Жыл бұрын

Mine is 2011 is it same thing?

@FixiT-Rick Жыл бұрын

The link back to the digitizer screen will ask what type of car you have and they will say where or not it’s a match.

@alexvilla4690 6 ай бұрын

i did this and it worked perfectly for the screen but now no music will play

@FixiT-Rick 6 ай бұрын

Might be a loose connection somewhere behind the screen.

@HDSwiftty 7 ай бұрын

I did everything but now my screen doesnt turn on..

@FixiT-Rick 7 ай бұрын

I would check all fuses

@georgeaguilar8750 Жыл бұрын

What year is you're car ?

@FixiT-Rick Жыл бұрын

She's 2012.

@ITzTiggaByotch Жыл бұрын

Thanks!!! What if the screen jumps to whatever it wants when on?

@FixiT-Rick Жыл бұрын

You’re welcome! Digitizer screen must be replaced if that happens.