No video
Toyota 4Runner Full Skid Plates 2010-2022
Рет қаралды 3,885
Күн бұрынProtect the undercarriage on your Toyota 4runner with a full set of CBI 5th gen skid plates. Built from 3/16” formed plate steel, these skids will be a great addition to any type of off road adventure. Completely bolt on.
______________________________________________________________________________
CBI T4R5 Full Skid Plate: cbioffroadfab.com/product/5th...
Instagram @CBI Offroad
Facebook CBIOffroadFab
Prinsu Instagram @Prinsuracks
Prinsu Facebook prinsudesignstudio
CBI Offroad fab: cbioffroadfab.com
The Original Prinsu: prinsu.com/
#cbiequipped #thatprinsulife #overland
0:00 - Intro
0:45 - Removing the Factory Skid
2:13 - Installing the Rear Cross Member
3:34 - Front Skid
5:58 - Rear Skid
8:20 - Extra Covers
9:23 - Outro
@smithncompany Жыл бұрын
It appears that the rear skid is not installed correctly in this video. Please correct me if I'm wrong. I just used this video to install my skids and it seemed odd that the rear skid laid on top of the front skid as it creates a lip that will hook on rocks and other things you'd want it to "skid" over. The photos on the cbi website, and other videos I'm seeing including one from runnin4tacos show the front skid overlapping the rear skid, which makes more sense.
@stephenbmorton Жыл бұрын
Agree. I installed the rear bracket then front skid and slipped the rear skid behind the front skid to overlap front to back. It worked with no problem and fit beautifully. I just left enough play in the rear bolts of the front skid to slide the rear skid in place. Once the 3/8 carriage bolts went in that held the rear skid in place for the rest of the bolts moving backwards. The 3/8 x 4 inch through frame carriage bolt on the driver side was a pain. It lands right near the Cat and there is nearly zero room to work. Same with the front through frame 1/2 carriage bolt on the driver side. The kit come with washers in for all the CBI nuts, but I don't see this mechanic using any washers. I would have loved to keep the radator guard. I read somewhere it is used to protect the radator and also force air throught the radator.
@matthewbosma5715 Жыл бұрын
Note: if you’ve done the Tundra steering rack swap, you may run into an issue where the passenger side middle support conflicts with the bolt for the steering rack. Removing a bit of the support (1/2” deep by 1” wide) will remedy this without significantly weakening the support (if at all).
@ruggedindsoup2135 2 ай бұрын
So there is nothing to fill the front gap? What the… ?
@yourdailyblockchain 10 ай бұрын
Super cool - it would be awesome if you had a trans skid plate that was cut to integrate into the stock TRD Pro skid plate. I don't want to lose my TRD skid.
@kBIT01 Жыл бұрын
My kit was missing the 3/8" short carriage bolts and the 3/8" strut washers.
@jaimegarcia213 Жыл бұрын
I wonder if since the 2010 to 2020 4runner are on the same chassis if they will work on my 2012 fj cruiser
@cbiprinsuinstalls Жыл бұрын
We had one person do it. Todd from @fourpointsadventures on Instagram. Shoot him a DM if you have questions about the fit. Otherwise we’ve never tried it.
@jaimegarcia213 Жыл бұрын
@CBI & Prinsu Installs thank you definitely messaging him! 🙏🤙🏼
@Machiwi-vo9nb Жыл бұрын
Is this compatible with KDSS?
@chrisridebike8 Жыл бұрын
Yes
@wnderinbasecamp 9 ай бұрын
KDSS, 2' lift having issues with the front sway bar..treaty oak space adapter OR DR.KDSS sway bar adapter plates (tried both) my sway bar essentially sits on the skid when the valve is open and my passenger tire is on a vehicle ramp. So if ever in motion with the front passenger tire moving higher than the driver side and at a slowish speed it starts to carve into the actual skid. Any solutions?
@MrGuitar808 Ай бұрын
Did you ever find a solution for this? Debating getting Dr KDSS front adapter plates but want to ensure it won’t mess up adding aftermarket skids later on
@wnderinbasecamp Ай бұрын
@@MrGuitar808 should be fine with the Dr. KDSS products (bushing brackets & adapter plates) with the CBI skids.
@MrGuitar808 Ай бұрын
@@wnderinbasecampawesome thanks!
@one_smart_alec 9 ай бұрын
I assume that first plastic piece he removed still gets reinstalled?
@chrisdeantonio1498 4 ай бұрын
Ever get an answer to this?
@one_smart_alec 4 ай бұрын
I don't think they have anything to fix the new gap. Kind of a let down
@terrymessado2468 Жыл бұрын
Does anybody know how much the fulll skid plate in steel weight is?
@jaimegarcia213 Жыл бұрын
From what I've seen it's 50 lbs lighter than the aluminum one! Which I think it's because the steel plates are thinner than the aluminum ones. 180lbs for aluminum complete kit and 130lbs steel complete kit. Based on what I've found online I could be mistaken.
@Don-md6wn Жыл бұрын
@@jaimegarcia213 That's not correct. On the CBI site it says their aluminum plates are about half the weight of their steel plates. But I can't find anything on their site that says what the weight of either is. The typical weight for a set of 3 steel skid plates for a 4Runner is about 150 pounds. Steel rock sliders are about 100 pounds. I have both on order for a 2018 4Runner Limited I've recently purchased. But when they're installed I will lose the running boards (50 pounds) and whatever the Toyota plates that will come off weigh, which I'd guess isn't more than 20 or 30 pounds. So overall I think I'm basically adding the weight of a normal adult male passenger, maybe 175 pounds, to the vehicle.
@ryanm4013 Жыл бұрын
@@jaimegarcia213100% completely false. The entire point of aluminum skids is that they are LIGHTER than steel, even though they are thicker.
@johngriego9612 Жыл бұрын
I have full steel skids/gas tank skid and sliders and it added around 400lbs
Sunroom Studios
Рет қаралды 2,1 М.
Team4Runner
Рет қаралды 3,5 М.