Thanks for the video. Good ideas! nice to see the trial and error. I will tackle this job on my hilux surf soon.
@gasgiant71223 жыл бұрын
Great video & great music, reminded me of The “A” Team👍👍👍
@tvalem3 жыл бұрын
Great video and very informative! I’m glad I watched to the end thanks buddy!!
@vincegrandon14004 жыл бұрын
VERY GOOD DESIGN AND YOUR VIDEO WAS VERY INFORMATIVE THANKS FOR SHARING IT. I WILL HAVE MY WELDER REPRODUCE IT FOR OUR SHOP. THANK YOU FOR SHARING.
@Saltbox97 Жыл бұрын
That worked great. Second design that is. Well done.
@likits19992 жыл бұрын
If you only knew how I removed mine as an emergency. No puller tools at all and it was so easy. It took me less than a minute. Toyota parts are beasts!!!
@scooterman1965 Жыл бұрын
Please tell us.
@dc57234 жыл бұрын
Awesome design!
@michael1842722 жыл бұрын
Very interesting and informative... One question..can you share the spacing measurements for drilling the 4 holes into the plate that bolts onto the 4 bolts in the bearing housings Thanks
@garykent81935 жыл бұрын
Your 1st project would have worked perfectly with more patience. I work with pullers all the time at my job. The one thing I have learned is never, never, never use a impact on a puller!! You will strip the threads. What I would have done since you have Mig welder is get a good size steel rod or bolt and weld a T-handle to the puller bolt. Also make sure the puller bolt is a hardened bolt with fine thread. Also support the brake plate so the axle hub can push through freely somehow. I thought you had a good idea!!! Oh and before I forget always use shaft saver spacers between the puller bolt and axle end!!
@theotherguy30835 жыл бұрын
Thanks for the advice!!!
@rweems2402 жыл бұрын
@@theotherguy3083 can you give me your deminsions for your tool, thanks
@davidparker9676 Жыл бұрын
The other problem was the type of material of the bolt and nut were too soft. The hydraulic press option is better if it is available.
@mauroherrera52814 жыл бұрын
Thanks for the Video! ✌👍
@williamwhitehead83625 жыл бұрын
You can cut tube 2 or3" off and be maybe better, to fit press?
@J0Gu74 жыл бұрын
Awesome job
@rameshghosiya11825 күн бұрын
What is the reason and benefits of re-welding by slotting inside the plate?
@panchoflores65903 жыл бұрын
Good vid why don't you make some to sell cheaper than the others??? Question other video when disconnected break lines do you have to do something especial to bleed lines due to the abs system verses none abs.
@jamiefitzgerald68404 жыл бұрын
What size pipe
@babeeso5 жыл бұрын
what dimeter of pipe
@dennisranck16135 жыл бұрын
Great, if I had a welder, that would be something worth checking out. But as always, a good video. Thank you.
@paulodias57146 жыл бұрын
otimo video gosto muito dos seus videos principalmente as ferramentas pena qe no meu pais as ferramentas custam muito caro
@donaldpainter9562 жыл бұрын
I don't subscribe to many people at all but you are down to business to get the job done so I'm a subscriber now I hope to see more cool video from your shop
@angelcatalan73766 жыл бұрын
nice job
@TimmyTonTon4 жыл бұрын
will you rent out this tool?
@vincewhite47454 жыл бұрын
Thanks!
@edwinthetechnician65784 жыл бұрын
I custom made my own tool as well to replace the bearings on my 4runner how ever I went with a more sophisticated built I went to my local junkyard took a grinder with me cut off half of the rear end axle and made my custom off of that it’s amazing!!!!!!!!!
@philipphillip3 жыл бұрын
Thats what I was thinking too, much be easier just to weld the flat steel plate on top.
@edwinthetechnician65783 жыл бұрын
@@philipphillip definately! I powder coated mine and it looks amazing!
@markstevens17292 жыл бұрын
Not the most eloquent dismount in equestrian history, but got the job done.
@stevanrose74392 жыл бұрын
I bit the bullet and bought the tools to pull axle bearings. And I bought a new rear axle bearing for my truck. And replaced the bearing. Therefore leaving me with the old bearing that I’m going to weld a pipe on it and have another puller. Then I’ll probably sell the one I bought.it is a universal puller for many bolt patterns.
@zimarokas3 жыл бұрын
Good job im suscribed
@eddvale28054 жыл бұрын
What is the measurement of the pipe and the diameter? I’m thinking of making this tool. This looks ridiculously easy to make rather than buying it.
@AccuracySpeaks2 жыл бұрын
Kind of like the most important factor of the whole deal huh??
@DamionStLouis5 жыл бұрын
Pretty cool! I wonder if you could just bolt the backing plate to the cross brace of the press? I'm gunna find out soon.
@davidparker9676 Жыл бұрын
Pinoy power! You got it done with materials and tools you had on hand, good job.
@theotherguy3083 Жыл бұрын
I am not philipino
@davidparker9676 Жыл бұрын
@@theotherguy3083 Sorry, I made the assumption. You look and act like many Filipinos I know. Good job making your own special tool anyways. You got it done without spending extra money to buy a special tool.
@abboudabudafair14842 жыл бұрын
Very innovative and helpful... perhaps if you shortened the pipe a little, it may be more easier in handling and pressing it in/out.
@dtc2275 жыл бұрын
Can you post the dimensions of your tool please? I can fabricate this as well but I need the measurements. I also have a 2000 Tundra but it only has 158,000 on it currently. Rear wheel bearings are toast on both sides so looking to make this tool to save time and money. Thanks for making the video btw.
@WhatAmIGonnaGet5 жыл бұрын
Thanks for the tutorial. The bolt-pattern size for the plate at the end would be helpful. I would like to machine mine and get it all ready while it's cold before I do the job.
@J_Whitley9874 жыл бұрын
For future reference it’s 3.5”x3.5” squared with 1/2” holes but can over size if desired.
@WhatAmIGonnaGet4 жыл бұрын
@@J_Whitley987 I think I got a 2" standard pipe, and found some flanges laying around in a scrap yard. Look like kind of standard stuff. In case anyone wanted to throw something together. We have lathe, were able to touch it up - but I do not remember actually needing it. The holes in the existing flanges were over-sized on what I found, so it worked.
@brucetjivee68922 жыл бұрын
How to replace car joint
@donaldpainter9562 жыл бұрын
For the most part toyato makes their cars and trucks easy to work on but this rear bearing is a bear and for some reason those parts everyone says to cut off and replace are not available in our area so I'm trying to do it with out cutting anything
@hunterbutler5081 Жыл бұрын
need some sort of protector for the teeth at the end of the axel if you damage those you wont be able to line them back in the axel housing grooves that fit on the teeth
@ex8280Ай бұрын
Even if you bought the bearing puller, and a presser, its still cheaper than going to a mechanic.
@williamwhitehead83624 жыл бұрын
Now you can clean up the welds and paint it and then you can use it again when you need it
@davidteixiera83984 жыл бұрын
Can i borrow dat one. Awesome I'm going to make one now thanks guy.
@zac86064 жыл бұрын
What size of piping is that?
@mcozpda33924 жыл бұрын
i think is 3' X 3'' ... and good wall .. cheers
@TasmanianHillBilly2 жыл бұрын
I made one very much like this one. Didn't work for me, even with a 12ton press. I had to head the inner race of the bearing to red hot and press it while hitting the axle with a hammer.
@mcozpda33924 жыл бұрын
the measure tube is 2 1/2'' X 36'' .. or 2'' X 36'' .. i have a 4Runner 05 wt ABS .. Cheers .. and tanks for sharing and help ..
@KIKOANGELESPARZA4 жыл бұрын
What is the distance of the 4 small holes from center to center if available please,thanks.
@mcozpda33924 жыл бұрын
@@KIKOANGELESPARZA simple , yo saque las medidas del nuevo que voy a poner , hice una plantilla y de ahi a la placa .. empece con un punto y broca chica a baja velocidad y asi sucecivamente asta llegar a la medida deceada .. saludos y espero le sirva compa
@rontollison8673 Жыл бұрын
@@KIKOANGELESPARZA that is my ? also. i have a 98 4 runner got to replace the bearrings
@aaartur4 жыл бұрын
Hi, I have to make one of these, can you please tell me dimensions of the poll? lenght and diameter thanks
@carlsflh4 жыл бұрын
the pipe has the dimensions written on it 2"dia. .095 wall thickness and 36"long you will need to adj. the length for the length of your axles
@KuvHlubStephanie5 жыл бұрын
Haha, did I just heard my Hmong brothers said, "turn it off"? At 11:50😂
@jimmiethomasyazzie16346 жыл бұрын
YOUR ARE AWESAME!!! HOW LONG IS THE PIPE AND FOR WHAT YEAR TOYOTA PICKUP??
@theotherguy30836 жыл бұрын
Jimmie Thomas Yazzie about 2 to 3 foot. I don't have the measurement at this time. It is for all 4runners, Toyota pickups, 1st gen tundra , and tacoma
@rubenramirez21913 жыл бұрын
Hey man looks nice.. you should give us the size or dimensions of the pipe, length of the mounting bottom plate with center holes dimensions. 😭
@yogaobmale8498 ай бұрын
coupling nut about 2 1/2 inches long will do the job no press nedeed
@philipphillip3 жыл бұрын
Im tired too!
@candeffect4 жыл бұрын
Try welding 3 nuts together instead of using one to prevent stripping the threads. There is a video showing a guy holding the brake housing while hitting the shaft end on plywood until the bearing comes out.
@nigelmahood2310 Жыл бұрын
I used the plywood method, worked great!
@chaolee49985 жыл бұрын
brother if you live in Mn , I would like to borrow it.. asap..let me know
@theotherguy30835 жыл бұрын
Lol. I live in California
@MinhBui-ni1by6 жыл бұрын
Very nice. Now I know where I can borrow one lol jk
@ricqik5 жыл бұрын
As much as you tinker, where's your press? Edit... Nvm, you do have a press.. lol
@theotherguy30835 жыл бұрын
I have a 12 ton press. Gonna up grade to 20 ton soon.
@Walkeranz Жыл бұрын
14:40
@elreycosa2 жыл бұрын
cant you just get a puller on loan from the auto parts store ?
@theotherguy30832 жыл бұрын
If they have one
@user-ij4rr8ew7t5 жыл бұрын
чизбургер ноу
@theotherguy30835 жыл бұрын
I dont speak Russian
@marcomtrujillo18894 жыл бұрын
This tool will not work if your truck has abs. It needs to be about 2 in wider at the bottom to fit the abs barring
@theotherguy30834 жыл бұрын
My truck has abs. Lol
@mcozpda33924 жыл бұрын
over than 2'' in .. go for 2 1/2 '' X 30'' ... no more no less .. and if something extra ..
@user-ij4rr8ew7t5 жыл бұрын
I o naigaft af-af-af страшная отдышка 😥😥😥😥😥😥😀😀😀😀😀
@luiscardozo0000 Жыл бұрын
mechanics and welders dont mix...leave the job for a mechanic better