Thanks!! Glad it was helpful!

Thanks and thank you for stopping by!

@@kimandtech Thank you! I actually bought a set last week. I'm running them in AP mode with wired backhaul through my existing network switch (TP-Link) and the performance is amazing! Your thorough review and warning were very helpful.

@@tonystephenson9961 Nice!! Thank you for sharing your experience!

Thank you for sharing your experience. I don’t recall having this problem, but it’s been a few months. 😆 However, I’ll keep that in mind for my next TP-Link Deco test. Greatly appreciate it!!!

It will re-boot automatically, just like an other if there is a power failure? Correct?

I have the Deco M4 and my power goes out a lot. It reboots / reconnects itself. I’ve never had to do anything to reconnect it.

@xxcutive - Hello. I don't know how many LAN ports your model has. If it has 3 LAN ports, the you can have a full wired connection in multiple ways. If there are only 2 LAN ports, then you'll need to daisy chain the connection to have a full wired connection. For example, Main Router connects to Satellite 1 via wired connection, and Satellite 1 is wirely connected to Satellite 2.

I think you can set it up as a wired Access Point if you don't want to use it as a router. I haven't tried it, but I'm including a link for you here on how to set it up. www.tp-link.com/us/support/faq/1842/

Unfortunately, I don't know which TP-Link products Costco will carry.

I didn’t experience this issue. I’d recommend to check your settings to confirm nothing was accidentally disable. You can try turning off all your WiFi routers and turning them back on. Worst case, reset all routers and modem, and set up the routers again.

Hello. From a quick search, here's a link to the TP-Link forum. Please check it out. Hope it will help. If not, try resetting it. Worse case, you might have a bad one. Link: community.tp-link.com/en/home/forum/topic/267192

@@kimandtech ....Thank you for getting back to me.

Hi! Yup, they are all identical and have 3 ports for LAN lines on the back of each Deco for this model, so you can definitely plug in your PlayStation or desktop. 🎮🖥️

Hi Barry. Oh, interesting. From where you see them listed as Unsecure Networks, are you able to set them as secure? Or if you power cycle all of the Deco devices, do they show up properly on the app then? Unfortunately, I don't have my Deco anymore, so I cannot test for you.

@@kimandtech I see them as unsecure when I list "Other Networks" (e.g. Deco_6953 with no padlock). I've tried to turn on and off but they just won't show on the app. Thanks for your reply.

I guess the last thing you can try is remove the Deco and set them up again. Or email their support. Good luck with your troubleshooting Barry.

@@kimandtech Thanks Kim. I just need to troubleshoot now. Will switch routers around, etc and see what happens. All the best to you and yours. I am Subscribed.

Thank you Barry!!!

I didn't play with the different placements when I had the XE5300, so I'm not 100% sure. However, here are a few of things you can look into: - Did you select the layout that is the closest to your home layout during the setup? - Is the 5th Deco between #3 & #4 closer to 2nd? - Is the 5th Deco between #3 & #4 closer to a microwave or some sort of obstruction that could affect the performance, where it's better to connect to #2? Here's an article I found on the TP-Link website if you want to read a bit more. www.tp-link.com/us/support/faq/1446/ You may need to try with different placements of your Deco devices to see if the network diagram changes. Good luck!

Great discount! I got mine from Costco.