Training to use DSN-VC288 Digit Voltmeter Ammeter?

No video

Training to use DSN-VC288 Digit Voltmeter Ammeter?

Рет қаралды 74,343

Күн бұрын

How do you use DC 0-100V 10A DSN-VC288 Voltmeter-Ammeter Blue + Red? for beginners step by step? along with a digital multimeter and using 2 12 and 24 volt adapters and using a fan to show ampere consumption
--------------------------
In this video, I measure voltage and amps separately. I use 12 and 24 V adapters to measure the voltage. I use a fan to measure the ampere. I use a multimeter for comparison.
I will show you the correct way to connect the wires.
--------------------------
my Tools:
DC 0-100V 10A Voltmeter Ammeter: bit.ly/3uCE178
DT9205 multimeter: bit.ly/3HomdEb
24V 2A Power Supply Adapter: bit.ly/3Pjfyx8
12V 5A Power Supply Adapter: bit.ly/3W7HuGt
fan 4*4mm 12V: bit.ly/3Yb456J
------------------------------
Voltage Amperage Power Energy Meter / Tester Voltmeter Ammeter Watt Meter
▬ Social Media ▬▬▬▬▬▬▬▬▬
❤️❤️ If you liked this video, please like this video and follow our channel.
☑️☑️Also support us by sharing the video
📢 Subscribe Channel: / @newtecpro
Twitter: / newtecpro
Instagram: / newtecpro
Email: newtecprof@gmail.com
Telegram: t.me/newtecpro

Пікірлер: 26

@gasSpring888vn Жыл бұрын

thank you so much

@newtecpro Жыл бұрын

thnx bro

@hugodavid2244 Жыл бұрын

I just bought two of those meters, I connected them the same as you, but, although it shows the use of voltage and the circuit works without problems, the meter does not measure the current, it is simply at 0, both meters behave the same.

@newtecpro Жыл бұрын

Most likely, you have not connected the wires correctly. Please check the wiring method carefully Also, the electrical device must be turned on and consume electricity.

@hugodavid2244 Жыл бұрын

@@newtecpro The problem was that they ripped me off, it doesn't even have the metal bar that is used as a resistor to measure current.

@georgioszotos5519 Жыл бұрын

@@hugodavid2244 Yours must be V2.0 Without a wire shunt. But on the other side of the A connector there must be an SMD shunt resistor R010. And is brighter as normal SMD resistors. So is my. It works but i haven't used for more than 2 Ampere.

@mongneverdied1 9 ай бұрын

Thanks

@newtecpro 9 ай бұрын

Welcome my frind

@Flatron888 Жыл бұрын

Quick question. What happens if i try to read 105volts with it.... i have a power supply that can deliver little more over 100 and i dont want to burn the module. Will it burn if i exceed the 100v? or it wont show anything more than that 100 stucked in there.

@newtecpro Жыл бұрын

Yes, most likely higher than 100 volts will cause damage. Never use more than 100 volts

@Panda-in9zm Жыл бұрын

thnks

@newtecpro Жыл бұрын

TNx u

@sehajpalsingh1223 Жыл бұрын

What is cost of this meter

@newtecpro Жыл бұрын

Its price in online stores is approximately US $3.73

@sahityabodra1412 15 күн бұрын

Accurate....?

@newtecpro 15 күн бұрын

Measure Accuracy: 1% (± 1 digit)

@dinamics2 11 ай бұрын

When i connect shunt ampre readind going to zero, why?

@newtecpro 11 ай бұрын

You may have connected incorrectly. The shunt must be installed in parallel

@dinamics2 11 ай бұрын

@@newtecpro yes its parallel connected.

@mohammadpour.61 Жыл бұрын

سلام خسته نباشید ممنون مهندس یک توضیح کامل میخواستم دررابطه باطریقه فعال کردن آمپر من یک رسیورمینی دارم که دوازده ولت دوآمپره که ازطریق ماژول افزاینده وپاوربانک میخوام به رسیور برق برسونم اندازه گیری ولتاژوروکه بلدم ولی چطور آمپرو وصل کنم یاانتقال بدم به رسیور ومطمئن باشم که دوآمپر برق مصرف میکنه منظورم اینه دوسیم روبکجای رسیور وصل کنم ممنونم اگه یکم راهنمایی بکنید متشکرم موفق وپیروز باشید❤❤❤

@newtecpro Жыл бұрын

The amperage is nothing to worry about. In the technology of switching power sources, the electronic device consumes as many amps as needed. If your receiver uses 2 amps, it will only receive 2 amps.

@mohammadpour.61 Жыл бұрын

@@newtecpro thanks❤❤❤

@JavedKhan-qh3en Жыл бұрын

20 HP 3 phase motor ke liye chahie

@newtecpro Жыл бұрын

@ratkooporonty Жыл бұрын

The reality is that the old (analog) instruments could be used as long as no overcurrent was introduced by mistake, so they were good for many, many years. Today's (digital) instruments don't last more than a year or two, and they break down if they happen to be near the high voltage of an old TV. Some of them are already defective, so today's technology is not user friendly, but hazardous waste friendly.

@__-hh3gt Жыл бұрын

You are correct. Thanks