Transfer Case Output Shaft Seal Replacement

Рет қаралды 153,624

5 жыл бұрын

Did our video help you? If so, consider buying us a beer: bit.ly/3feE6tJ
In this video, we show you how to replace the transfer case output shaft seal on your 3rd Gen 4runner or 1st Gen Tacoma. We also show you how to replace the seal inside the companion flange.
*PARTS*
*Rear Output Shaft Seal #90311-41007
amzn.to/2PKJvJk
*Companion Flange Seal #90312-23001
amzn.to/392oPEf
*Companion Flange Nut #90179-22016
www.ebay.com/itm/Genuine-Toyo...
*If you happened to need to replace the Front Output Shaft Seal on your transfer case, the part number is #90311-41012 amzn.to/2sWOldi
*HELPFUL TOOLS*
If you're looking for other tools not used in this video, check out Timmy's Master Tool List.
www.amazon.com/shop/timmythet...
*Gear Wrench X-Long Ratcheting Box End Wrench Set
amzn.to/2CLX0BE
*Camshaft and Crankshaft Tool Kit
amzn.to/2YxJvPj
*Universal Press/Pull Sleeve Kit
ebay.us/4V5LlN
*OTC Long Prybar Set - (this set is good when you need lots of leverage)
amzn.to/2O7pWKZ
*Mayhew 5 Piece Prybar Set - (this set is good for jobs when light to moderate force is needed)
amzn.to/2Ob8THw
*Plastic Mallet
amzn.to/2CCOqVP
*Brass Drift Set
amzn.to/2WtPXFf
*1/2" Drive Flex Head Gear Wrench Ratchet
amzn.to/2Wnbq2r
*30mm 1/2" Drive Socket
amzn.to/2WySzkX
*CDI 3/8" Drive Torque Wrench
amzn.to/2U2vUA4
*Crowfoot Wrench Set
amzn.to/2WBR9X8
*CDI 1/2" Drive Torque Wrench
amzn.to/2UPhyjK
*Red Devil Grease
amzn.to/2WlnxwR
*Mini Grease Gun
amzn.to/2OnBBTK
2" x 3" Galvanized Nipple
amzn.to/2I8KMXm
2" Galvanized Cap
amzn.to/2HVDtme
**As Ebay Partner Network members, we earn commissions from qualifying purchases.
**As Amazon Associates we earn from qualifying purchases.

Пікірлер: 507

@TimmyTheToolman 4 жыл бұрын

*PLEASE READ THE VIDEO DESCRIPTION FOR HELPFUL INFORMATION*

@matthewwall5958 4 жыл бұрын

Great video, it helped me a lot thank you.

@TimmyTheToolman 4 жыл бұрын

@@matthewwall5958 Thanks Matt and you're very welcome. Great to hear our video helped you out. Happy Wrenching!

@two_stroke_or_broke9297 4 жыл бұрын

Is the companion flange seal a oil seal also???

@TimmyTheToolman 4 жыл бұрын

@@two_stroke_or_broke9297 Good question. Hard to say but I imagine some gear oil could travel along the splines and get past the end of the shaft so maybe it doubles as a gear oil seal and a dust seal.

@two_stroke_or_broke9297 4 жыл бұрын

Timmy The Toolman awesome thanks for your reply

@hectorrivera9894 3 ай бұрын

You should be an instructor. This is about the best "How to" video I've ever seen. Love the details and alternate methods/tools to use. If you can't do the job after watching this video. You have no business working on vehicles.

@TimmyTheToolman 3 ай бұрын

Hey Hector, I appreciate the nice compliment. You will find that all of our videos are very detailed to give the viewer the best chance at success. Thanks for taking the time to comment. Happy Wrenching!

@aaronleavitt8235 5 жыл бұрын

One trick I read on a Toyota forum and have since used is to take a small drill bit and drill out the dent of the staked nut. Can't do this in every location but it's what I used when I replaced my transfercase seals. Thank you Timmy for another excellent video!

@TimmyTheToolman 5 жыл бұрын

Hey Aaron, drilling out the dent probably wasn't something I would have thought of but I can definitely see that it would work. I was lucky I had the right size screwdrivers that I could wedge between the shaft and the indented section of the nut. Somebody commented you could also just take a small chisel and grind it down to the size you need. Glad you like the video. Happy Wrenching!

@retiredstripes5632 2 жыл бұрын

Outstanding! Thoughtfully made tutorial. Finding multiple solutions if you don't have professional tools is much appreciated. This is the best how-to I've seen yet. Many thanks, amigo.

@TimmyTheToolman 2 жыл бұрын

Thank you for the very nice compliment. We appreciate it very much. You're very welcome and Happy Wrenching!

@bullseyetacticalfirearmstr8732 2 жыл бұрын

Thank you for the thorough description. I used your video to replace the front drive shaft seal. One part didn't work as shown - bending out the nut from the shaft. I pounded and pounded on a variety of screwdrivers with a five pound hammer and it wouldn't budge. I could get under the nut metal, but couldn't drive the wedge blade of the screwdriver in. I read how someone used a dremel to weaken the area, so I carefully tried that with a 1" cutoff wheel. Worked like a charm. Just be very careful that you don't cut into the shaft metal. It weakened the nut metal enough that I was able to pop it out of the shaft notch. Replaced everything, couldn't get a torque wrench on the flange bolts so I used some Loctite blue and "Gutentite" torque specs. I had to use a six-sided combination wrench with a pipe on it to loosen them, so I "torqued" them back to the same angle location of the wrench/pipe. Just drove it to town on Interstate 5 and back, no leaks! Yay! Thanks, Timmy.

@TimmyTheToolman 2 жыл бұрын

Nice! Take a look at this tool, it may help next time: amzn.to/3Cdcqv2

@thatwideangle9781 Жыл бұрын

Love the excellent detail in your videos! Thanks for helping all of us amateur mechanics!

@TimmyTheToolman Жыл бұрын

Thanks for the kind words. We appreciate it! You're very welcome. We all started as total amateurs, but the cool thing is auto mechanics can be learned with relative ease. If you put in the time to learn and you invest in tools, you can be just as successful as the professionals. Quite often, the only difference between the professionals and the DIYers is the fact the professionals spent a lot of money to attend a trade school in which they passed tests to get certifications. You don't need certifications to be a good mechanic. Happy Wrenching!

@hectorrequeno6995 6 ай бұрын

i want to thank you after running around the parts stores getting different size seals your part#s helped alot more than you will ever know 😂😂 2004 tundra double cab 4x4

@TimmyTheToolman 6 ай бұрын

You're very welcome Hector. I'm happy to know our video assisted you. Happy Wrenching Bro!

@smiddysmidton8313 3 жыл бұрын

Thank you brother Tim, still the best tutorials for these trucks on youtube period! cheers from Australia.

@TimmyTheToolman 3 жыл бұрын

Thanks My Australian Brother. We appreciate the nice compliment.

@TheToyotahilux 3 жыл бұрын

Awesome and helpful video. I just did the front companion flange on my 1990 rn130 4Runner. It’s the same process as the rear seal. Time consuming job but easy and manage d to do it without removing the cross member. Thanks for the advice.

@TimmyTheToolman 3 жыл бұрын

Thanks Sam. Good job getting the job done. You're very welcome and Happy Wrenching!

@williambb9913 Жыл бұрын

I was truly convinced I was going to be forced to open up the entire transfer case... of course Toyota would make this easier and cheaper from replacing on the outside. Thank you for you video. Saved me days and hundreds.

@TimmyTheToolman Жыл бұрын

You're very welcome William. It's good to know our video helped you out. Thanks for the comment.

@8953147 5 жыл бұрын

Packed full of tools and tips, thanks brother Tim!! German torque good!

@TimmyTheToolman 5 жыл бұрын

Glad you like it Brother Jake.

@transformer889 4 жыл бұрын

The best tutorial video I have ever seen, thank you

@TimmyTheToolman 4 жыл бұрын

That's a hell of a compliment. Sean and I appreciate it very much. You're welcome and Happy Wrenching!

@solluna2155 5 жыл бұрын

My man Timmy always helping us out . .. 💪🤙

@TimmyTheToolman 5 жыл бұрын

It's our pleasure.

@pablolopez-sr5cb 10 ай бұрын

👍🏻👍🏻✌🏻

@damontracyvis1017 4 жыл бұрын

I going to be replace a front pinion seal on a 09 Toyota Sinnai tomorrow, this information was very helpful.

@TimmyTheToolman 4 жыл бұрын

Good luck with the job Damon. Hope it goes smooth for you.

@ZuluComander 5 жыл бұрын

It's funny, It was just last week I was under my rig for something else and I noticed a drip coming out of my seal. First thought was "shit I don't think Timmy has done a video on that one yet"

@TimmyTheToolman 5 жыл бұрын

Well Commander, I'm happy to hear our timing was perfect for you. Let me know how the job goes for you.

@jake27schannel 2 жыл бұрын

I know this was 2 years ago but same lmao

@TunaCat929 2 жыл бұрын

Love the in depth guide. Amazing video!!

@TimmyTheToolman 2 жыл бұрын

Great to hear you appreciate the detail this video offers the viewer. Thanks!

@Petrovich1988 3 жыл бұрын

Very well created tutorial that leaves no questions on this procedure 👍

@TimmyTheToolman 3 жыл бұрын

Thanks for the nice compliment. We do our best to be as comprehensive as possible so people can succeed with the job.

@VROOOOOOOOOOOOOOOM Жыл бұрын

This was ridiculously good and helpful. I have to replace this seal on my 90 pickup. This should help a ton.

@TimmyTheToolman Жыл бұрын

Thanks for the compliment. We appreciate it! Good luck with the seal replacement on your pickup.

@RippSnortin Жыл бұрын

Have you done it yet? I need to do this on my 93 4 runner. But l don't think it has the smaller seal, just to bigger one. Am l right?

@lovelovelybe3850 4 жыл бұрын

Great video. Love the details! Thank you.

@TimmyTheToolman 4 жыл бұрын

Thanks and you're very welcome. We're glad you like the detail we offer in this video. You'll find all of our videos offer lots of detail because we want people to be successful using our tutorials.

@AntonioClaudioMichael 5 жыл бұрын

Love that will work for 4runner repairs

@hansdavis9081 2 жыл бұрын

Just did my timing belt kit replacement and had a bad oil leak prior to the fix. When i got down to my front main seal, i was able to remove it with my index finger and thumb! Thanks for the help on this Tim!

@TimmyTheToolman 2 жыл бұрын

Good to hear our video helped you out Hans. I think you commented on the wrong video though. You're talking about a timing belt job and you commented on our Transfer Case Output Shaft Seal Replacement video. Anyways, we appreciate you taking the time to comment. Happy Wrenching!

@hansdavis9081 2 жыл бұрын

@@TimmyTheToolman my apologies! You caught me, I've been binging your channel!

@TimmyTheToolman 2 жыл бұрын

@@hansdavis9081 No worries. Thanks for being a fan of our channel.

@chrisnkimberlymengel2602 5 жыл бұрын

Timmy, love your vids! I recently became the proud owner of a 2002 Tacoma v6 5-speed TRD. I'm thrilled to have found your channel! When I bought the truck it had 188k on the clock. The timing belt is not original but no record as to when it was changed. Your timing belt vid really inspired me along with all these others! THANK YOU! Maybe you could do a video about what tools you use most often? As I'm getting into this I'm learning what I'm going to need - e.g. metric set of impact sockets. I'd be curious what your thoughts are on a starter set of tools might be for a beginning DIY wrencher. Thanks in advance and keep up the GREAT WORK!!!

@TimmyTheToolman 5 жыл бұрын

Hey Chris and Kimberly, great to hear you like our channel. Others have shown interest in a tool box walk through of what I own and we will make this video at some point in the future. Happy Wrenching and have lots of fun with your new toy.

@happycat0411 3 жыл бұрын

Great video! Replacing the rear seal on the transfer case isn't too difficult a job. I would think that this would be a two person job for ease and the extra hand would help immensely. Having access to the proper tools before a person tackles the job helps a lot as well. Well done and super easy to follow video! I was also surprised that no fluid came out after the yolk was taken off. That's a real blessing as well. Sometimes knowing what's going to happen in advance prepares a DIY mechanic for what the entire job entails, Letting the person know whether or not the job is overly difficult or the job is really doable for the weekend home mechanic is always a great way to learn and to save money!

@TimmyTheToolman 3 жыл бұрын

Thanks Bob. Glad you found our video helpful.

@williamtsol636 5 жыл бұрын

Best Tacoma channel for sure !

@TimmyTheToolman 5 жыл бұрын

Thanks William.

@iamoutofideas13 3 жыл бұрын

These guys are a national treasure.

@TimmyTheToolman 3 жыл бұрын

Ok, when's the Secret Service Detail show up to protect us? 😁 But seriously now, thanks for the nice comment. We appreciate it!

@cory8791 Жыл бұрын

I really wish someone would do a input seal for the transfer case! Great vid!

@TimmyTheToolman Жыл бұрын

One day it will happen. Glad you like the video,

@jasonarstell8039 4 жыл бұрын

Very good video. One of the best I’ve ever seen

@TimmyTheToolman 4 жыл бұрын

Thanks Jason. We appreciate the nice compliment.

@GXKid06 5 жыл бұрын

Great video as always!

@TimmyTheToolman 5 жыл бұрын

Thanks Jax.

@rthomas2157 2 жыл бұрын

Wanted to add an additional option that worked out for me along with the press sleeve and nipple option that Tim gives in the video. I found a piece of muffler/exhaust pipe at my local AutoZone that was the perfect diameter to fit around the new seal it captured the seal and held it in place just like the press sleeve or nipple did in the video. I then just used a piece of 2 x 4 held in place on the one end to drive the seal in evenly. This was inexpensive and worked out great for me although I did noticed that the edges are fairly sharp so I would highly recommend putting some tape or other material around one of the ends to add some padding or cushion to it for when you Are placing it against the seal it won’t bind or cut into the seal causing damage.

@TimmyTheToolman 2 жыл бұрын

Thanks for sharing your technique to drive the seal in.

@davidezwaaf1195 2 жыл бұрын

Thanks Timmy you guys are the best!

@TimmyTheToolman 2 жыл бұрын

You're welcome!

@Thr33.Sid3z 4 жыл бұрын

Sockets also work pretty well to tap in seals. Thanx for the vid!

@TimmyTheToolman 4 жыл бұрын

I could see sockets working well to drive in seals. For this application, it would have to be one huge socket. Maybe a diesel truck mechanic might have something that big in his tool box. You're welcome and Happy Wrenching!

@Thr33.Sid3z 4 жыл бұрын

@@TimmyTheToolman Yeah that's what I was thinking. I have a few 2in sockets... Idk how big the seal is on my Evo. I'm still trying to figure out where the leak is coming from, but I'm 90% sure it's the output seal cuz I'm getting fluid all over my Downpipe and I think that's the only location high enough to do that...

@TimmyTheToolman 4 жыл бұрын

@@Thr33.Sid3z I"m sure you'll figure it out. Good luck with the repair.

@johnremus 5 жыл бұрын

Woo hoo! Thanks again for the help with everything!

@TimmyTheToolman 5 жыл бұрын

Our pleasure John. Thanks for trusting us with you rig.

@tadheath5856 4 жыл бұрын

DAMN !!!! YOU ARE THOROUGH AS HELL!!!!!! THAT IS AWESOME!!!!!!!!!!! LOVE YOUR WORK!!! Wish you lived in ny....now I got a 2015 Tacoma....it looks just like that transfer case. Now i have a 2" leveling kit...it has two spots on the block lift in the rear...a stupid scammer put it on the spring pin all the way forward so it was setting in th back hole putting all the off the spring pad and all the weight on the front if the spring. So my spring would go up and over the axle. He pushed the carrier bearing all the way forward. I know that wouldnt be good on the seals and the u joint...I just replaced everything center u joint and carrier bearing..and thought I had the rear end out back where it was suppose to be. Driver side was 133" wheel base and passenger side was 132" wheel base. Remind you a Toyota dealer did the repairs. They never put the axle back where it was suppose to be on the passenger side. Now my u joint is bad and my transfer case is leaking. I know that ruined those seals with that rear end off one inch on one side. What is your opinion? Thank you!!!

@TimmyTheToolman 4 жыл бұрын

Thanks for the kind words. Glad you like our channel. Sounds like you have experienced what a lot of people have experienced. Even the supposed Toyota Experts regularly screw things up. This is the reason why I now do most of my own work. I bet because the rear end being out of alignment put strain on the u-joint and the transfer case seal and that's why they both failed. If I were you, I'd try to get the Toyota dealership to compensate you for the screw up.

@MrRamathon 2 жыл бұрын

Great video, have me the confidence to get it done. I will say, spend the time to find something to press the seal in. The video goes into it but I thought I was smarter.....I was wrong.

@TimmyTheToolman 2 жыл бұрын

Great to hear our video gave you the confidence to tackle this job. The right tools makes life easier for sure. Happy Wrenching!

@lukeneave 5 жыл бұрын

Always learning new tricks removing zerk fitting, ever experienced blocked zerks or unis?

@TimmyTheToolman 5 жыл бұрын

I've never had a blocked zerk fitting but I imagine it does happen.

@djsonicc Жыл бұрын

Very good, and straight to the point

@TimmyTheToolman Жыл бұрын

Thanks!

@user-bm4qf2ox1f 7 ай бұрын

Delisious video. Had what i was looking for thanks.

@TimmyTheToolman 7 ай бұрын

We got Tasty-mods. -Sean

@thingsthatmake 4 жыл бұрын

I noticed some videos where they also replace the needle bearing on Tacomas with a bushing. Is this a common failure on the 4Runner as well? Getting ready to do the CV's on mine soon. Thanks so much for the awesome detailed informative educational videos! : ) Greatly appreciated my friend, priceless info.

@TimmyTheToolman 4 жыл бұрын

The needle bearing failure on the driver side differential is fairly common with lifted 4runners too. 3rd Gen 4runners and 1st Gen Tacomas have the same exact drivetrain. When the rig gets lifted, the extra angle for the CV axles can cause a strain on that needle bearing and people will feel a vibration and roaring noise from the front end when the needle bearing starts to wear out. We made a video on this repair. Check it out: kzfaq.info/get/bejne/qb55maty19radmw.html

@eckhardkoehler3013 3 жыл бұрын

You are a stud! Thanks for the thorough video.

@TimmyTheToolman 3 жыл бұрын

Thanks and you're very welcome. Good luck with the job.

@eckhardkoehler3013 3 жыл бұрын

@@TimmyTheToolman thank you. You've made it look straight forward. Going to check with Toyota that the 2004 is similar, and then hope that's the only cause of my leak as it looks to be coming from the rear and possibly forward. Guess I can start and then see if everything resolves

@TimmyTheToolman 3 жыл бұрын

@@eckhardkoehler3013 I would suggest cleaning up everything very well with degreaser and rags and then watch it carefully to figure out the true origin of the leak before you replace anything.

@strongbackmfg15 7 ай бұрын

Thanks buddy! Great video

@TimmyTheToolman 7 ай бұрын

You're welcome.

@MuskDeer-Pk 4 ай бұрын

nice stuff. learnt a lot. thanks a lot for sharing your valuable experience. God bless you.

@TimmyTheToolman 4 ай бұрын

I'm happy to know you learned a lot from our video. You're very welcome, and God bless you too.

@jackempson3044 Жыл бұрын

Great clear video.

@TimmyTheToolman Жыл бұрын

Thanks for the compliment, Jack.

@SBecktacular 3 жыл бұрын

Nice vid and very clear communication... 👌

@TimmyTheToolman 3 жыл бұрын

Thanks. We're glad you like it.

@justing1810 8 ай бұрын

Great video I'm going to have to do this job soon on my ranger

@TimmyTheToolman 8 ай бұрын

Thanks! Good luck with the job

@AntonioClaudioMichael 5 жыл бұрын

Great walk through

@TimmyTheToolman 5 жыл бұрын

Glad you like it Antonio.

@AntonioClaudioMichael Жыл бұрын

I can't find the dust Shields that protect the seals is that apart of the companion flange and the Transfercase housing ? Not seeing it in the Shop manual in the transfer case section?

@albertdemeo7405 3 жыл бұрын

As always great video. Have you considered doing a video on replacing the other transfer case seals? My case is leaking somewhere near the top, virtually the entire case is caked with leaked oil and grime.

@TimmyTheToolman 3 жыл бұрын

Possibly but because removal and installation of the seals on these output and Input shafts are the same it will just as good as watching one of our videos on the matter, then just use the right part number for the seal.

@ecordy 4 жыл бұрын

Excellent video

@TimmyTheToolman 4 жыл бұрын

Thanks. Glad you like it.

@luisolitoquit4481 5 жыл бұрын

Hi Timmy, very good video. I need to know if you have a video on how to replace an oil pan gasket. I want to do it on my 97 4runner because I am having a small leak . Also after watching the 30,000 mile video, I did change the front differential gear oil and transfer case gear oil today just by watching your video. Thanks again.

@TimmyTheToolman 5 жыл бұрын

We haven't done an oil pan gasket replacement video yet. But, we have a video for pulling the front differential and that's most of the work. kzfaq.info/get/bejne/rcWXg8x1286dpmg.html Be sure to read the comment I pinned because we learned of a much easier way to get the front differential out. Once the front differential is out of the way, you can remove the oil pan with relative ease. Take a look at our Transmission Filter Replacement video. The tool and technique we use to separate the trans pan from the transmission would be the same technique to separate the oil pan from the bottom of the engine. kzfaq.info/get/bejne/qtt3lN1_zduppIE.html

@rahalati 2 жыл бұрын

Excellent job and nicely explained, thanks for sharing. I wish a similar video is done to show how to replace front oil seal of a 1998 land cruiser transfer case

@TimmyTheToolman 2 жыл бұрын

Thanks for the compliment and you're very welcome. Maybe one day we'll do the same on a 100 Series Land Cruiser.

@rahalati 2 жыл бұрын

@@TimmyTheToolman Thanks for your reply. Do you think overtightening or not tightening enough the 30 mm nut that attaches the companying flange to the output shaft of the transfer case, do you think it will misalign the seal to cause it to leak even if you are sure it was inserted properly? I replaced my 1998 Land cruiser rear transfer case seal and I am sure I did it correctly, but I am getting leak again.

@TimmyTheToolman 2 жыл бұрын

@@rahalati Under tightening or over tightening the nut wouldn't cause the seal to ride in a different spot. Sometimes the seal can wear a groove in the actual metal of the companion flange, and even with a new seal, it will leak. Did you carefully examine the surface the seal is riding on to see if there was a detectable grove in the companion flange metal? If there is a groove, you have a couple choices. Replace the seal and don't drive it fully so the seal will ride on the companion flange in a new and non-grooved surface. The other option is to get a replacement companion flange.

@rahalati 2 жыл бұрын

@@TimmyTheToolman thank you so much. At least now I exclude the issue of the nut tightening. In fact the rear seal was not leaking initially, but decide to replace it along with other seals in the transfer case since I already opened the transfer case to replace the front seal which was leaking. Fortunately now that the rear seal is our issue which does not require the transfer case to be opened again. I will have to go back and check it and follow your advice. Thanks

@TimmyTheToolman 2 жыл бұрын

@@rahalati Hope you figure it out. Let me know how it works out.

@oliviaoutwest 4 жыл бұрын

Just a heads up the rear output shaft seal part number is now 90311-41020. I just ordered from Toyota and this replaces 90311-41007. Looking forward to using this video as a resource to fix my leaking transfer case seal. Whenever I have an issue with my 4Runner the first place I look for help is Timmy the Toolman's videos!

@TimmyTheToolman 4 жыл бұрын

Hi Olivia, thanks for sharing the information regarding the part number change for the seal. Good to hear we are a resource you like to use for working on your rig. Happy Wrenching!

@BnaBrat 4 жыл бұрын

Thank you so much! I was stuck on this today! You made my day!!

@TimmyTheToolman 4 жыл бұрын

You're very welcome! Glad your video helped you out.

@BnaBrat 4 жыл бұрын

Can I drive it in 4WD just to make sure the vibration is in the rear driveshaft that is out of the vehicle now?

@TimmyTheToolman 4 жыл бұрын

@@BnaBrat Well, on pavement you can use 4WD but you have to be careful. If you're just going in a straight line, no problem. If you do some turns, there will be a binding that will happen with your axles and your front differential. So, if you can get it on a straight road, drive it to see if the vibration is gone. Stop. Take it out of 4wd and physically push the rig to get it turned around, maybe with the help of a buddy, and then put it back in 4wd to get home, this could work. If you take turns on pavement in 4wd, you can end up causing damage so you need to be very careful.

@BnaBrat 4 жыл бұрын

So my driveshaft guy told me today the driveshaft that was with my 4runner that I purchased in Jan with 325K on it was to short the splines were showing a little at the rear flange. That is what is causing the vibration. Trying to figure out what this old driveshaft goes to other than my 4runner?

@TimmyTheToolman 4 жыл бұрын

@@BnaBrat Who knows. The previous owner pulled it off another Toyota most likely, maybe something like a RAV 4. At least you figured out your problem. Maybe you can find a used one at a wrecking yard like a PickNPull.

@AntonioClaudioMichael 5 жыл бұрын

Great video timmy

@TimmyTheToolman 5 жыл бұрын

Thanks Brother!

@dangda-ww7de 5 жыл бұрын

You know because of your videos i when out and bought 2 tundras both are v6, one is 2001 the other is 2002, one with 175k and the other is 225k miles, one is automatic other is stick. So far i did replace timing belt on both, im just waiting incase my engine goes out i might need a swap video from you soon. lol im not planing to swap it yet but just in case.

@TimmyTheToolman 5 жыл бұрын

Great to hear our channel inspired some vehicle purchases for you. We might do an engine swap at some point. Have fun with your new used rigs.

@MykMallett 4 жыл бұрын

Brilliant video. Do you definitely need all 4 wheels off the ground? I only have 2 jack stands at the moment

@TimmyTheToolman 4 жыл бұрын

No, you don't. But, it would give you a little more room to work though. We're glad you like the video and good luck with the job.

@mikeymcnair4286 2 жыл бұрын

hi timmy, i got a 92 v6 auto 4x4. same process? which way does the seal go? lip out towards the comp. flange or inside the t case?

@TimmyTheToolman 2 жыл бұрын

Hey Mikey, we've never done the job on a 92 4runner but I imagine the process is the same. I don't know the orientation of the seal. Just carefully analyze the seal orientation before you remove so you know how to install the new one.

@colvinjonas1486 5 жыл бұрын

Thanks for the info Bro

@TimmyTheToolman 5 жыл бұрын

You're welcome Brah.

@2byoda 4 жыл бұрын

Hey think you can help me out? Been having vibration and thought it was ujoints but I checked and has play where driveline meets transfer case. Any idea?

@TimmyTheToolman 4 жыл бұрын

If there's play, that means the bearing in the transfer case is on it's way out.

@skiparock 4 жыл бұрын

great video, thanks

@TimmyTheToolman 4 жыл бұрын

Thanks for thanking us! We are thankful.

@HandyAndy999 11 ай бұрын

I have a 2006 Tacoma trying to change the Front transmission seal. I unbolt the 2 bolts holding up the shaft that's almost in the middle distance. Question - do I need to unbolt the rear shaft bolts at the rear end OR can I pull the front shaft out where seal is sitting without removing the rear shaft bolts. Appreciate your advice thank you. Andrew

@TimmyTheToolman 11 ай бұрын

The rear shaft is totally separate from the front. If you want to replace the front output shaft seal, you only have to disconnect the front driveshaft from the transfer case.

@jlc7300 3 жыл бұрын

Good detailed video, would this be about the same procedure for a 99 Rav4 AWD?

@TimmyTheToolman 3 жыл бұрын

Thanks. Don't know if it would be similar to the RAV4. We've never worked on one.

@lenlenman 4 жыл бұрын

Hey Timmy, I need to do the seal on my transfer case, but the one for the front companion flange connected to the front driveshaft. I know you don't have to drain the case for the rear flange, but do I have to drain all the gear oil for doing the front seals since it's much lower that the rear one?

@TimmyTheToolman 4 жыл бұрын

Hey Ian, yeah, I would drain it if you're doing the front seal.

@santossanchez872 2 жыл бұрын

is this procedure the same for 1992 toyota pickup i'm like one of your viewers thought it was the rear but it ends been the transfer case output shaft seal?

@TimmyTheToolman 2 жыл бұрын

I'm guessing it would be similar but I can't say for sure. I've never done this job on a 92 pickup. For sure you should make sure you get the correct seals. I also don't know if the part numbers are the same.

@jessicaoswell7361 2 жыл бұрын

If you have 2wd Prerunner would the same size pipe work for seal on the output shaft spline area?

@TimmyTheToolman 2 жыл бұрын

Not sure but I'm guessing it will.

@Lucas-ix8bg 2 жыл бұрын

nice video..i changed the seal following the instructions. now i have a suspected bearing sound coming from the front transfer drive. can the sprocket drive bearing be changed without taking down the whole transmission?

@TimmyTheToolman 2 жыл бұрын

I'm not 100% sure but I believe you would have to crack open the transfer case to get at that bearing and then for sure you would need a press to get the bearing off the shaft. So, the transfer case needs to come out. The transmission wouldn't need to come out though.

@mymercury1961 2 жыл бұрын

Thank you very much for the video on hints & how to do, Do you have any idea if the front output flange to the front diff is done the same ? Thanks again and look forward to a reply.

@TimmyTheToolman 2 жыл бұрын

The steps would be the same but the seal isn't. We list that front seal in the video description.

@grilledchickenwrap 6 ай бұрын

They look similar to other cars like my 2014 Nissan pathfinder I seem to be developing a leak in the rear transfer case output shaft seal.. did you totally remove the drive shaft or just left it hanging ? I’m thinking about doing my Nissan but was wondering for best way since I’m am doing it in my driveway lol with car jacked up. Thanks!

@TimmyTheToolman 6 ай бұрын

I can't remember 100%. I think we removed the driveshaft entirely. Just pay attention to how far the seal is driven in and copy that when you install the new seal.

@rouge0449 2 жыл бұрын

Hi Tim. I got a 1999 Rav4 AWD and oil is dripping from what is looks like a weep hole. Can I plug the hole to stop the leak?

@TimmyTheToolman 2 жыл бұрын

There isn't a weep hole as far as I know but there are breathers to relieve pressure. I don't exactly know what you're referring to so I couldn't give you any advice on it.

@redgreen610 2 жыл бұрын

I wanted to ask about the crows foot wrench. I bought a set so I could torque to specs, but I still couldn't get enough clearance to seat the wrench properly with torque wrench and an extension didn't help. Maybe the double cardan joint is bigger on a 96 or the wrenches were shorter than yours. They looked the same. I ended up using "good and tight" on a 14 mm with extension. Because you are offset from the axis of rotation of the nut, would you risk over-torquing those nuts with a crow's foot? If at all, maybe it's insignificant.

@TimmyTheToolman 2 жыл бұрын

Good and Tight is good enough. I wouldn't worry about exact torque specs for the driveshaft bolts and nuts you can't get a straight shot at with the torque wrench. I've tightened many driveshafts with the good and tight method, and the nuts don't get loose and fall off.

@efil4kizum 8 ай бұрын

Hello Timmah! ... well i think i have spotted a weep of either MT transmission or transfer oil on the Gen1 Taco 5VZ... it looks to be somewhere between where the transfer case and R150F transmission mate up... gravity has pooled up a dropping on one of the lowest bolts... I wiped it off and checked a few days later and it was whett again... do you have any videos of what is involved with resealing where those two items attach?, i am taking a gander at the parts diagram and searching for the literature in the FSM pdf i have for more instruction and exploration

@TimmyTheToolman 8 ай бұрын

It's either the output shaft seal of the manual transmission or the input shaft seal of the transfer case. You'll need to remove the transfer case to investigate. The closest I have to a video for this is our Automatic Transmission Swap series, Part 1, where we show how to remove the transfer case.

@efil4kizum 8 ай бұрын

@@TimmyTheToolman thank you!

@davidezwaaf1195 2 жыл бұрын

Timmy! Hey guys live the channel and thanks for what you’re doing. So I have this same leak from the front side I assume that’s the input shaft seal I was just curious if you had a video for that procedure or if it’s the same as the rear seal and same parts? Thanks again guy’s

@TimmyTheToolman 2 жыл бұрын

The procedure is the same but the part number for the front seal is different. We list the part number of the front seal in the Parts List in the Video Description. Open the video description up by clicking on "Show More".

@devongrein1341 5 жыл бұрын

Hey awesome video. Does anyone know if this repair is similar to the 5th gen repair?

@TimmyTheToolman 5 жыл бұрын

Timmy and Sean don't know how similar it is but maybe somebody else does.

@blacktalonarmory5 9 ай бұрын

I recently pulled the driveshaft on my 2020 4 runner and noticed no side to side play in the TC flange however notice 1/16 in and out play. When I pulled the flange I noticed there was not a shim behind it. I'm not the original owner and my question is do you know whether or not the shims are there for the purposeof preloading the bearings? Is the in and out play acceptable ?

@TimmyTheToolman 9 ай бұрын

I don't believe the companion flange actually puts a preload on the bearing behind it. It's not like setting the preload for a pinion bearing on a differential. I don't remember the Toyota FSM discussing anything about this or any talk about shims. That play you are noticing might just be a little play in the bearing shaft and it could be normal, but I don't know for sure.

@santoslaguna58 Жыл бұрын

Does this oil seal part number also work for the front side of the transfer case?

@TimmyTheToolman Жыл бұрын

It's a different part number. We list it in the video description.

@jacksonwholeexperience409 4 жыл бұрын

Hey Timmer! Does this apply to my 2009 Tacoma 6-speed manual TRD Off-Road? Thanks.

@TimmyTheToolman 4 жыл бұрын

I'm not sure but I imagine the techniques we employ in this video would be the similar for your 2009 Tacoma transfer case. The seal part number and the torque spec for the companion flange nut my be different though.

@jeremyhes5998 3 жыл бұрын

Hey Timmy! Would you happen to have a source for a Reman t-case? I have looked all over and unfortunately the only ones I can find are from Marlin, etc but they are meant for way more abuse then what I would throw at it.

@TimmyTheToolman 3 жыл бұрын

Hey Jeremy, no we don't know of where you can get a remanufactured transfer case. Maybe there's a local shop in your area with a good reputation that rebuilds them for a fair price.

@PyrateRumRunner 7 ай бұрын

Thanks for posting the front seal info as well. Is it basically the same process? Thanks in advance.

@TimmyTheToolman 7 ай бұрын

Yeah, it would be the same process. You're welcome.

@corbs3535 Жыл бұрын

hi timmy quick question is the input seal at all similar to this seal or will it require a little more know how and equipment

@TimmyTheToolman Жыл бұрын

Replacing the input shaft seal on the transfer case is totally different. To get to that seal, the transfer case would have to be removed from the vehicle. I've never replaced one but I'm guessing it's similar to replacing the input shaft seal on a manual transmission. You remove the plate that houses it, pry out the old seal, install and new one, and reseal the plate back to the case. I'm guessing you're seeing gear oil dripping down from the juncture of the transfer case and transmission? If the leak isn't really bad, you could just leave it alone. If you're losing a significant amount, then you'd want to do the labor necessary to change it. We have our transmission replacement series where we show how to remove the transfer case.

@rthomas2157 2 жыл бұрын

Hi Tim. Thanks again for making this video it is very helpful I know this is been up a while so I am hoping you see this. I recently just replaced the rear output shaft seal on my first GEN Tacoma using your video here so far so good. Since then I have noticed a small amount of gear oil weeping out between the area where the transfer case and transmission meet up. I did a quick search on Tacoma world and found some comments that I believe were made by you about that it does not have a gasket or RTV seal that it is a dry seal metal to metal. Is this correct? Also if I am seeing gear oil leaking out in that area that it could possibly be my TC input shaft seal leaking or the Transmission output seal. I’m I understanding this correct? It’s not a very bad leak and is definitely gear oil which would seem to me it would be the input shaft seal. Just wanted to reach out to see if you thought it was worth while replacing? The area where the seal is located in the front companion flange is bone dry just leaking 2-3 drops from between the TC and Transmission. Thank you.

@TimmyTheToolman 2 жыл бұрын

Yes, the seal between the transfer case and transmission is a dry seal. There's no fluid in that void between the two parts. If it's gear oil leaking out, and you have an automatic transmission, the source of the leak has to be the input shaft seal on the transfer case because the auto trans has ATF running in it. If you have a manual transmission, then the leak could be either coming from the output shaft of the transmission or the input shaft of the transfer case. If the leak isn't that bad and you're keeping an eye on the fluid level on a halfway regular basis, you're fine. If the leak gets worse, then you're going to have to check your fluid levels frequently or risk messing up one of those expensive components. Pulling the transfer case isn't that hard but it does take some time. Our Auto Trans Swap Part 1 video will show you how to do it if you decide to drop it. kzfaq.info/get/bejne/pcB0hs2d3dKWgWg.html

@leo3325 3 жыл бұрын

Nice video! Do you know if Nissan Pathfinder 2014 has a similar procedure to replace seal? I was told by dealer that transfer case is not serviceable and ask 5000 bucks for replacement of the whole transfer case! Thank you.

@TimmyTheToolman 3 жыл бұрын

Not sure, but just under the rig, remove the drive shaft and flange and see if you can identify a seal. Also clean it real good to make sure the transfer case is leaking from something like a seal. Could be a crack or leaking from somewhere else.

@paytendampeer811 8 ай бұрын

Awesome!! Based off the looks this will work the same for my 5th gen 4Runner right?

@TimmyTheToolman 8 ай бұрын

The general steps will, but you'll have to make sure you get the correct seals for your transmission and pay attention to how the original seal was installed. You'll want to drive it in to the same depth as it was before. Sometimes, with seal applications, you can drive it in too deep, which causes the seal to not be riding where it needs to be on the shaft of the companion flange.

@BigBluePile Жыл бұрын

Thanks again!

@TimmyTheToolman Жыл бұрын

You're very welcome!

@BigBluePile Жыл бұрын

@@TimmyTheToolman I'm getting ready to do the front output seals!

@TimmyTheToolman Жыл бұрын

@@BigBluePile Good luck!

@JoseSoto-jb4ty 3 ай бұрын

Hi i have question i replace it on my toyota sequoia 2001 but i was expecting the small washer but it wasn't there what's the purpose of the washer?

@TimmyTheToolman 3 ай бұрын

Can you provide a time stamp to the washer you're talking about? We shot this video quite a while ago and I don't know what you're referring to.

@jasonrentfrow2078 2 жыл бұрын

Where did you get that sleeve from sir I need that so bad been trying to find something to install that seal with

@TimmyTheToolman 2 жыл бұрын

That sleeve is part of a crank and camshaft seal removal/ installation kit. A link to the kit is in the video description. Just click on "Show More" and the video description will expand out.

@harveygomez4943 10 ай бұрын

Hi Timy ! I own a 2001 2001Toyota Hilux motor 3L and I am trying to replace the front transfercase oil seal, but before that is a dust caver seal, how can I remove it with out damege it?

@TimmyTheToolman 10 ай бұрын

I'm not familiar with it so I can't really advise you how to remove that dust cover. What area of the World are you in. Maybe there's a Toyota forum you can ask your question on and somebody will be able to help you.

@laytonaschauer3675 2 жыл бұрын

My 03 GX470 is leaking ATF from where the transfer case meets the transmission. Is this a job that can be done with basic tools?

@TimmyTheToolman 2 жыл бұрын

Define basic tools? Think about what we used in this video. A way to pull the seal and install the new one may be the only specialty tools you might not already have.

@marc-olivierbaillargeon9125 2 жыл бұрын

Thanks!

@TimmyTheToolman 2 жыл бұрын

You're welcome.

@stonejordan710 4 жыл бұрын

Great helpful video! Trying to replace my front transfer case seal this weekend. Is the transfer case output shaft seal or the nut different for the front vs. the back seals?

@TimmyTheToolman 4 жыл бұрын

Glad you like the video. The front seal is different from the rear seal. We provide the part number in the video description. I don't know if the nut is different on the front. I would venture to say it's the same but I'm not 100% sure. A visit to you local Toyota dealership parts department would probably get this question answered though. Just give them the part number for the rear nut and ask them if it's the same for the front companion flange.

@bigboatsrule4409 4 жыл бұрын

@@TimmyTheToolman Thanks for updating the Front part number. Also, removing the grease zirk to relieve pressure, is a sick trick!

@dannynguyen8963 2 жыл бұрын

I have a 2004 gx470 that has the same leak. Are the seals the same part number ?

@TimmyTheToolman 2 жыл бұрын

I don't know Danny. I haven't performed this job on a GX470 yet. The seals aren't too pricey. If I were you, I'd just visit your local Toyota Parts Department and have them look it up for you and buy them there. You're going to pay more compared to online, but at least you're going to get the right seals. Trying to look up small parts like this from an online sellers website can be problematic because the parts schematics available aren't always very complete.

@ivanduron211 2 жыл бұрын

Hello Timmy, thanks for the video, can you tell me please the parts numbers of both seals? i have the same problem on my car

@TimmyTheToolman 2 жыл бұрын

We list them in the video description.

@gatzbravo 3 жыл бұрын

great video...i was actually looking for something on the other side of the transfer case. I recently noticed a drip from the drain plug. I tried tighting it but it was already tight. Maybe theres a seal on the front side that needs replacing. Its a 92 4wd pickup. Do these have drain plug washers that could be the culpret...anything to avoid a bigger hassle?

@TimmyTheToolman 3 жыл бұрын

Yes, the drain plugs do have aluminum washers. You could buy them at your local dealership or from an on-line Toyota parts supplier.

@gatzbravo 3 жыл бұрын

I did along with the recessed hex plugs which are so much easier to tighten. Thanks!

@TimmyTheToolman 3 жыл бұрын

@@gatzbravo You're welcome.

@RobertFitch Жыл бұрын

Timmy, You provided a very informative and straight forward video on the Transfer Case Output Shaft Seal Replacement for the Toyota 1st Gen Tacoma. Do you know if this procedure would be the same for 2005 Lexus RX330 AWD? My rear oil seal on my transfer case is leaking (badly!). All the quotes I have received total 18 hours of labor. They claim the transfer case would have to be removed. In your video the transfer case remains in the car while you replace the seal. I would appreciate any advice on the matter. The quotes I have received are any where from $3500-$4000. This is way to much for a 70 year old man on a fixed income. Again, Thank you for the great videos.

@TimmyTheToolman Жыл бұрын

Hey Robert, I'm not familiar with the Lexus RX330 so I'm not sure if the job would be similar. I wonder why the transfer case would have to be removed to replace the output shaft seal. It doesn't make sense. Send me a picture of where the seal is so I can give you a more definite opinion on it. I did a quick search and found this: repairpal.com/estimator/lexus/rx330/transfer-case-output-shaft-oil-seal-replacement-cost Maybe the shops are misunderstanding what's leaking.

@forestbell3853 3 жыл бұрын

Ok so if you are going to replace the front output shaft seal would you need to get another companion flange smaller seal And companion flange nut for the front? Are they almost a identical set up? Also would the smaller seal and nut be the same part number as the rear? Thanks In advanced

@TimmyTheToolman 3 жыл бұрын

They are almost an identical setup but I’ve heard there’s different part numbers for the front companion flange seals so make sure you get the right ones.

@jake27schannel 2 жыл бұрын

Another useful video I found! both sides of my t case are leaking. So to do the front would I use all the same parts except instead use the front output shaft seal with all the other parts?

@TimmyTheToolman 2 жыл бұрын

Pretty much! You got it!

@jake27schannel 2 жыл бұрын

@@TimmyTheToolman Thank you! all your videos have helped me so much over the Years and expanding my skills. much appreciated

@CitizenSnips05 2 жыл бұрын

Any chance there's a part number for that companion flange washer @ 14:15? Mine was completely missing when I took off the companion flange. Not stuck to the back or anything.

@TimmyTheToolman 2 жыл бұрын

Sorry Steve, I don't know the part number. I suggest you just visit your local Toyota dealer parts department and order it from them. It can't cost that much. The shipping you'd pay from an online seller wouldn't make it worth it.

@CitizenSnips05 2 жыл бұрын

@@TimmyTheToolman Thank Timmy, I actually found the answer on Tacoma World. Looks like the part # is 36275-35010 for anyone else searching. Just costs a dollar from the dealer!

@TimmyTheToolman 2 жыл бұрын

@@CitizenSnips05 Thanks for sharing the part number Steve.

@BP_Cali 8 ай бұрын

Did you drain the TC fluid before this job? Or can you swap out the seal regardless?

@TimmyTheToolman 8 ай бұрын

You don't need to drain the gear oil to do this job.

@TheSponge945 10 ай бұрын

Go with the OEM seal or something from NAPA etc?

@TimmyTheToolman 10 ай бұрын

OEM

@martinravina6934 4 жыл бұрын

Hi Timmy thanks again for the amazing confidence boosting tutorials. I've ordered the parts in you descriptions but turns out it was the front seal leaking in mine (lower one), do both sides use the same seals? The flange one is the same indeed my concern is the transfer case one. Thanks again and greetings from New Zealand.

@TimmyTheToolman 4 жыл бұрын

I don't know for sure 100% but it would be my guess that it's the same seal. I tried doing a search online to confirm it's the same seal but the online Toyota parts sellers don't have the greatest parts schematics to consult. If this isn't your only vehicle, you could always just pop the seal out and then do a side by side comparison to make sure it matches up. That seal seems to be used for a lot of different year Toyota and Lexus model transfer cases all the way up to 2018. So, I'm pretty confident you're going to find it's the same seal front and rear.

@martinravina6934 4 жыл бұрын

@@TimmyTheToolman hey Timmy thanks for the reply, I've removed it and looks slightly smaller than the back one, not sure if shrinks a bit. Agreed I couldnt get a good schematic myself either. Found this that could be different: www.amayama.com/en/part/toyota/9031141012 Will go to the dealership today and ask will update for reference.

@martinravina6934 4 жыл бұрын

Checked with the dealer, all same procedure just different seal on the Transfer Case for Front is part number 9031141012. Thanks again Timmy you're the man!

@TimmyTheToolman 4 жыл бұрын

@@martinravina6934 Glad you got it figured out. Thanks for sharing the part number. I added it to the video description for anyone else looking for the same answer.

@shaknbake24 Жыл бұрын

Thank you for doing this! Would repairing the Front Output Transfer Case Seal be exactly the same process as replacing the Real Output Transfer Case Seal?

@TimmyTheToolman Жыл бұрын

You're very welcome. The process would be the same, but I think the seal might be different.

@shaknbake24 Жыл бұрын

@@TimmyTheToolman Thanks again! Love these videos. They are helping me keep my 2000 250K mile tacoma alive

@AntonioClaudioMichael Жыл бұрын

I can't find the Dust shields for the front companion flang or the rear Companion Flang or the dust Shields on the transfercase

@TimmyTheToolman Жыл бұрын

I'm pretty sure the dust shield is part of the companion flange but maybe you can buy it separately.

@AntonioClaudioMichael Жыл бұрын

@@TimmyTheToolman okay I can't find it and the companion flanges are 120 bucks a peice don't want to buy companion flanges for a 15 or 20 dollar dust shield appreciate the reply timmy and good to hear from ya been awhile