A helpful tip #wesselmotorworks #wrenchingwithkenny #keepwrenching #4l60e #4l80e #transmission #transmissionfluid #transmissionline #radiator #gmctrucks #gmcsierra #chevytrucks #chevy #chevysilverado #chevytahoe #chevysuburban
Пікірлер: 137
@LeeshaKay1990 Жыл бұрын
Omg I have been fighting with these transmission lines for an entire day. Thank you so much for your video!!
@toenails.2 жыл бұрын
Oh yeah I have done many of those clips on my work fleet. I just use a little pick and cuss and swear until I get it.
@HypeTv1002 жыл бұрын
what happenes if i dont put the plastic lock thing back will the line pop out ?
@toenails.2 жыл бұрын
As long as the metal clip is installed properly it is what holds the line on. The plastic disk just hides and protects it.
@chadwickdavis17492 жыл бұрын
Cussing is important! Nothing comes loose without a few choice words uttered!
@dirtpooroverland5396 Жыл бұрын
Or it eventually pops loose and dumps trans fluid all over the road… ask me how I know…
@youtubechangedmyname Жыл бұрын
@@dirtpooroverland5396 happened to me yesterday ....F these clips what a pain in the a##
@BD_Clark7 ай бұрын
FINALLY- a video on these clips that’s well lit and visible when you pop it off! Thank you for sharing this, very well done!
@chipmeister1116 ай бұрын
You've come a long way in a year from 700 subscribers to 80,000+, good for you and thanks for helping me understand these clips. Gonna change out the lines in my 02 Silverado 8.1.
@antoinesaunders25432 жыл бұрын
Learned that lesson today. Hopefully my trans is still working after I replace that plastic clip and a refill!
@timowensby36112 жыл бұрын
Have a 07 Grand Prix lower cooler line keeps popping out I believe the gentleman I hired to replace the lines and put it back in didn't reinstall clips
@dirtpooroverland5396 Жыл бұрын
So did it start working again once you got fluid back in it?
@baims836710 ай бұрын
ZIP TIES are a genius invention. They will work for your clip -collar lock ..
@pmp2559 Жыл бұрын
First time doing this and I’m learning a lot of words. Thanks for the assembly goo advice
@dirtpooroverland5396 Жыл бұрын
It’s interesting you mention it. I actually just had the exact scenario you discussed on my 2003 Suburban. Trans cooler line popped off driving down the highway and dumped the trans fluid. When I looked, all the plastic covers on every line were just hanging on the lines. Not on the fittings. Going through today and putting the line back on that came off and fixing the covers. Thanks for the video. I’ll give it a go.
@johnarohde9444 Жыл бұрын
I was wondering how to get the lines off my Malibu maxx and you definitely solved my issue with how to get it off the old radiator 🙋♀️
@josephkratzer8535 Жыл бұрын
Working on a 2016 Chevy, this video helped a lot. Thanks!
@zemoney9544 ай бұрын
❤Great Info and demonstrations! Thanks
@DAK595 ай бұрын
I just replaced my radiator. Getting them out wasn't bad. I used a pick. Getting them back in was a pain. I didn't use assembly lube. I just used a little ATF. No leaks.
@carpediem4413 Жыл бұрын
Just did this on a 2011 JL Wrangler to replace rusted/leaking lines with new ones. Couple things I learned: 1) Old rusted lines at press in fittings don’t allow a quick disconnect tool to work (had to use two picks). 2) To get clips out manually, had to soak clips/fittings in PB blaster and work them to loosen the clips. 3) Scraped out the fitting edges for a while around the line press fit to get rust out and PB blasted again. 4) used one pick to press between line & clip bump out to push it outward so I could hook clip from outside with other pick. Longhandled needle nose pliers are a must for grabbing clips, etc on this job. Here’s where it got even harder…😢 5) after clip removal Fittings at radiator were rusted in place and would NOT come out… Kept at them with PB blaster and grabbing metal line with Longnose pliers and cranking back and forth to eventually pull the lines free. Was tough and took at least 10 mins of wiggling forcefully while pressing outward on the line… PITA. I heard some people recommend cutting lines and using a deep so it to remove fitting body… my fitting body just spun near radiator as it seems like a compression fit at radiator tube… I didn’t want to mess it up so left it… spinning that fitting nut without cutting lines might help to break the rust free from the stuck line … but I just kept using the long handle needle nose and wiggling and pressing til it eventually popped out. Removing lines at trans much easier. 6) Had to do some slight bending of the new lines to get them in correct shape and fit so they didn’t rub on anything or each other and didn’t have odd angles or tension when fitting them into the clip fittings… you want the line end to push straight in and pop in all the way so the clips can be installed and hold get in front of the line end flanges so the lines wont pull out. Test pull these after you get the clips reinstalled. 7) Reinstalling clips was sorta a pain because you had to make sure the lines were fully seated so the clips got in front of the line flanges to hold them in… the clips have 3 bumps or spots the snap in to holes on the fitting clip channel. Hard to see but the center clip goes into the short hole (channel) and the end of clip slide into the longer channel hole openings. 8) Test pull on line and make sure clips are fully seated into fitting as evidence by clips being full down into the channel and not protruding (needle nose to make pure they are pressed down fully.. if not the line flange may not be all the way pressed in - must press in straight which might require a slight line bending). 10) once all closed in a pull tested, start engine and check for leaks. 11) no leaks push plastic cover back over clip fittings (might need to use a bent nose long handled needle nose pliers as I had to put tip on either side of plastic cover and give it a hammer bump to get covers to seat fully. 12) Install line plastic retaining guides so lines don’t rub on anything or each other, hit anything or press against any other parts. 13) replace the amount of fluid you caught in pan when you pulled lines.
@katscan9114 Жыл бұрын
Dude. He should have showed the install too. That's my issue. Nonetheless. I'm halfway there.
@ralfie88019 ай бұрын
I know it’s late, but after you get the lines sliding freely in and out of the fittings with plenty of slickum, put the clip in the fitting and then snap the line into the fitting. You’ll hear it click when it seats, then pull on the line to make sure it went all the way home.
@MrJwarren100 Жыл бұрын
Thanks for the low down on the clips and the Goo. Just ordered a tub from Amazon.
@phillipjarrett78625 ай бұрын
"It's not east getting to 1,000 subscribers" he says. One year later he's at 84k subscribers. Good work my friend.
@WrenchingWithKenny5 ай бұрын
I appreciate your kind words. Thank you for watching & keep wrenching 🔧
@ricenglebretson29425 күн бұрын
Wish I would have watched this before I tries to replace the entire nut on my external cooler. Missing clip blew off the line. Put a wrench on the nut with very little effort peeled the cooler right open. 150 dollars later for a new cooler I decide to watch for some kind of tip. 25 years fixing euro cars didn't learn me nothing about these GMs. Thanks
@paulwindisch14236 ай бұрын
At the dealer, we always used Transjel brand. The stuff I used was gold in color. Used it for lots of stuff. O-rings, injectors, trans lines, etc. The main thing I used it for was "gluing" check balls into valve bodies and "gluing" spacer plate gaskets to spacer plates. Even as a trans guy at a dealer, one tub would last me many years. As far as the release tools for the lines, I did end up with one that works well and I still have it to this day. I think it is Matco branded. It never gave me issues unless the trans line/fitting were extremely corroded, then I used your pick method.
@joshuaatkins51973 ай бұрын
This is a pretty good explanation. I'm not having any problems getting the clips out. It's getting those lines to reseal after putting them back in. I may look for a barbed fitting that will go into the radiator and just run a rubber line
@kc816_9 Жыл бұрын
Nice video well explained I'm dropping my first transmission and the only thing holding it in is the lines thank you glad I just found this video 👍
@charlesdunn16911 ай бұрын
Thank you I have a 2001 GMC Sierra am replacing the trans lines I spray WD-40 on the nuts thinking it would loosen them watching your video I see that there are clips to take off thank you so much for the easy removal
@ArnieAlmaraz Жыл бұрын
Thank you.for make time to do these tips. Ik about to replace my radiator....
@jameswhite1319 Жыл бұрын
Thank for sharing I got a North Star engine and the transmission line is leaking and just had the transmission fixed so I going to do this myself, thanks again! Houston Texas
@jwendt20036 ай бұрын
I replaced both lines on my 2013 Town and Country. Left the clips in when pressing/forcing the hoses in. Thought they were all clicked in, but blew out 2 hoses 2 different times. Finally took them all off and installed them the opposite way. I reset the hoses first, then the clips last (one by one). That way I can tell better that the clips were actually set behind the hose ends where they should be, instead of forcing them on with the clips on and hoping they 'clicked' in.
@clrd4tkoff3 ай бұрын
Great Video!! Thanks for the information!! 👍🏻 👍🏻
@cansee2465 Жыл бұрын
A year ago trying to get 1000 and now at almost 60,000! Congrats!!
@davidgrubb7287 Жыл бұрын
Great information!
@migo831 Жыл бұрын
Thank God for youtube. Lol. I was wondering how get to the clip itself was about take off the line from transmission. Great video saved me. Now I can drop it and get it rebuilt. Lol👍👍😎😎
@manuelelliott1479 Жыл бұрын
Thanks for your video. I have a chevy truck with leaking O.ring. Video was helpful
@jeffb2439 ай бұрын
Getting ready to put a radiator in my 2004 Grand Prix GTP this weekend and was dreading messing with these damn transmission line clips! Getting them off isn’t too bad, but I was REALLY dreading putting them back on! Nice tip about the Assemblee Goo!!! Not dreading it as much now!!
@mikea1973 Жыл бұрын
They are called 'jiffy tight' fittings..in my opinion the correct tool works great just lube with blaster on the fitting first..install the correct size release tool and twist 1/4 turn and pull line out..lube with grease to install..makes a good seal for the o ring in female fitting..
@kendocashwell45376 ай бұрын
Once again, words of wisdom shared. As far as "tool" evaluations, don't hold back Sir ! Tell us what you think.
@tonywestvirginia8 ай бұрын
Think about it. The plastic collar is to keep the dirt and grime out. The clip if installed properly will not come off.
@sandyblue42353 ай бұрын
This was very informative. We were putting a clip back on and it's not easy. Somehow the clip came off and lost transmission fluid.
@24roughing76 Жыл бұрын
You are well past 1k now 😂 I'm getting ready to replace the remote oil lines on my 97 4.3L this week. Thanks for the advice on the clips.
@44hawk28 Жыл бұрын
Transmission assembly lube and Dielectric grease actually works quite well for putting those things together. The Super Lube is an example that works really good. Had just enough to touch on your finger and wipe on a piece of metal, you would not believe how much Slicker that metal becomes. I have used it for Sears on firearms. And a slightly better version of it that lasts a bit longer, is the CRC black brake Lube. I've got a jar of that I bought in 2007 or so. I still haven't used it all. I literally use it sometimes on the tip of a toothpick.
@von_rva9907 Жыл бұрын
Definitely subscribed .. finally crossed this video... No I know why my 02 Denali lines are so loose at radiator..most likely no clamps from previous owner 😐
@vicpetrishak77058 ай бұрын
The transmission retaining clips may also be secured with a nylon zip tie .
@michaeltreglera67046 ай бұрын
I actually used a small hose clamp works good
@shardeaorr9137 Жыл бұрын
My papa always said if it's there it's there for a reason girl....🤦🏿♀️😂🤦🏿♀️😂🤦🏿♀️
@kluno196610 ай бұрын
Thanks, great advice! It helped a lot!
@CruisinComPTon2 күн бұрын
I had a zip tie substituting for a collar for years. Got rid of the car with it still on there
@robpaul7900 Жыл бұрын
Assembly goo is mainly used for transmission rebuilds you can use it for seals too but usually I use trans fluid for all o rings gas oil any o rings trans fluid is good for all that. One I like more for o rings from assembly goo lubegard treatment comes with a brush and is much thinner and runny looks like clear color that green is one of the thicker ones blue is thinner too.
@valiant7357 Жыл бұрын
Damn bro now you have almost 28k subs And now 1 more. Great job
@backnine9 ай бұрын
Plastic cable ties work great.
@victorgalarza9296 Жыл бұрын
Thank you. I really appreciate it for you help
@589gang2 ай бұрын
Thanks for the info sir 🫡
@brandonstallard22 Жыл бұрын
You can also snap the line back in with the clip in place, it's designed for that
@DependableAutoTruck8 ай бұрын
i just use the removal tool i have for those slip in turn 1/4 turn pull line out and when replacing just push like back on and reinstall cover never loose clip or stretch clip from using pick
@scratch1872 ай бұрын
Nice to see you exceeded the 1000 aubscribers!
@billbaker462711 ай бұрын
Honest discussion
@nickvevang4613 Жыл бұрын
Rock on dude you're now over 60k subscribers lol
@makfive34313 күн бұрын
I had hart time to remove those clips, as on my Cadillac there is very poor access to them, so I decided to unscrew nuts from radiator instead. Bottom nut came out easy but while unscrewing top one something broke inside radiator breaching barrier between engine coolant section and transmission oil section causing coolant to leak out through open bottom transmission line. Had to replace whole radiator. That should never had happen. My guess is that radiator was 10 years old and very "weak".
@Ramrock325 Жыл бұрын
Thank youuuu!!!!
@maliamaxcy7065 Жыл бұрын
Hey Kenny. You Are dead on on the trans assembly lube, I've used Vaseline for many years and it's pretty good, but the assembly lube works so much better it doesn't make sense to use .And as you pointed out one tub will last roughly 2.3 lifetimes unless your shop is as messy as mine and you have to go buy another tub. that's the only way your original will turn up, generally, the second you get back from the parts store. I now have 4.6 lifetimes worth.Keep on wrenching.
@raincloud547 ай бұрын
The oring sticks to the pipe. Busted my knucks more than once
@antonbende8210 Жыл бұрын
Good and nice to follow ! 👍
@zu15027 ай бұрын
1 year later at 70+k subs nice !
@maxrockatansky12712 жыл бұрын
i was trying to smash the clip on till i found this video… put clip first then hose :)
@darksidestudios424 Жыл бұрын
We are working on our Chevy Silverado 1500 mess up radiator putting a new Radiator in working on the cooling line and transmission line with the cramps you were talking about I am having some issues putting those clamps on line
@WrenchingWithKenny Жыл бұрын
I'm guessing you got them on. If not, try posting your detailed issue on one of my Facebook pages, Wrenching with Kenny or Backyard Mechanics (answer all the questions for ByM). There are people on those pages all the time that will help. Thanks for watching!
@james10739 Жыл бұрын
I have always pulled the clip but I saw someone using a tool like for fuel likes or something and I had no idea but it seemed a lot easier
@thepiedish90310 ай бұрын
Yea I got two things out of this video. Thank God I don't need those clamps because they went to the moon. Second it made me realize I forgot my hose clamps...
@ralfie88019 ай бұрын
I’ve had the best luck getting those clips loose with a plain old flat head pocket screwdriver.
@chriscandelaria1175 Жыл бұрын
Thanks
@bubblusangha6 ай бұрын
To those wondering how to install it, just slide the clip over it, nothing through it
@markg33056 ай бұрын
Thank you
@thegrey86434 ай бұрын
I have always hated these style connectors for the last 18 years doing this shit, especially when it comes to compact turbo cars. Getting them off isnt the problem, its getting those damn clips back in place in a cramped engine bay of a compact car. Trucks are stupid easy, cars not so much.
@WrenchingWithKenny4 ай бұрын
They are a huge pain in the butt. Thanks for watching & keep wrenching 🔧
@ronwade56465 ай бұрын
Here in Flagstaff those connectors get full of cinders and won't release!
@katscan9114 Жыл бұрын
Missed opportunity. Video of clip install. Yeah i heard what to do but orientation etc would help too. Nonetheless good video.
@thomask48362 жыл бұрын
Hey, Thanks Again! Funny story, when I picked up that 2013 Explorer 300 miles away, my Saturn cooling system failed en-route. I have my 2008 Saturn Vue in the garage now for what I think is going to be a radiator (hopefully not just a hose). No rush, but the last time I did radiator coolant lines, there were no clips. I appreciate you doing this video Kenny! I did notice the retainers moved them back. Thanks so much for your useful information on the clips!. Once I get all of my tools in the new tool cabinet and cart (they're getting a good cleaning before they go in), I'm going to yank the condenser and the radiator's next. Any advice on how to deal with lost trans fluid? This car doesn't have a tranny dipstick. Take Care, Tom
@WrenchingWithKenny2 жыл бұрын
I did a video a few months back on a Saturn Ion being low on fluid. It should be the same for the Vue if I'm not mistaken . The video can't be from more than 4 months ago . Let me know if you can't find it
@markhuyette85098 ай бұрын
Snap On tool works good
@alexandrepoirier7125 Жыл бұрын
Thanks a lot!!
@FUMan6618 ай бұрын
I just broke one of those collars/clips on my Hummer. 🤬 I was told to pry it off, I wish I knew all I had to do was rotate it. Can't find a new one online anywhere. So you say a small hose clamp will work? This is frustrating! Thanks for the video!
@MrAppalachia4 ай бұрын
Nobody in town carries those dame collars, hose clamp it is lol
@HypeTv1002 жыл бұрын
what happenes if i dont put the plastic piece back on ?
@rockzhard20092 жыл бұрын
Kenny, would it be possible to request a short video? on the Silverado there, since it is tore down to it's current point, could you make a quick video showing the heater core replacement? basically just pulling the heater core out. if so, thanks, if not no biggie.
@GregsAutomotive8 ай бұрын
Or you can buy a master quick release set, or the specific quick release tool. It bothers me that there are no vids on correct usage of the correct tool. Pick works, but really isnt correct. Guess ima figure how to use this myself
@coyoteserranoband9 ай бұрын
Hell in a handbag...still got a leak from that fitting...
@jayozzman2909 Жыл бұрын
How do you get the little clip back on???
@PandaMan026 ай бұрын
that plastic collar shouldn't really be retaining the clip, the collar is there for a similar reason as the assurance clips on electrical connectors. if the plastic collar doesn't easily seat over the metal clip, the line either isn't in all the way or the metal clip is stretched wide and won't secure the line.
@Flatlandproductionz Жыл бұрын
I save those clips for extras.
@frez777 Жыл бұрын
just like removing a window crank from the days of yore
@669garagecarleeodom5 Жыл бұрын
Yes sir. Nice
@budthechud34082 ай бұрын
The black covers for the quick connect,are they critical? I have one that is loose
@brandonstallard22 Жыл бұрын
I used a metal hose clamp and it came back off and dumped 5 more quarts lol I used a plastic zip tie and she held for a 2hr drive back home. Where do we get the oem plastic clips? They look like those plastic things under a coke cap
@jasongilliland95089 ай бұрын
Hey thanks for your videos. What about replacing the clips? My truck is really clean, a stone bounced up and cracked my lower transmission cooler line. I got the clips off no problem, but after replacing the lower line I'm having a hard time with the clips. I want to leave the fittings in the radiator and transmission. I thought it would be easier to replace the clips and leave the fittings. Any advice you can give would be great. I'm a new subscriber.
@garyesada5766Ай бұрын
I have a chevy hhr. Does the trans fluid need to be drained to replace the cooler lines.
@WrenchingWithKennyАй бұрын
@garyesada5766 No. You will lose some fluid though. Check the fluid for sure when you're done the repair & adjust accordingly. Keep wrenching 🔧
@epia12511 күн бұрын
What size are those clips 3/8:
@Fear203 Жыл бұрын
Kenny Help! The clips stick out past the connector and the collar will not go back on! Had two lines blow off now and not amount of force or cursing will get the collar seated.
@tylivinlife2238 Жыл бұрын
Mine oil cooler line is currently leaking pretty good (the top 1) and the black clip is not even attached its slide down line. Is it possible thats why its leaking?
@WrenchingWithKenny Жыл бұрын
It's possible if the line is leaking where it meets the radiator
@tylivinlife2238 Жыл бұрын
@@WrenchingWithKenny its definitely leaking there rub your fingers on it and get oil and you can see where its been dripping when driving or parked
@WrenchingWithKenny Жыл бұрын
@ty livinlife , my only concern would be a possible knick or distortion of the line where it goes in the radiator. It is uncommon to have a leak there , but not unheard of . You can get a replacement fitting for the radiator, you just need to be careful as the fitting seals the cooler to the tank , so possibly creating a coolant leak can happen. In all honesty, if the line itself looks good (no nicks or damage) , if it were mine , I'd probably replace the radiator
@bodawaykahgegab Жыл бұрын
My top trans cooler line keeps popping off second time only awhile driving and seems when I got on the throttle it popped off my guess is the black clip is damaged? Idk how it keeps popping off it feels sturdy when I pull on in and such after installation any ideas please get back to me, or where I can buy a new black clip and possibly w clip
@tylivinlife2238 Жыл бұрын
@@bodawaykahgegab could be clip or in my case the inner rubber wore out
@DaBoulAb Жыл бұрын
So, I have a 2018 Chevy Malibu and I got in an accident and had to replace all three off my radiators and I’m having trouble with keeping the trans. cooler line in place, it’ll keep popping out. Any suggestions?
@WrenchingWithKenny Жыл бұрын
It's Mrs Wrenching. I'm glad you're OK. You need to use a ziptie or hose clamp to hold the lock clip in place. Kenny has a video about it... look for the S10 oil cooler line that kept popping off. I don't remember the name of the video though. He published it within the last 6 months. If you can't find it go onto our Facebook page wrenchingwithKenny & ask on there. You will get a few suggestions. Stay well. Keep wrenching 🔧 Meg
@timeless6964 Жыл бұрын
What About the O-- Rings?>?
@jacobguzman4311 Жыл бұрын
If I took the base bolt off instead of clip will it be ok when replacing radiator?
@1shredderx8 ай бұрын
This shows the incorrect way to uninstall, and shows nothing about reinstallation (the hardest part when you do it his way). When you remove the clip like this, it bends it. It is not necessary to remove the clip. When you reinstall it, just slide the line in until it clicks back in place. Pull it to ensure it is seated.
@josepha6123 Жыл бұрын
Hello Kenny, are the plastic caps replaceable or built into the lines? And is the best option a hose clamp if mines not fully locking
@tombowen3640 Жыл бұрын
I assume it would be the same for a cooling line for a turbo?
@WrenchingWithKenny Жыл бұрын
Depending on application, bit if it's the same style, then yes
@freshmaker5 Жыл бұрын
The assembly goo is for o rings in general or to put on the end of the trans cooler line? Doesn’t look like there is an o ring on the line?
@WrenchingWithKenny Жыл бұрын
The O-ring is inside the fitting that the clip is in . And yes, the goo is good thing for pretty much any o-ring . I've used it on injectors & fuel regulators , transmissions , power steering , cooling systems etc . Pretty much any mechanical system EXCEPT BRAKES where it could come in contact with the fluid .
@freshmaker5 Жыл бұрын
@@WrenchingWithKenny thanks. I have a small tube of o-ring lube. Maybe I’ll try and put some of that on the trans line before I clip it in. Thanks
@WrenchingWithKenny Жыл бұрын
@@freshmaker5 it will help for sure ! Thanks for watching !
@shawnalexander1158 Жыл бұрын
Mine won't go back on for the life of me. Im beyond upset
@cyrus7210 Жыл бұрын
Getting them off can be a struggle..... getting that freakin' line back in....worse thing I've dealt with..yeah..do this,put the clip on first...put your finger...spin that ...turn around...get a doo dad....screw all of these tricks for trickin' yourself into thinking you got it. Here's a solution...tubing cutter,flare tool and correct brass fittings and line wrenches... don't fool yourself,you can cut,flair and assemble these fittings quicker than you think ,but guess what....the Fu;-kars are back together leak free and you've moved on to the next thing. Try it, I swear it got me an hour or better ahead. Remember these clips were meant only to cheapen the manufacturing process, not for disassembly and repair...
@Shadow0fd3ath249 ай бұрын
Whoever came up with making these spring steel that SPROINGS off like it does should be FUCKING ASHAMED of themselves for making them such a pain to get it back on without it doing that. Such a stupid idea despite being so "easy"