Traverse Adjustment | Part-2 | Complete Calculations (Solved Example)

No video

Traverse Adjustment | Part-2 | Complete Calculations (Solved Example)

Рет қаралды 7,996

Ziad Abdeldayem

Күн бұрын

Пікірлер: 22

@jacksonkaruiru5638 2 жыл бұрын

Great work. I remember these corrections back in campus. Thanks for the enlighten and of cos refreshing our mind.

@mubasherhassan440 2 жыл бұрын

Very nice sir. You explained in detail and in very easy way.

@jamesardinez9923 2 жыл бұрын

Great and easy way. Thank you very much for the lecture. Godbless.

@ziadabdeldayem6884 2 жыл бұрын

Thanks.

@user-ff8ju8kd3e 22 күн бұрын

Hello Dr,ziad I was looking for app that gives reduced levels from when we input the bm value

@uncertaintyprinciple5430 4 ай бұрын

@ziadabdeldayem6884 Hi Mr. Abdeldayem, In this video, WCB ab does not match the coordinates A & B given, there is an angle error of 8" ?

@phemelothatochabaefe9631 Жыл бұрын

Salute...!

@ziadabdeldayem6884 Жыл бұрын

Thanks.

@jamesdean1005 3 жыл бұрын

Thank you !!!!!

@landsurveyoralaaahmadhafda1313 9 ай бұрын

how you got the WCB of AB?? If i we have a new project and only 1 known point from where you got WCB of AB??

@uncertaintyprinciple5430 4 ай бұрын

It's impossible to have only one point. You will have at least 2 points, but never accept 2 control points from anyone even if you get them from local authorities, always ask them for at least 3 control points. At least you will have a Resection methodology on how to calculate a 3 angle triangle 😉 Note: In this video, WCB ab does not match the coordinates A & B given, there is an angle error of 8"

@mubasherhassan440 2 жыл бұрын

Please make one video on solution of compound curve also, thanks

@ziadabdeldayem6884 2 жыл бұрын

I will try when I have some free time.

@Silentwarzone 3 жыл бұрын

when you say "always start on a point with known coordinate" how we come about knowing the coordinate of that point if not given on paper like on your example? Is it ok to just make up a coordinate if is local network?

@ziadabdeldayem6884 3 жыл бұрын

The starting station might be a Benchmark (a point with known coordinates). The surveying agency in each country has established a lot of Benchmarks to cover their lands. For local projects you can use an assumed value for your Benchmark (starting point).

@Silentwarzone 3 жыл бұрын

@@ziadabdeldayem6884 understood. a lot of building setting out are local. so by the way, what is the method of actually correcting those coordinates once you work out correction of angles and distances? are the new coordinates corrected in the total station and then marked on the ground/pegs?

@rashmijailani2303 3 жыл бұрын

@@Silentwarzone I need this answer too. Hey Geomatics where are you? Come out come out wherever you are…

@uncertaintyprinciple5430 4 ай бұрын

@rashmijailani2303, @Silentwarzone Guys do you know what traverse adjustment means before asking this question????? Before starting work you will get at least 2 coordinates from local authorities... but never accept 2 control points from anyone even if you get them from local authorities. You must ask for at least 3 control points. With 3 coordinates you can do Resection and check the accuracy of the 3 coordinates, if they do not match each other do not accept the control points and ask them to check again. When everything is OK you can start creating new control points and when you have created a loop with new control points you can start the Traverse Adjustment Method!