Hey, thanks for the love 🙏! This subframe rebuild is looking awesome. Keep up the great work man!

I'm a simple man. I see a guy playing with fire I upvote.

Man, your car is so well taken care off... I'm proud of you.

A better way to remove the bushings is to heat up the subframe around the bushing till the rubber starts to melt, then just hit the whole thing out with a hammer, took me about 30 to remove all 7, really easy

Great video man. Your really good at moving the story along so its super easy to watch. Looking forward to the next video!

I always like you more and more after each video, great content, keep it up mate! 👌

lmfao didn't expect that quick reggae segment

That 's some true E36 love over there (beats engineers at the BMW dealer for sure)! Paintjob looks good. If you can't get all rust out, you can get a converter over it. I work at my E46 coup and my E36, this really gives me some inspiration to go on, keep up the good work!

your videos just keep on getting better, man. Keep up the good work! i used this to replace my rear trailing arm.

I've been waiting for this!!!

Those bronze rims look good especially with the blue gray paint👍

Gavin your the man ! Really inspiring me to do the same thing to my E46 M3. Can’t wait for the next video man ! Keep up the good work !

I love your channel mate! I am also taking care of my e36 :)

Another great video. 👌

This is great! Except killing it with fire, that was fun 🤣 Really props to taking this on your own. Good job, keep it clean! Cheers

Just replacing the old bushings to even stock Factory new ones would have improved the ride immensely. I'm worried that having all poly bushings back their is going to create a very rough ride and every vibration is going to transfer and you may not like it. It will definitely stiffen everything up and you're going to feel it for sure! ...but if that was a daily driver, you might regret hard poly bushings. Just my humble opinion.

subed. really good video

I think I’ll use the stuff for gas tanks for the rust removal.

5 yrs ago seems to be most e36 videos. Soon we will have more from meeeeeee.

I can't wait for winter to be over and start working on my e36

Great work. I'm wondering how the paint would hold up in the long run. I did a bunch of frame braces for my Maxima and rattled can it, few weeks later the paint started to chip off despite the careful paint prep. I would seriously get it powder coated, especially when you already invested a ton of time and money for new parts too. To cut down on the cost, clean it as good as you can, especially the rust so that they don't have to bead blast them too much and look for common high demand color. I'm also in the process of doing similarly and plan to powder coat the sub frame, the control arms, trailing arms, and the diff housing.

please buy yourself knee pad it will help. great vid p.s the knee pad is basically foam board about 2x3 and you place it on the ground prior to working on your knee/knees

Your video inspired me to do the same procedure:) I am a Little curios about the handbreak wires, where they hard to refit?

where did you get the new front screws for the diff ?

hey bro did u use hi temp paint on the diff and subframe or no?

when you are done with the rebuild make a list of all the parts that need to be ordered?what you ordered

did the paint dry/cure ok? spray painting outside with freezing temperature would concern me a bit, but great job, I wonder if BMW have a tool to remove the bushings?

You really don't need to burn out the bushings. Just heat the outside metal for about a minute then whack them with a hammer. They will pop right out.

I only need to do the sway bar reinforcement plates if upgrading sway bar right???

Bro what is your occupation

Is it expensive to rent one of those units?? Are they 24/7? Nice rebuild!

update? how much difference did it make?

What paint did you use?Can u put the link?

Really thick rust😂

Hitt the like button

prntscr.com/mfhcv0 6:04 YEET mfs 🤣🤣

Oh, the bushing stink.....yummy.

Sloppy

This guy complains alot