Trench Lighter From A 308

Рет қаралды 39,845

Күн бұрын

Hello everyone, in this video i'll show you how i've made my second and improved trench lighter!
Hope you'll enjoy it, don't forget to like this video and subscribe to see more of my projects!
previous version -- • Homemade lighter from ...

Пікірлер: 25

@jameswatters9592 2 жыл бұрын

been in engineering all my 73 years, first time I have seen a drill used as a lathe, neat

@corvotheblack9749 3 жыл бұрын

Nice job dude. I used 2 Remington 7mm to make my lighter. And I used 90 proof vodka mixed with charcoal lighter fluid for fuel

@earnierosenow9834 2 жыл бұрын

at 13 seconds that is a very clever way to lathe something im impressed end result is very clever

@n00blord111 3 жыл бұрын

Magnets lose their strength when subjected to heat, learned that the hard way. I wonder how it held up.

@matsudaindustries2530 3 жыл бұрын

You are right,but to lose their magnetic field they have to reach much more higher temperatures, but it won't here because it is not on direct contact with the flame, and the flame temperature doesn't reach further than 300⁰C ( so far is still holding well)

@n00blord111 3 жыл бұрын

@@matsudaindustries2530 cool.

@matsudaindustries2530 3 жыл бұрын

Np (: it is sure an unusual design, not the best I must admit, the magnet tends to squash the wick and sometimes you have to unfold it with you fingers in order to light up, so still room for improvement but you have to start somewhere 😜

@bluebullgaminghighlights614 2 жыл бұрын

Smart idea using a magnet for a good latch

@legso21 4 жыл бұрын

NIce jub, but isn't the 308. a bit small for this? I made one from a 338. norma magnum a while back and even that feels a bit inadequate, since i have to refill it every couple of weeks or so.

@matsudaindustries2530 4 жыл бұрын

That's right it was quite small, about the same size of the small Bic lighter. Definitely not very comfortable, expecially for my big hands, and doesn't hold fuel as much as a proper zippo, but for the moment it was the only cartridge i had laying around, so i gave it a try anyway. Ps. Possibly the best cartridge to make a lighter of could be a .50 cal or even a 12 gauge, should give it a try whenever i'll find one

@Thicbladi 3 жыл бұрын

Like a zippo every time you need it it’s empty

@stevenpham1961 3 жыл бұрын

@@matsudaindustries2530 can I buy one please

@federalpumas6018 4 жыл бұрын

This is cool but how long can you use it before it's too hot to touch?

@matsudaindustries2530 4 жыл бұрын

Kinda like a normal zippo, the base is made out of solid steel, so it gets some time to get hot enough to burn you. Never tested enough to say exactly tho

@8zzzzzd79 3 жыл бұрын

May I answer? Between 2-3 minutes for me

@clarefabula4588 3 жыл бұрын

His poor wife... No shoelaces or perfume!

@lulpeyote2001 5 ай бұрын

Is removing the primer from the bullet optional?

@onalert413 4 ай бұрын

Primers are not in bullets. The bullet is specifically the projectile. The entire unit of bullet, powder, case, and primer is a cartridge. I doubt you could make a working lighter with a live primer still in the case and even if you could that would be rather dangerous.

@valdemarwidd2149 9 ай бұрын

Juat remember it needs to be cotton shoelace. Plastic shoelace just melts

@eriklittlebigg7440 4 ай бұрын

He also uses the finger from a rubber glove.... Its a real mess. Melts and stinks to high heaven!! What a dummy he is, right!? Too bad he ain't as smart as you.