Thanks man. Sitting here waiting for a week for a plumber to call me back. Think I'll tackle this myself now.

Just what I was going thru ! Great video saved me a lot of heart ache , was twisting and afraid of damaging copper pipe , didn’t realize about set screw👍

I had the exact same problem- your technique allowed me to remove the spout and saved the day (and the plumber’s bill)! Thank you so much!

Thank you for posting this. For the life of me, I couldn't figure out why I couldn't unthread or find the set screw on my tub spout.

Your video, the one and only I found to show the same exact problem I'm having to remove my spout. THANK YOU for posting this!!!

Thanks for the help! I have your identical spout, with the identical problem. Three holes drilled later and I just got it off! Thank you!

I just pulled mine off thanks to this video! I had the same issue where the set screw didn't line up with the hole and couldn't be seen so i was trying to unscrew it not knowing it was in there. I didn't have a drill to use today, so i used a hacksaw and peeled back the part of the spout that was blocking the screw. Thank you! Now im off to the store to buy the replacement.

Thanks! That was super helpful. I knew I needed to get to the set screw, but I didn’t know how to. Now I do. Much appreciated!

I had the exact same problem and this video was the Cure!!! Took 5 minutes to solve after watching the video but spent at least 1/2 hour trying to figure it out before! THANKS!!!!!

THANK YOU! This helped a lot. Will note that once we got t he screw out we still had to twist as it was partially threaded to another piece. But this just saved us having to call a plumber!

Perfect!!! you are a lifesaver - I couldn't figure out where the set screw was

Thank you very much. I was really frustrated with this situation and I was almost ready to call a plumber. But after watching your video, I was able to get it done in 5 minutes and I am relieved that I can now replace it. I'm going to subscribe now and I will look forward to your other videos! Thanks again!

Mine was twisted as well. I had to break off parts of the spout until I could get to the set screw but the plastic on the pipe refused to come off so I had to break that part off as well until it finally came off. Good video thank you! I didn't think it should have been as hard as it was but that made sense after watching this.

Just one more thanks for the video. Same issue on my spout except the screw was almost 180 degrees around. I wasn’t exactly sure where, as I couldn’t see it but got close on the first drill and then just needed to make it wider with two more drill holes. When I first saw your video my first thought was this isn’t going to be my issue but that’s exactly what it was. 👍

Dang, I’ve been putting this off for months. Had to drill 3 holes on the spout before I could find the screw. Got it and it’s off! Thanks man

Thank you so much. Now I feel prepared to deal with whatever might go wrong!!

Thank you! I wouldn't even have had the confidence to know what to look for without this video. [EDIT: Now I need to learn how to solder and sweat copper...purchased the replacements before I knew I know nothing about plumbing. But still glad I'm willing to figure out making these repairs myself with some great KZfaq guidance. And I did know; but now I know even more. ]

This was exactly the video I needed. Thanks! My old spout was apparently identical to yours and I had the same problem with the hidden set screw.

Exact same problem. Would never have thought to drill to get access. Thanks so much!

Watched 4 videos and this was the only one that I got explained everything clearly.

Your video was key to my success!!! Thanks 👍🏾

brilliant!!!! you’re amazing. this was so helpful, thanks!!!!!

Thank You! Drilled it and 2 seconds later on to the next step!

Thank you thank you thank you!!!! Spot on. Exactly what I needed to know.

thank you!!! this was EXTREMELY HELPFUL!

This is EXACTLY the problem with my spout right now, I can see the set screw is in the wrong position. Glad to see I'm not the only one..

Yeah! Watching this allowed us to figure out how to get our spout off.....its collar had turned too. Wish I had seen it earlier....the cooper pipe is for sure weakened.

I tried this and it worked great, the only thing was it took three holes before I found it. Mine was at about the one o’clock position. Thanks again.

Jeez.... This is exactly what I needed!!!!!!

Thank you for sharing and teaching, totally know what to do now.

Excellent video, well done.

Helpful, thank you! I’ll stop spinning it around now and just call a plumber to swap this faucet out unless you’re free this Saturday 😂

Nice job finding that lost set screw. Good times !

Thanks. This helped a lot

Had the same problem, set screw was offset. Thanks a lot

Thank you!!! All fixed thanks to your video 🥳

Thank you! I has this same problem tonight. I twisted the spout thinking it was a screw off type...

You saved me a gang of money Thanks

Thank you! It's my exact spout from 1995.... I never twisted it but the screw isn't showing. I looked first, saw nothing but a metal piece and the plastic flange inside. I twisted it to look at underneath and nothing. Now I know to drill and find it.

Thank you so much that helped me out perfectly.

Thank you. I'm tearing out the old copper and putting in new but I was wondering what size hex key was needed.

Thank you for the wonderful sharing video.

Thanks for the video. Did you make a new one installing the trim kit? Thanks.

You are so smart..really nice faucet

You saved my a$$ on this one. I had to drill 7 holes but found the set screw.

Thank you so much for this sir

excelent, very normal issue. you got it right

You save me from a unnecessary headache

Yes! This is my situation exactly!

I was banging my head on the wall trying to find the set screw. I must have taken 20 pictures underneath to find it. Turns out mine was the twist on type. Was so easy to replace.

I have one (parent’s house) that will neither unscrew nor can I see or feel any set screw. Lord I hate plumbing.

I wish I was as lucky as you. I couldn't figure out where the set screw was, so I used my angle grinder to cut away a ring of metal at the base of the spout. I then bent the ring back and forth with pliers until it broke and I could remove it. That helped me locate and remove the set screw (which was a Philips head in my case) but the spout still wouldn't come off. I then cut the spout completely in half longitudinally so I could separate the two halves and remove it. That left the plastic part still stuck on. It would rotate quite freely, but no amount of pulling or levering could get it to budge. I ended up losing my cool and just burning it off with a blowtorch. The plastic had to almost burn away completely before it finally let go. Turns out there was a thin burr of copper where the set screw had carved a groove in the pipe. That burr was enough to prevent the plastic piece from pulling off. Whoever designed these things was an utter moron.

This helpful video gave me an idea to just saw 1” off the downspout all the way around to expose the allen screw…how on earth did you know it was at that 3:00 position?

Thanks, this worked for me. But I found I have gouged the pipe on the outside because of the set screw digging into it as I twisted. Can I just sand this away?

I installed a new Moen diverter and the dang set screw broke in the unit! I still have the old one but I am not sure how to remove it to get that set screw out and the old one back in. Moen said I needed a plumber and of course they didn't take responsibility for a defected part. Priceless.

Thank you!

Thanks! This video helpled me out a lot!

I was actually able to pull the spout itself off, but the white plastic piece with the screw on it as well as the 4 edged piece won't come off. There's also no screw (I think it's already been removed)...

Thanks!

Thanks a lot

There is really no need and almost every cage to replace the whole spout! My diverter was bad in my tub and shower combination in the guest bathroom, I simply unscrew the knob that you pull up and down on and let the whole diverter come out through the bottom of the spout and inserted a new diverter in and screwed the knob back on it, problem is fixed just like that! I did not need to remove the whole spout or any of that nonsense. If your diverter is bad just unscrew the knob take the diverter assembly out through the bottom of the spout stick the new one in and screw the knob back on problem is fixed! But none of these videos I’ve watched tell you the simple and easy way to take care of your diverter problem for some reason!

Thank you 👌

i have a spout that cant get off it looks like it just attached to the pipe directly and just keeps spinning even when i put locks on the pipe just wont do anything

Spout I want to remove is an American Standard and I don't see any collar at all, just copper pipe with a lot of green silicone trails. Spout turns but will not back off. Should I drill into the spout?

Is there a way to move the shifted "sleeve" or centerpiece to line up with the set screw, instead of drilling holes near the opening. How do you know exactly where the set screw is located?

Brilliant!

I gave a thumbs up because i have a stuburn spout that will not come off with a wierd allen key screw that won't turn and i have the right wrench but it striped it and i did not think drill a whole in the spout because all i have to do is turn it over and you can see the screw line with the whole it just won't turn basically it's froze in there

I twisted the wrong way and didn’t know I had to look for a screw 😭 it’s stuck with the faucet turned to the left and now I can’t get it to move back into place!! I hope I didn’t break it!

Thank you! I was thinking mine did not have a set screw. I could not locate it. I took a grinder to get the spout cover off and discovered whomever installed this old one put the set screw at top dead center. 🤦🏻‍♂️

I'm taking a saw to it tomorrow (just the shell of course), thanks for the help!!!

That is exactly what I’m going through.

I have almost the same kohler spout but, absolutely no access hole to even find a set screw

can a person buy a trim piece like you have, for any tub spout?

How in the world did you know the set screw was off alignment? That was so helpful. Thanks

Worked for me

Thanks. Maybe that's the problem with mine. I will attempt this on my own before calling a plumber. Could a metal cutter work from underneath?

I had a stuck slip on spout... got the set screw out.. all he way out ... flipped it upside down sprayed lubricant in the screw hole and on the copper tube.. twisted it a bit.. and it came right off.

I need help. We took the one off our tub and it’s a screw on to Home Depot to get a replacement and found the one that’s identical to what we have. We get it home and it doesn’t fit. It doesn’t reach the copper pipe. What to do? I suppose grind it down to the original? I have a old house.

I'm trying to replace mine but I can't find the set screw and I can't twist the faucet off. I think the previous owner might have used too much caulking. The wife thinks it's the foam stuff. I'm not sure how to proceed without possibly damaging the pipes

Mine appears to be on same situation and I can't see the set screw but I can't twist the spout around either. It appears to be a mich older system bc I using camera I see no mechanism, only pipe 😥. What could Itry?

Quick way -Just take saws all and cut all way through just behind water comes out . Spout will fall off . You’ll be left w connection point your looking for .

same here!

Quick question how did know the set screw was on that side?

Mine will turn, but the diverter seems to keep it from pulling off any further

Mine is stuck and I had no problem finding and removing the set screw.. Yet it still twists and twists. Hmm wondering if somehow I'm missing this same issue but I don't see how I could be. That thing is on there good! 😫

What is faucet does not have set screw but still just spins ?

I twisted mine and the copper pipe twisted and broke lol.

What can I do if I remove the set screw completely but I still can’t get the spout off?

dp you have to turn off water first?

Mine doesn’t have the screw and it won’t spin counter clockwise either. I rent the house and the landlord is one of greedy people. She won’t replace our spout so I’m trying to do it myself. Please help! Any advice is greatly appreciated 😊✨👍

I don't have a set screw on mine. I haven't tried to screw it off yet. Hope I don't bust a pipe! I have no idea how old the pipes are, but if they're original, they're 84 yrs old.

Probably a silly question - what kind of drill bit did you use? I tried regular and masonry and nothing is making a dent. Maybe I’m being too gentle worrying about breaking any pipes. Do I need to pick up titanium bits?

I can’t see a set screw but mine also won’t turn. Same problem?

Mine doesn’t have a hidden key on there it looks like it’s just stuck at the tip I have it away at way from the wall can’t get it off might just have to saw it off or something

This would have been a perfect job for a dremel or a small oscillating tool. Great job though using what he had at the time.

Sat in my tub, totally unable to twist my faucet. No screw, no nothing. I crave dead

Mine has no set screw but it is not turning

Thank you so much for this video

This just saved me a plumber... 👍🏾

I am trying to take the faucet off of a jacuzzi tub. I found the set screw and removed it with no problem, but now still cannot get the faucet to pull off. It will spin to the left and right, but I cannot pull the faucet up to get it off.