"Do I Really Need POD's?" The Expert answer your looking for!

No video

"Do I Really Need POD's?" The Expert answer your looking for!

Рет қаралды 60,404

Күн бұрын

Ok so everyone always asks me about Pods. Thier purpose is to help raise the transom to draft in less water. Basically run in shallows! In order to get the full effect, you really need to combine pods with a tunnel hull, and a jackplate on the outboard. Whatever you do make sure you get a professional to "WELD" them on. Incorrect installation can be brutal on performance and the overall ride!
Thanks for watching. I have a few new videos dropping this week, and Im going to keep them coming!
Follow Tricked Tins on my other social media accounts for giveaways and special offers👇
bit.ly/TRICKEDT...
bit.ly/TrickedT...
www.TrickedTins...
Follow my Videographer👇
/ ricomarcelophotography
/ ricomarcelophotography
/ _rico_marcelo
Follow SBFISHINGTV👇
bit.ly/sbfishingtv
My brothers company check him out👇
...
bremmyproducts...
bremmyproducts...

Пікірлер: 93

@MichaelCraig-bi3wj 2 жыл бұрын

Good to see someone doing quality work like yourself. Keep up the good work man, people like you are rare now days.

@TRICKEDTINS 2 жыл бұрын

Appreciate it!

@TRICKEDTINS 2 жыл бұрын

(((UPDATE))) THE CUSTOMER SENT ME THIS TEXT TODAY!!! #TINCANKILLER 👇👇👇👇👇👇👇👇👇👇👇👇 "Dude... absolute perfection in all categories. No leaks from install. No water splash over the transom, not even a drop at w.o.t. No crazy slight pull compared to others. Run rpm's up to 6200, smooth as silk. Stable as can be. I jumped up and down on rear bench, waterline didnt even move all. Those angle L's actually performed their job, channeled that lil' bit of intermediate water right on out. Right weld method of installation, The right factory pods made specifically for boat and most importantly The right person with the right skill set putting it all together!! I cant thank you enough for turning this around. Thanks again."

@chrisj2713 2 жыл бұрын

I got backwater pods welded onto my boat. Their customer service was great. Came with simple concise instructions. Super solid grab handles and drain plugs. Keeps my tail out of the water on rough big water so I don't get swamped.

@eduffy4937 2 ай бұрын

Yeah Jake gilk is a solid dude and they make a great product. I've been there and ripped around a bunch of thier motors over the years.

@SouthernStyleLawnCare 2 жыл бұрын

Wow... Dude drilled into a brand new Welded boat..... Good content!

@briangullickson9013 Жыл бұрын

Yeah, I literally had to pause the video at that point and decompress for a minute in total shock. 😮

@blazedhobo8596 2 жыл бұрын

My man got that shop cleaned up and lookin good. That’s what i like to see. 👍🏻😎🔥

@durbeshpatel3047 8 ай бұрын

I had Beavertail small pods welded on a 1448 landau mod v hull by a local (he was excellent, worked for space X). He followed the instructions, and I couldn't be happier. Boat rides soooo much better, easier plane, and same 30mph top speed with 25hp 2 stroke yamaha. Only noticeable difference besides all the benefits is turning is slightly slippery/harder at high speeds, but ever so slightly.

@TRICKEDTINS 8 ай бұрын

Glad it worked out for you. Pods are hit or miss sometimes

@brandonsmith606 Жыл бұрын

The beavertail pods are garbage we make custom pods out here in Utah. They should also angle up slightly. Great job bro doing it the right way

@coffeecup1689 11 ай бұрын

Great welds on the bottom of the pods. They looked better than the factory seams you could see beside yours. Really good advice to have the pods welded on.

@TRICKEDTINS 11 ай бұрын

Thanks brotha. Welding is easy after 21yrs. Running a business is the hard part lol.

@carpturnalnailer 2 жыл бұрын

Awesome!!! Fixing to install some on my Lowe. Glad I watched this!!! You do awesome work man!!! 👊

@TRICKEDTINS 2 жыл бұрын

Thanks brotha!

@tobberfutooagain2628 Жыл бұрын

Yes you needs some pods! They revolutionize the way your boat works! I just happen to have a spare set for sale if you are interested…….?

@juledoren 2 жыл бұрын

I bought a welder just to weld my pods on, now i can weld aluminum

@kevind4021 7 ай бұрын

No need to weld those 16 holes prior to adding the pods. Add the pods by tacking from inside the hull through the holes. Then run a bead around the entirety of the pods like you normally would. In theory that even strong than what you did because you have 16 extra welds. Not that it was necessary but would have saved time.

@TRICKEDTINS 7 ай бұрын

You know how much harder it would've been to weld those holes upside down leaning over the boat. I see your thought process but it aint worth all that effort. Those pods will still be on that boat when im dead and gone.

@Hobothemason Ай бұрын

Putting some on I guess I got a big motor

@TRICKEDTINS 23 күн бұрын

Goodluck

@seandrake7534 11 ай бұрын

So probably a dumb question but here goes if you welded a heavy plate across the pods and built a Jack plate on the back of them would that give you a tunnel hull and allow you to run in less water or would it just F everything up

@TRICKEDTINS 11 ай бұрын

Idk. I think it would need to gradually slope for a tunnel.

@coryboyd7958 6 ай бұрын

Couple of things, 1. Could you push from the inside of the boat to close that gap you were talking about? 2. Its been my experience thats its best if they are mounted half each in and up from the edges? 3. Whats the cost?

@TRICKEDTINS 6 ай бұрын

$450 to weld on if the transom is in good shape.

@coryboyd7958 6 ай бұрын

@TRICKEDTINS thanks. I have a one year old lowe roughneck 1660. Great boat but sits a little low in the back. A 40hp merc, me(215lbs) 6 gallons of fuel and 2 batteries weighs it down pretty good. I'd have you do mine but I'm in Ft Myers Florida. Thank you for your quick response.

@maddgoatee9708 2 жыл бұрын

16 nice size holes on your new transom vs. welding. Hmmm, NO. Well it looks great now.

@rodconner9079 2 жыл бұрын

Let's Gooooooo!!!!! Be Safe

@tsr_outdoors 2 жыл бұрын

Very nice

@mikeelder6298 9 ай бұрын

I personally have an aversion to drill holes below the water line.

@TRICKEDTINS 9 ай бұрын

Preaching to the choir!

@OttoTheWeim Ай бұрын

I’m curious what the cost to have pods welded on like that is? Do you have any guidance as to the cost for this service?

@TRICKEDTINS Ай бұрын

Idk what others charge, but my price ranges $500 up

@OttoTheWeim Ай бұрын

@@TRICKEDTINSthank you for the response. That doesn’t seem unreasonable given the skill level and experience required to weld aluminum.

@CullMeDave 2 жыл бұрын

okay I see you.

@tsjuno Ай бұрын

I have a lower roughneck 1860 with a 115/80 jet. And it has pods. I really want to mount a kicker motor but for the life of me can’t figure out how I would do that. My electric trolling motor just isn’t powerful enough to troll up river and the jet doesn’t turn well at low speed

@TRICKEDTINS Ай бұрын

Idk man. I guess you need some type of extension for the kicker

@JimGrady67 2 жыл бұрын

Quality job looks good!!

@TRICKEDTINS 2 жыл бұрын

Thanks brotha!

@georgekantstandu4501 Жыл бұрын

I fabricated some pods and put them flush to the bottom this created to much lift , so that the motor would captivate unless weight(passenger) would be brought to the back (tiller drive)

@TRICKEDTINS Жыл бұрын

Pods are tricky. Wieght distribution is critical.

@georgekantstandu4501 9 ай бұрын

Did the same thing, should have had the pods about 1 inch off the bottom, to much lift and captivates unless more weight in back

@Unjustified_Bot Жыл бұрын

Why didn’t you use a few pieces of angles to close the gaps? Tack them on the hull and the pod and bring them together with a clamp?

@TRICKEDTINS Жыл бұрын

Why would i do that if i could just fill it with one pass? Adding an angle adds 2 more passes???

@Unjustified_Bot Жыл бұрын

@@TRICKEDTINS if you add an angle “iron” to one, then to the other, clamp the angles with a clamp, close the gap, tack, remove the tacked angles, finish the pass? You might need several angles, but it would only require one good pass and there would eventually be no gap and no warps. Basically - angles, clamp, tack, remove angles, angles, clamp, tack, remove angles, repeat until there’s no gaps and then weld complete.

@talonlacy1302 2 жыл бұрын

Get a spoil gun. Tig the pentrating welds. And cold weld the cover pass on the bigger gaps. Just thinking out loud here.

@TRICKEDTINS 2 жыл бұрын

I have a 1/2 dozen spool guns, nothing like tig welding though? I feel like I have so much more control!

@colestave4573 2 жыл бұрын

Where do you purchase your flooring materials for your builds?

@TRICKEDTINS 2 жыл бұрын

m.facebook.com/fabricsdirect4you

@cheetoz6902 Жыл бұрын

Love the vids bro

@TRICKEDTINS Жыл бұрын

Thanks brotha!

@jhoffman81 Жыл бұрын

Add pods but no jet or jackplate? Seems kinda odd honestly. Edit: Read your description and see that you agree

@tucanman9775 Жыл бұрын

we get checked by the coast guard the power rating is on the vin label

@TRICKEDTINS Жыл бұрын

I've been stopped by marine police a couple times never had anybody check that tho.

@just_chi11in_ Жыл бұрын

Are the channels you added/welded on the inside of the pods to keep water from splashing up!!? 🤔

@TRICKEDTINS Жыл бұрын

Exactly

@coltensawyer6761 2 ай бұрын

Do they slow boats down? I’m thinking on adding them to my 1436 but I don’t wanna loose speed

@TRICKEDTINS 2 ай бұрын

That boat is way to small for pods anyway

@coltensawyer6761 2 ай бұрын

@@TRICKEDTINS ⁠okay I see. I just saw my buddy do it on that size is why I thought it may work. I’m running a 670 Longtail and it’s heavy is why I wanted them !

@coltensawyer6761 Ай бұрын

@@TRICKEDTINS my grandpa has a Lincoln mig welder. It does aluminum and steel you just reverse some leads inside and change the wire we have done it in the past. If I’m welding a boat .50 or so thick what’s a good place to start on my heat and wire feed ? Doesn’t have to be pretty just wanna not burn holes to bad

@robertherbert1306 11 ай бұрын

Will these help with porpoising? Thanks in advance

@TRICKEDTINS 11 ай бұрын

Yes. Its all about buoyancy and wieght distribution

@chadreeves403 Жыл бұрын

Hey man, love your channel. Question for ya, if someone wanted to have you build a custom tin deep v boat, do they sell just raw shells or do I have to buy the whole kit and kaboodle?

@TRICKEDTINS Жыл бұрын

Im sure you can purchase just a hull. You'll have to reach out to the manufacturer and special order. SeaArk makes some nice deep v boats.

@houstone713blastin 11 ай бұрын

Did you have a problem with insulation on the other side of the wall?

@TRICKEDTINS 11 ай бұрын

No foam in the transom? Just wood.

@stevethefishingsanta7771 2 жыл бұрын

What is the real reasoning for the pods? I have a pontoon boat that is 15 ft long with a 40 horse Mercury and I think the motor is too heavy was thinking about adding one foot to each toon.

@TRICKEDTINS 2 жыл бұрын

To add buoyancy to the back of the boat. Main goal is to run in shallows!

@gunfisher4661 Жыл бұрын

The motor is the right size for the toon the issue is these days they are making the pontoons smaller diameter and there fore less weight capacity, It would be just as or easier to add the third pontoon in the middle as a few people are doing now days the benefit far out ways adding length to the pontoons. you can take an old pontoon and customize it to fit or buy a new one as the industry is all ready offering tri toon boats all ready.

@jaymecollier9106 3 ай бұрын

Masking tape is too adhesive! Much better if they'd used blue painter's tape. Nice Job!

@TRICKEDTINS 3 ай бұрын

I agree 👍 💯

@jameslovelace8958 6 ай бұрын

What are they for?

@TRICKEDTINS 6 ай бұрын

Add buoyancy

@normanphair8488 Жыл бұрын

And I know just the guy you can call

@compton3611 Жыл бұрын

Do you think those are strong enough to hold a 200# person on one of those pods?

@TRICKEDTINS Жыл бұрын

Hell yeah. Im 215 and i stood on them no problem. Id bet they would hold 500+ easily.

@kencleg7721 10 ай бұрын

? Pods are for shallow or heavy motors he could probably do a 90 or 115 on the back and still set 4-6 “ of draft so I’d say 100-150 per pod ? Just a guess

@DaDuckman05 Ай бұрын

If you go with a longer boat you don't need the pods.

@TRICKEDTINS Ай бұрын

Sounds good, lol?

@kencleg7721 10 ай бұрын

W the pods I’ll take that 70 so u can put on a 90 ha ha. Perfect size for me express The pods are nice the dog can get in out the back

@TRICKEDTINS 10 ай бұрын

I like Xpress

@tucanman9775 Жыл бұрын

that outboard is way to big for that boat you need pods

@TRICKEDTINS Жыл бұрын

Thats why we put them on!

@kencleg7721 10 ай бұрын

Nahh I got a 60 on mine it’s a 1670 that’s 18’ -20 ‘ I bet she do a 115 know no poblano

@CD38325 2 ай бұрын

I got a 60 on a 16/52 and it set’s perfect in the water with out pods

@eccentricsmithy2746 Жыл бұрын

time is money, could of had this done in a quarter of the time by using a aluminum Spool gun the mig welt them on and still have the stacked dime look. Tig slow af.

@TRICKEDTINS Жыл бұрын

Im good on that. Thanks for sharing tho...