Troubleshooting common Autoscrubber issues

Рет қаралды 152,899

Күн бұрын

Understanding what to look for when your auto floor scrubber isn’t working can save you time, money, and labor. Identifying the problem and cause of your automatic floor scrubber’s issue can save you professional repair costs.
Read our blog article to learn the 6 most common auto floor scrubber problems. www.ebpsupply.com/blog/common...

Пікірлер: 117

@Hensleyken9 3 ай бұрын

Thanks a lot. After watching the video especially that of water not coming out of the scrubber I applied it immediately and it worked ❤😊😊

@weesebowski8651 3 жыл бұрын

Note about the black scuffing lads and cleaning it causes the batteries to die faster! I found the old scrubbers to be more beneficial due to controlling the amount of pressure on the floors! This new 2 button scrubber has stripped waxed floors even with dull red cleaning pads. (Issue!) Also the vacuum hose tends to wear with the arm release. If you use this on average floors the rubber is ok. If you use this in the warehouse on cement floors it chews up the red scrub pads and the rubber...The advanced SC750 ST has had major issues with the battery consistency! You leave it plugged in or not the battery does no matter what. If you leave it unplugged over night it’ll die 3 minutes within the store. The unfortunate part of all this is you have people utilize this equipment not knowing how to properly care for equipment.

@ImperialDade 3 жыл бұрын

“Thank you for watching our content. Sorry to hear you are having trouble with your Advance SC750. Your final point rings true, proper training and machine maintenance is very important. It sounds like there may be an issue with your batteries or the charger - as this is not typical run time for this machine. We find that many machine operators opportunity charge the batteries and lead to very premature battery failure, see this video for more details: kzfaq.info/get/bejne/n96Wg7Fjs8-xlWg.html. We recommend getting the machine serviced. Our technicians are Gold Certified to work on this equipment and can do on site or in shop work on this. If you are within our service area (Maine down to Virginia on the East Coast), please visit this page and fill out the form, we will take great care of your machine. www.ebpsupply.com/service”

@kagome122885 2 жыл бұрын

I hate it when people don't rinse out the tanks and forget to leave them open after use. I once came to work to find the squeegee assembly torn up and missing the steel straps after someone used it to clean up after flooding from rain over the weekend.

@LuisMorales-ll2lo Жыл бұрын

When he pops out the pads I started to laugh 😂

@Bgz8890s Жыл бұрын

5400 Tennant Scrubber-Dryer here. The brush is not lowering when I push the button, any idea where to begin? Thanks.

@khanbadshah4516 Жыл бұрын

We have nilfisk walk behind scrubber dryer... We are facing that the machine brush head is cleaning very hard at right side.... It take too much force to handle... Please guide me whats is the problem how can i fix it.

@Rnpro84 2 жыл бұрын

Great information and easy to understand. Thank you!

@ImperialDade 2 жыл бұрын

Thank you for watching our content, and taking the time to provide feedback! We are happy our message is received well.

@larry762 3 жыл бұрын

Our machine (a 750 model) does not have enough suction going to the squeegee. I've noted that the drain hose is a bit flattened during operation so some of the suction is going there. How do I get all the suction going to the vacuum hose?

@PeacefulPeteable 2 жыл бұрын

I've ran over the hose a few times. A rubber mallet to get it into a round shape, plus some really good duct tape should do the trick. Or a new hose.

@paulz2794 5 ай бұрын

I can understand it better if you JAs didn't have that music playing in the background

@sharla98 2 жыл бұрын

Hello, I have an Advance SC450 scrubber and we are having issues with it leaving streaks on the floor. Usually the streaks look dirty. Do you think this is an issue with the pad we are using or the squeegee blades?

@paulg2100 2 жыл бұрын

Definitely squeegee.. it’s prob not adjusted right or maybe time to flip it or change it completely. First make sure the squeegee is fully clean and see if it streaks still, if it does then move to the other suggestions

@ellingtonwatson3328 3 жыл бұрын

My brush indicator light keeps coming on and off brush stopping at times there is a tiki tiki sounds coming from it.plz help

@davidbarry9474 Жыл бұрын

I'm interested in finding an easy way to put the brush on instead of climbing on my back and reaching under any suggestions?

@ImperialDade 5 ай бұрын

Hello! Thanks for watching. Unfortunately, this really depends on the design of your machine. If you have lugs on the brush that have to fit into the driver, then you do have to reach under, line it up and install the brush. We have seen people put the brush on the floor, then drop the motor onto it and turn it on to lock it in place. However, this is a big NO. This always ends up damaging the machine and leading to costly repairs. Some manufacturers have a design that makes it very easy to attach the brush. For example, Tenant has a great option called CLICK. It involves magnets that make installing a brush effortless. To learn more about this machine, reach out to us: www.imperialdade.com/help-center/general-inquiries

@annetterosin6976 9 ай бұрын

Question: Our T3's scrubber pad is at an angle (up at the front) when lowered and sprays water all over. What can be adjusted to make the scrubber pad level to the floor?

@ImperialDade 8 ай бұрын

Hi @annetterosin6976, thanks for reaching out! There are no adjustments to the head as it floats. We have gathered a few suggestions for you to try and troubleshoot the issue. First and foremost, has the scrubber been serviced recently and had the scrub head removed? If so, then be sure that the head is bolted to the front, rightmost hole in the bracket. If it is bolted correctly, check that the machine brackets in the front are not bent. This commonly happens if the machine was steered or crashed into. If this is the case, we recommend a qualified technician replace the brackets. If neither of these two things seems to be the issue, reach out to us here: www.imperialdade.com/registration Once of our qualified service technicians will be in touch!

@paulg2100 2 жыл бұрын

I have a question , last week or so my right brush keeps not putting out water. When it happens it’s because the breaker keeps tripping. I stop , open the machine , press the breaker and I’m good again. Then about 25 minutes it trips again and I have to repeat. Last week it did only a few times and today I had to press the breaker 25 times or so in a shift. Any reason why the breaker keeps tripping that you may know ? It’s the right side brush if you were standing at the scrubber to use it .. to the persons right .. thx

@Sukimaye Жыл бұрын

I have the same problem right now and I can't figure it out. Have you found out the problem with yours so I could check mine.

@ferneymorenomolina1484 2 ай бұрын

I have a problem, F3 vaccuum overload, how I could fix it? Please.

@barryscott8041 2 жыл бұрын

New on the job, running a Tennant T600e machine; end of shift, twice now the damn thing won't drain the dirty water. Plug is NOT in the outer drain hose....not gonna put my arm in that tank!

@ruudvanelck7083 2 жыл бұрын

My floor cleaning machine stopped adding the detergent to the water. I checked the settings, all fine. The bottle with detergent also full. Any suggestions?

@daytonwallis4258 2 жыл бұрын

Mix the warm water and soap right in the water tank, Works like a charm

@karlvilla9643 2 жыл бұрын

Yes check the bottom for the filter take out cleaning and put it back That happen when we convinated chemicals

@djprojugs6606 2 жыл бұрын

Automatic scrubber not moving on weekends. For some reason employee won't come to push it on his days off. Might need to be replaced soon as I'm hearing strange noises coming from automated part of it. They are high pitched whines sounding like "I've been working for 72 hours straight" and another noise that almost sounds like a " I wanna go home" any ideas how to stop the noises and get it it back to running every day? I tried duct tape but it only muffkes the sounds!

@tomtom3420 2 жыл бұрын

Best comment Projugs!

@samuelseager6785 Жыл бұрын

Looks like we are all still waiting for an answer.

@djprojugs6606 Жыл бұрын

@@samuelseager6785 reapplying fresh duct tape every other day is still the best solution sadly.

@HarrisUltra 2 жыл бұрын

What do you do when the wheels are constantly spinning out and won’t catch traction ? The tires don’t look too wore down so I don’t understand what’s causing it to do that. Please help 🙏🏿

@ImperialDade 2 жыл бұрын

Hi - thank you for watching our content. What type of Autoscrubber do you have (make/model) I'll ask one of our technicians to see if we can pinpoint a problem.

@ImperialDade 2 жыл бұрын

Actually, I got a reply from Dan (in the video) without needing a specific machine model. Here is his response: "I have experienced this from time to time as well. Usually when turning on a wet soapy floor. If you reduce the speed coming into a turn, the machine should get a better grip with less spinning." I hope this helps your issue

@paulg2100 2 жыл бұрын

Also if you have your pad to tight to the floor , for the deepest scrub , it will make the wheels not catch traction. When it’s fully pressed to the floor it is usually just for short periods and not to scrub for long durations which would make the wheels spin out

@edong633 3 жыл бұрын

hi sir,how come no water come out in the machine but before its good enough,but when used in waxing water wont come out properly?

@AMG8241 3 жыл бұрын

Same question but nobody answer

@edong633 3 жыл бұрын

@@AMG8241 I fixed my machine by myself already,it’s clogged What I did checked all the hose and I cleaned the water tank with hot water..

@dmaynard5144 Жыл бұрын

I HAVE A NSS 3330 WRANGLER. IT SHUTS OFF WHEN SCRUBBER IS ON . IT RUNS FINE WITH VACCUUM ON AND SCRUBBER LIFTED JUST STARTED THIS. WHAT SHOULD I CHECK?

@cardboardempire 3 ай бұрын

Check your fuses

@teresapedigo7963 2 жыл бұрын

What might be causing water to leak from the recovery tank into the battery compartment?

@PeacefulPeteable 2 жыл бұрын

Did you already figure out what was wrong with it? Was it a cracked tank, bad seal, or something else? Sounds like a pretty not good issue.

@ScottAllenFinance Жыл бұрын

Could be a degraded tank seal or loose vacuum hose or tank connection gasket. Are you 100% sure it is recovery water and not solution or water leaking from the batteries?

@kathygrzeskiewicz8315 Жыл бұрын

The filter cap underneath the Auto scrubber is on very tight can you give any suggestions how to loosen it

@ScottAllenFinance Жыл бұрын

First, it goes without saying to make sure you're turning the filter cap the correct way. Try wearing a glove with nitrile grippy nubs on it, or very gently using a large crescent wrench to turn the cap.

@ImperialDade Жыл бұрын

Hi Kathy, Thanks for watching! We are glad you found this video useful. You can try using a rubber glove or cloth to open the scrubber cap. If that doesn't work, put some cloth or paper towel around the filter and then carefully use a pair of adjustable pliers to apply pressure until it comes loose. Please note, replacement filter assemblies are usually not that expensive if yours accidentally becomes damaged. If you still cannot get the cap off, reach out to us at the registration link below and one of our factory-trained technicians can help: www.imperialdade.com/registration Don't forget to like and subscribe to our channel so you can stay up to date on the latest videos!

@deaconrodgers5287 Жыл бұрын

At the mall I work at I'm having trouble with our Advenger ecoflex is leaving alot of water on the tiled floor. It's leaving so much water on the floor that I used to collect 3/4 of a tank but now I'm barely collecting 1/4 if a tank. The squeegee is about 2 weeks old!! They were just changed. In the degree tray it's collecting next to nothing. H E L P!!!! I'm currently using white pads

@ScottAllenFinance Жыл бұрын

Sounds like a vacuum issue rather than a squeegee issue. Could be the squeegee vacuum hose or anything in between the vacuum motor and the squeegee assembly. If you pull the vacuum hose off the squeegee assembly, is there sufficient vacuum suction? Start there, then work backwards to the vacuum motor. Check seals and gaskets and make sure no vacuum hoses have come disconnected from the vacuum motor, if they attach directly. If you have good suction on the squeegee vacuum hose, then the squeegee assembly itself may be out of adjustment. There are good videos here on KZfaq that show how squeegees should be properly adjusted.

@ImperialDade Жыл бұрын

Hello! Thanks for watching. It sounds like the issue is that the squeegee is not at the correct angle. Under the back of the machine, there is an adjustment knob. Turn the knob in one direction to change the angle down and the other direction to change the angle up. The deflection of the squeegee blade needs to be even across the entire squeegee tool. It is best to have someone watch the angle as you slowly move forward. Another issue is that the squeegee hose may have a clog, removing the hose and flush to remove clog. Finally, check the gasket at the top of the recovery tank to be sure it is sealing the tank lid properly. If none of these tips work, reach out to one of our specialists here: www.imperialdade.com/registration In the meantime, don't forget to like and subscribe to our channel!

@treavy-n1d 3 жыл бұрын

What if the sc450 nilfisk isnt putting down solution

@maxenergy3600 3 жыл бұрын

that means ur gay

@russvetter4250 3 жыл бұрын

This would be an excellent video if it wasn't for the poor focus. A lot of great information.

@andyromanowski1224 2 жыл бұрын

yupp it hurts to watch it ...

@MrDeviozBeatz Жыл бұрын

What do I do if the machine leaves dirty streaks and leaves dirty water from the hose?

@MrDeviozBeatz Жыл бұрын

And like the water has been full for the past few days

@natechotravels9300 3 жыл бұрын

We’re getting a 03 code. Any suggestion on how to fix that?

@ImperialDade 3 жыл бұрын

Hi - Thank you for watching our content and reaching out. I will ask our technicians. Please tell me the make and model of the machine so I can give them the code.

@natechotravels9300 3 жыл бұрын

EBP Supply Solutions hi! It’s a advance sc750

@ImperialDade 3 жыл бұрын

@@natechotravels9300 Code 3 on that machine is associated with the controls, and disables the: Detergent, Solution, and Brush Motors. You may need a technician to look at the machine. How old is it? It could be covered under warranty. Drop us a message at: www.ebpsupply.com/video-protips and we can continue the conversation and check the serial number to see if its covered.

@natechotravels9300 3 жыл бұрын

EBP Supply Solutions it’s 8 months old. Thank you very much! Someone is coming to check it out today 👍🏽👍🏽

@ImperialDade 3 жыл бұрын

@@natechotravels9300 Awesome! Glad we could be of assistance!

@amielenriquez186 2 жыл бұрын

My machine does stop going in reverse even on idle

@michellemarino63 11 ай бұрын

Why does the scrubber vere sharply to the left side when moving forward?

@ImperialDade 8 ай бұрын

Hello! Thanks for watching our videos! We are sorry to hear your are experiencing trouble with your autoscrubber. If your scrubber is swerving sharply to the left, it is most likely that the scrub deck is out of alignment. Scrub decks can be pushed out of alignment by a bent bracket. This usually happens when the machine bumps into something. If the bracket does not look bent, it could also be a faulty drive system. We recommend having a qualified service technician check out the machine to get to the root issue and recommend a fix. For help diagnosing the issue, reach out to one of our factory-trained service technicians here: www.imperialdade.com/registration

@iapprove8392 5 ай бұрын

Something is not addressed here. Why would the machine slide to the right continuously. Does it have to do with the casters or the main wheels. Those wheels should have some traction to them so when you turn they won't slide as well.

@ImperialDade 5 ай бұрын

Hi! Thanks for watching. There are a couple reasons why your machine may slide to the right continuously. First, is due to worn tires. Worn tires with no tread left should be replaced. Another reason for machine malfunction is you are turning too fast. Tires will spin out doing a full-speed turn. If the problem is not worn tires or the speed of the turn, you may need to check your swivel castors. The castors tend to get hair and lint on the axles and need to be cleaned so the machine pivots easily. Lastly, if there are grease fittings, you should lubricate them periodically to ensure the machine turns seamlessly.

@iapprove8392 5 ай бұрын

@@ImperialDade Thank you for the reply. I will check that out. These new tires for Nilfisk machines don't have treats. I find that is a big issue. And I will check the castors. The machine just goes sideways all the way down the hallway.

@cosmicowl3336 2 жыл бұрын

Machine turns on but no charging icon shows up. I usually also hear a sound indicating its charging but now I hear nothing. any help?

@ImperialDade 2 жыл бұрын

Is the cord fully connected?

@cosmicowl3336 2 жыл бұрын

@@ImperialDade as far as I can tell yes. it's an older machine but was recently re wired and had new batteries placed in it. it turns on fine but when plugged in no battery icon shows and doesn't gain any charge. I've tried just about everything besides taking the thing apart

@albertgeorgy6827 4 жыл бұрын

How can you change the safety connector?

@ImperialDade 4 жыл бұрын

Hi Albert, Thank you for watching our content. The Safety Connector is part of the electrical circuit and not something we would recommend changing on your own. We recommend having one of our factory certified service technicians take a look at your situation and give you a quote. If you're in the New England/Mid Atlantic portion of the US - fill out this form and we'll schedule something. www.ebpsupply.com/service

@albertgeorgy6827 4 жыл бұрын

@@ImperialDade thank you for your response!

@tmae100 7 ай бұрын

Stops in motion for some reason I reset it then it starts what do I do?

@ImperialDade 7 ай бұрын

Hi there! Thanks for watching our videos! We are sorry to hear you are experiencing issues with your machine. We understand how frustrating that can be. Has the circuit breaker on this machine popped several times before? If yes, it is likely weaker and causing he machine to stop. It will need to be replaced. We recommend that a factory trained technician perform this. If you need additional help or would like to schedule a service appointment, contact us here: www.imperialdade.com/registration

@arunrajarunshaiva7089 10 ай бұрын

Sir water not squzeeing and waste water not storing inside but scrabing what is the problem

@cardboardempire 3 ай бұрын

Pull put your hoses and clean them. Sounds like a blockage. Also check your tank. There may be am obstruction of debris

@sarahjohnson-104 2 жыл бұрын

What can you do when you're machine is making weird noise?

@timothyhudson7999 2 жыл бұрын

Put your earbuds in and turn up the volume on Pandora. Or tell us where the weird noise is coming from/what your are trying to do when it happens, etc.

@sarahjohnson-104 2 жыл бұрын

@@timothyhudson7999 the machine was making the weird noise from the front. We got it figured out

@roxannegarcia8105 2 жыл бұрын

Our machine just stopped working what could be wrong?

@roxannegarcia8105 2 жыл бұрын

Detergent button flashing and arrow button flashing also???

@novascotianinfj 2 жыл бұрын

using many Auto scrubbers Professional auto scrubber here 50 hours a week for the last 30 years You guys really need to make that filter much bigger it needs to let more water through Also when you unscrew it Bitstrips very easily because the threading is made of plastic Double the water inflow to the filter and quadruple the surface area of the filter maybe the floors will actually look Streak free Doesn't matter how slow I go how clean the filter is for how full the water flow is there's just never enough water on the floor and I don't have all day Burnish every inch of the floor everyday to get rid of streaks Not your company in particular but the only Autos covers this seem to work or the old freaking giant monsters those were amazing these speed scrub 500 are crap .. Not sure if I can deal this anymore probably going to quit

@skievl23 Жыл бұрын

lmao. what did you end up doing

@liliberaunmacazana6651 2 жыл бұрын

Podría enviar la información en español

@productreviewer9274 10 ай бұрын

I can't get one of my brushes the rotate

@ImperialDade 8 ай бұрын

Hello! Thanks for watching. We are sorry to hear you are experiencing trouble with your machine. We understand how frustrating it can be. If one of your brushes isn't rotating, it is likely that the circuit breaker for that motor may have popped. Something must have caused the increase in amp draw to pop it. We recommend having a qualified service technician check out the machine and reset the breaker. If you need help finding a service center near you, contact us here: www.imperialdade.com/registration

@carlbelt8328 9 ай бұрын

How do I use this scrubber

@ImperialDade 9 ай бұрын

Hi @carlbelt8328, check out this article for tips on how to use an autoscrubber: www.imperialdade.com/blog/how-to-use-an-auto-floor-scrubber

@dixbowman3452 Ай бұрын

T7amr 2d camera never works then randomly pops on.

@ImperialDade Ай бұрын

Hi! Thanks for watching. We are sorry to hear you are having trouble with your machine. We have a team of trained specialists to troubleshoot and repair all types of janitorial equipment. Reach out to us here for a quote: www.imperialdade.com/help-center/general-inquiries?pathname=/

@streetguru9350 3 жыл бұрын

Totally not here because I crashed one and misaligned the squeegee. Sticks out on one side...right turns are death.

@ImperialDade 3 жыл бұрын

Thanks for watching our content. So glad you didn't crash your autoscrubber ;) . IF one HAD crashed it - hope is not lost. Take a look at this video we put together on Floor Scrubber Maintenance - there is a segment on squeegees - maybe this helps. If its bent - then I think you'll need to get the assembly replaced. Floor Scrubber Maintenance: TIps to Extend the Life of Your Machine - kzfaq.info/get/bejne/d6mkiKxnzMiUfaM.html

@streetguru9350 3 жыл бұрын

@@ImperialDade roboscrub 20, designed that way, very tight corner in store with a pillar. It kind of rattles now when moving along the floor, going to attempt to level/align it tomorrow.

@ImperialDade 3 жыл бұрын

@@streetguru9350 Great - hope it works out. If you need assistance from our technicians, visit www.ebpsupply.com/service

@streetguru9350 3 жыл бұрын

@@ImperialDade bolt/nut for adjusting the squeegee height is totally seized from corrosion. Not going to touch it anymore.

@ImperialDade 3 жыл бұрын

@@streetguru9350 Oh no! visit this page and if you're in our area, we can help - otherwise maybe our tecs can suggest a solution. visit www.ebpsupply.com/service

@Hellndegenerates Жыл бұрын

My machine stinks, and I've used my karcher k7 to clean it out using Surfex hd and and various citrus pre wash products, still stinks.

@ImperialDade Жыл бұрын

Hi Deez, Thanks for watching! Did you try the tips in this video? If these fail to work, reach out to us here: www.imperialdade.com/registration One of our factory-trained technicians can help you better resolve the issue. Don't forget to like and subscribe to our channel so you can stay up to date on the latest videos!

@heatherbazinet274 2 ай бұрын

Mine the scrubber part was not working and hard to push. But now it is easy to push but the scrubber jumps like a bunny. Mechanic wad out. Said it was fixed....not too sure what he meant it was fixed? Lol

@ImperialDade Ай бұрын

Hi! Thanks for watching our content. We are sorry to hear you are experiencing issues with your machine. The issue may be with your pad driver. Is it installed correctly? If it is at an angle the scrubber would bounce as the pad driver spins. Please remove and reinstall the pad driver. If this does not fix the issue, contact our service and repair department here: www.imperialdade.com/help-center/help-with-product?pathname=/

@jetclntn Жыл бұрын

my ice machine scrubber won’t drain enough

@ImperialDade Жыл бұрын

Hi Jetcintn, Thanks for watching! We service kitchen equipment in addition to floor machines. This video is specific to janitorial floor equipment. for help or service with your ice machine, reach out to us here: www.imperialdade.com/registration Don't forget to like and subscribe to our channel so you can stay up to date on the latest videos!

@kellydavis8813 3 ай бұрын

No water coming out on floor

@ImperialDade 3 ай бұрын

Hello! Thanks for watching our video! We are sorry to hear that you are experiencing trouble with your autoscrubber. We understand how frustrating that can be. There are a few reasons why your machine may not be dispensing water. First, check the filter. Clean it if it looks dirty. Nect,m check the clean water line. Does it seem clogged or backed up? Clean this as well. Next, check for a blockage in the clean water tank. If you notice buildup, remove it. If neither of these solves the issue, there may be an electrical issue with the water switch or solenoid that releases the water. We recommend reaching out to your local Imperial Dade service center for assistance. contact us here: www.imperialdade.com/help-center/help-with-product?pathname=/

@r0binshaw702 Жыл бұрын

The scrubber wont spin i think its the sensor

@joshuagordon988 12 күн бұрын

Told me nothing

@ImperialDade 12 күн бұрын

Hi! Thanks for watching. We're sorry to hear this video didn't answer your questions or cover the information you were looking for. What specifically did you want to learn? We'll be sure to cover it in a future video. Thanks!

@rodstevenson6326 Жыл бұрын

What's this fella got stuck to the side of his head ?

@ImperialDade Жыл бұрын

Hi Rod, Thanks for watching! Our Equipment Expert Dan, has cochlear implants to help with his impaired hearing. We are glad you found this video useful. Don't forget to like and subscribe to our channel so you can stay up to date on the latest videos!

@romanatodorovic5145 3 жыл бұрын

@ellingtonwatson3328 2 жыл бұрын

Hello my T45B autoscubber brush stop from working nothing from it, before it was stopping an a tick tick sound was coming from it, please help

@PeacefulPeteable 2 жыл бұрын

@@ellingtonwatson3328 I'm taking a total stab in the dark, but that sounds like it could be something wrong with the mechanics of the scrubber arm. Or something could be caught up inside there. But it really sounds like a technician job. I can't think of anything that would cause the brush to stop working if everything is attached properly.

@thedude1249 2 жыл бұрын

✨What is growing out of your head bra? 🤢🤮🤮

@ImperialDade 2 жыл бұрын

Hi - Thanks for watching our content. Dan gets this question quite a bit and we are always happy to answer. Dan was 100% deaf, the plastic pieces you see attached to his head are cochlear implants that give Dan his hearing back. Without the surgery and implants, he would still be deaf, so not a day goes by where he isnt thankful for the procedure. Thanks for asking and we continue to spread the good word about this procedure.

@samuelseager6785 Жыл бұрын

@@ImperialDade That was a very civil reply to a very rude comment.