Truss Blocks and Interior Web Bracing

Рет қаралды 53,073

6 жыл бұрын

Пікірлер: 13

@gary24752 2 жыл бұрын

Usually there is "X" bracing on each end of the building truss web members and in the building center depending on how long the building is in the center of the truss along with continuous lateral bracing on the bottom chord at max. 10 ft. centers. Follow the certified truss drawing for required bracing.

@dtm8073 2 жыл бұрын

Yes, you're absolutely right with "X" bracing at each end and in the center but not exceeding 20' apart. So therefore, if your building is 40' long the distances explained here is perfect, if your building was 50' long you would need 4 "X" bracing.

@timothylorenzano8285 Жыл бұрын

Thanks for the video. Do you have any information for bracing a 7/12 scissor truss in a hurricane zone? (7/12 top chord and 3.5/12 bottom chord with an inside span of 42', outside span of 44', and an overall length of 44.5') Can I have the heel of the truss run past the 12" exterior ICF bearing walls 3" and install a 2"x8" as a facia board without any soffit? How would that affect the attic ventilation? Thank you in advance for your help.

@foursyths Жыл бұрын

Each truss package will have all of the bracing requirements for the building. If there isn't a brace called out, you won't need anything more than the sheathing on the top and the drywall on the bottom.

@jerryw62 Жыл бұрын

On the engineering drawing the brace is shown on the inner strut leg, closest to the center vertical strut. On your 3D model you have it located on the middle of the three strut legs. Oversight? Different plan?

@foursyths Жыл бұрын

The truss bracing location will be specified for each truss in the packet that comes with the trusses. Yes, I think the concept would make more sense if I highlighted a specific truss and then showed a 3d version of the specific braces called out. Now that I look at it, it looks like I didn't even draw the other braces on that truss.

@davidcla2457 4 жыл бұрын

When the webbing doesnt match up on one of the trusses like a common truss and it calls for lateral bracing how do you brace it? Just a short block to another truss?

@foursyths 4 жыл бұрын

In this case, you would install the brace from top to bottom the whole length of the web on the inside or negative space of the truss. Laying it in a way that would form a "T" shape. Or an "L" shape. Usually, there is a call out for nailing a brace like this that would be something like 8" o.c. within 18" from either end with 16" o.c. between the ends.

@davidcla2457 4 жыл бұрын

@@foursyths so just a block tying to another block isnt sufficent?

@foursyths 4 жыл бұрын

@@davidcla2457 both should work in a general sense. The specifics would come from the truss manufacturer

@gary24752 2 жыл бұрын

Why wouldn't the truss configuration be different? Either someone messed up at the plant big time or the installation was poor.

@Joe-oi6eh Жыл бұрын

On the interior web braces why are they shown horizontally instead of at 45°s? I'd think you would want the angle for sheer strength, your roof is relying on your end kick board this way if I'm not mistaken

@foursyths Жыл бұрын

Good question. 😊 On this particular house, the truss manufacturer did not specify any diagonal bracing needed on the inside. I assume that any sheer value required for this project was satisfied by a combination of roof sheeting, gabel "k" bracing (that is what i call it. I think you referred to this as a kick board), and the truss blocks. I build in Utah. I haven't seen any houses needing interior diagonal bracing. Have you seen diagnals called out in the area you build in? Here is my other video about "k" bracing. kzfaq.info/get/bejne/rch5jJR6lr7NkqM.html