Soldering Basics - Popular Solder Connections

Рет қаралды 1,966,660

9 жыл бұрын

Several types of popular solder connections shown. These are commonly used in things like cars, boats, trailers, RVs, motorcycle wiring harnesses, solar projects, low voltage yard lighting, drip systems, crystal radio antennas, etc.
SOLDERING BASICS VIDEO: 4 Steps to Good Solder Joints
• Basic Soldering For Be...
The equipment is nothing fancy - it works - but better equipment makes soldering easier and more fun. The big soldering gun is an ultra-cheapie from China - supposed to be 300 watts but I think it's actually more (note the tip turns red hot in some videos!) The little soldering gun is also low cost, at 30 watts with a 120 watt, 30 second boost in the trigger switch. The solder is rosin core 60/40.
WARNINGS:
- Soldering can be dangerous. If you do not know soldering safety, learn it or don't solder.
- Never solder live circuits of any type.
- Soldering house wiring, power wiring, etc. is outside the scope of this video. That should be left to professionals only.
- Electricity can cause damage, fires, burns and death. If you don't know about electricity, learn before doing.
- These are demonstrated for hobby work, low voltage - low amperage applications. NOT for mains voltages or currents or similar.
- Never use lead type solders where it will come in contact with food or drink or where it will come in regular contact with people.
- Lead is toxic. Take care to ensure that the byproducts / waste are contained and disposed of properly. Never hold solder in your mouth. Have proper ventilation.
- This is for hobby soldering only. Industrial users have more stringent requirements for industrial or large scale soldering operations.
- This is not all inclusive. If you don't know, get training before continuing.
SOLDERING VIDEOS & RELATED
Soldering Basics - Popular Connections
• Soldering Basics - Pop...
Soldering Tools - DIY Clamps
• Soldering Tools - Cla...
Soldering -Taping & Shrinkwrap
• Soldering -Taping & Sh...
Soldering Basics - For Cars, Experimenting, DIY'ers, Boats, Solar, ...
• Basic Soldering For Be...
Soldering - Water Resistant Connections, for Boats, Cars, RVs, Trailers, etc.
• Soldering - Water Resi...
DIY Third Hand For Soldering, Gluing, Hobby Work, etc.
• DIY Third Hand For Sol...
Soldering Closely Spaced Leads, Wires, Connections - Soldering Tip 2
• Soldering Tip - Extend...
Solding a Fine Wire to a Solar Cell
• Video
Salvaging Threaded Brass Inserts
• Threaded Brass Inserts...
Soldering Above or Below, Which is Right / Wrong
• Video
Common Soldering Mistakes
• Common Soldering Mista...

Пікірлер: 575

@tsbrownie 7 ай бұрын

SOLDERING VIDEOS: Soldering Basics - Popular Solder Connections - Done Right (4K) kzfaq.info/get/bejne/q8p-qJCov8fVenk.html Myth Busted: Soldering From Below kzfaq.info/get/bejne/nax3qbGjvtbXd5c.html Soldering Wires - Doing It Wrong, But Getting It Right (What is CRITICAL?)(4K) kzfaq.info/get/bejne/e9Bia5ef1928aGg.html Common Soldering Mistakes 1 kzfaq.info/get/bejne/o9xhp5CS1Lmof5s.html Soldering Mistakes 2 - Why Mechanical Connection Is Important kzfaq.info/get/bejne/f7aCjbKg0dKlco0.html Soldering Without A Soldering Iron kzfaq.info/get/bejne/mJuZnLh-prWrlas.html How To Solder - Electronics, Car Wiring, Boats, Solar, ... kzfaq.info/get/bejne/nbagnNZ3spyleZs.html Soldering - Water Resistant Joints for Boats, Cars, RVs, Trailers, etc. kzfaq.info/get/bejne/ocB_oLV2ntPXkXU.html

@duaneborgaes9223 2 ай бұрын

⚡🏁😌👍💯✨

@paulking8055 Жыл бұрын

7 years old and still helping people. Thanks very much, helped me a lot.

@tsbrownie Жыл бұрын

Glad to hear that, thanks.

@Tylerl128 7 жыл бұрын

I love KZfaq because of videos like this, where the pros go out of their way to show us, newbies how it's done, and the right way! The education side of KZfaq is my favorite part of KZfaq lol

@fr3dfixit945 4 жыл бұрын

Thank you! Getting ready to solder a bunch of wires and this is exactly what I needed before starting. Also, very grateful for the closed-captioning; can't always be in a listening-friendly environment, so being able to read the narration is awesome!

@tsbrownie 4 жыл бұрын

Glad I could help!

@fatpigbonzo 3 жыл бұрын

Subtitles also help us non-hearing folk too :)

@WelcomeToMyDream 5 жыл бұрын

Thanks for the video! It is so cool that after soldering for years, then not soldering for years, I can find such a good video in 2 minutes. Brushed up on the usual plus learned new stuff, can't beat it.

@boorandras9723 7 жыл бұрын

After some years of working with custom electronic projects I don't think that I'm a "noob" in soldering, but I could learn something new from this video. Thanks! :)

@Ottonic6 6 жыл бұрын

The tube butt splice was a great demonstration of how solder flows towards the heat source. Thanks!

@bergamotewilks 7 жыл бұрын

13:23 "this is a tremendously strong joint" This video is a goldmine for hip-hop samples

@thomashardin911 5 жыл бұрын

Hip-hop samples?

@Th13GhOsTs 5 жыл бұрын

@@samnassgood thinking batman, but obviously if you have a soldering iron then use it, solder won't corrode as bad as the copper 😂

@dustinwolfe9591 5 жыл бұрын

I got it. This comment is solid gold lol

@pascaljean2333 5 жыл бұрын

@@samnass but soldering was the whole point of the video no?

@bobmutchseo 5 жыл бұрын

lol forget the strong joint and that will shatter your reality

@suzannta2827 4 жыл бұрын

Thank you for not taking this video down that you made in 2015. I am going to solder my Swann Camera wire right now, this really helped me to get the courage to do it myself. Gracias from Mexico

@michaeldougfir9807 6 жыл бұрын

It's quite a long time since I first learned these things in school -- decades. Thank you for using your materials and for the demonstrations. Nice work!

@tsbrownie 6 жыл бұрын

Thank you. Very kind words. Comments like yours make it worthwhile doing.

@carlosjoelgarcia3200 Жыл бұрын

Your teaching style is superb and your camera close ups deliver the final touches. Thank you for sharing your skills, techniques and education with us noobs... Cheers.

@BlueRidgeMarine 8 жыл бұрын

This is why I like You-Tube. Been soldering for many years, yet I still learned something today, Nice camera work too. Thank you.

@tsbrownie 8 жыл бұрын

+BlueRidgeMarine Thank you for the good words.

@slepycitron 5 жыл бұрын

Practical, no fuss description. Thank you.

@joedejesus6363 7 жыл бұрын

Great Tutorial, I took up electronics in High School, this lesson brings back some techniques I've completely forgot. Thanks for a great video.

@tsbrownie 7 жыл бұрын

You are most welcome and thank you for the kind words.

@stewartloughrey2683 5 жыл бұрын

This is the best soldering video to watch and learn by. Thankyou very much mate.

@afrog2666 7 жыл бұрын

I`ve been soldering for around 20 years now and I still learned something here :) Thumbs up ;)

@HappySlappyFace 7 жыл бұрын

you are 47

@afrog2666 7 жыл бұрын

LoL, no.. You`re off by 11 years bud ;)

@HappySlappyFace 7 жыл бұрын

jan christian Frodahl damn

@afrog2666 7 жыл бұрын

Maybe I should change my profile pic :p

@HappySlappyFace 7 жыл бұрын

jan christian Frodahl xD

@rocks4real 5 жыл бұрын

To be honest; It this has cost me two hour lifetime to find a sensible video finally all my questions on the cable solder to a satisfactory result led! Many thanks for it!

@tsbrownie 5 жыл бұрын

I am glad you liked it. I started soldering when I was 6, I'm now 62. Taken courses along the way and done lots of soldering, so it has taken me a long time to learn!

@TM-pc1se 7 жыл бұрын

I was looking at basic soldering techniques and came across this video. This is excellent. Thanks so much for making this.

@tsbrownie 7 жыл бұрын

Thank you, glad you found it useful.

@JimiHendrix998 7 жыл бұрын

Good sense, nice, simply and clearly shown. Thank you. I wish we could prrsuade our buddies over the pond that "Solder" has an "L" in it ! ;)

@theultimatesauce 6 жыл бұрын

You know your stuff man. It was nice to see the types of connections you can solder with and the benefits of them.

@tsbrownie 6 жыл бұрын

Thank you.

@Tylerl128 7 жыл бұрын

thank you for posting this, it was a huge help!

@NNITRED 8 жыл бұрын

Staggering the joints is a great idea. Thanx mate.

@LifesAdventures555 8 жыл бұрын

I am the worst solderer in the world. You are truly a professional and make it look so easy. Great Video!! Thanks

@larrywebb8309 4 жыл бұрын

A lot of good knowledge , I would add that after you wrap one wire around another wire squeeze them together with vise grips or a simular clamping tool , then solder. Thanks for sharing the video

@michaelgovers8036 6 жыл бұрын

Man, it is so nice to see someone out there who knows how to solder, millions out there need to watch this ;)

@Kek5kopF 8 жыл бұрын

Some good tricks in this video, thanks.

@loscrimefighter1899 4 жыл бұрын

Thanks for taking the time to post this-turns out I didnt know nearly as much about soldering as I thought I did! 👍

@tsbrownie 4 жыл бұрын

Very welcome.

@laurencevillegarage 5 жыл бұрын

Great information, thanks for taking the time to make an easy to understand video. Learned some new things today!

@MaturePatriot 6 жыл бұрын

Thanks for the video. Helps alot. Just received a de-soldering tool, and proper flux. Using your information and proper tools should help.

@josephsmith6924 5 жыл бұрын

Thank you so much you have officially revived my interest in electronics.

@tsbrownie 5 жыл бұрын

Thank you for that.

@Clappinkyle 5 жыл бұрын

When I was working at a company producing power electronic components for the Japanese market we conducted a lot of tests on how to achieve the strongest joints when splicing wires together. We worked in a team for about a year and a half trying out different soldering and cold welding techniques to see which one should end up in production. But, in clinical testing including corrosion, water, conductivity and pull testing conclusively it turned out that a correctly crimped butt splice without solder was (although very contradictory to our preconception) the strongest joint for our application. I should point out that it took high quality components and a specific typ of hydraulic crimping tool that had to crimp the splices at an exact point on the butt splice to achieve this result (which works fine if you're, say, a robot who can repeat the exact operation a million times without error). Yet in the face of all that produced evidence, I still hold a firm belief in just soldering the damn thing... it just makes so much more sense!

@TheDarvec1 8 жыл бұрын

Got my first iron today and I've soldered everything except the cat ;) pre fixing the connection by wrapping it in fine wire is a win, really makes a neat job, cheers. Now for the 2 wobbly usb ports.....

@ScrewballMcAdams 7 жыл бұрын

Great tips! Thanks! Unfortunately, it never ceases to amaze me how someone, like you, goes to considerable tima, trouble and probably expense to setup, record, narrate, upload and ultimately share some valuable experience you've learned over the years only to have 1 or 2 so-called "experts" (legends in their own minds) who've done none of the above criticize your effort with hurtful commenrs. KZfaq is overrun with these trolls who get some thrill out of putting down other people. So please disregard the negativity from those assholes. This was a terrific, extremely helpful tutorial for me. Thanks again.

@TheRebuilt1 6 жыл бұрын

Great work and explanations. Really clean joints and never thought of wrapping wire around two bad/compromised joints. Nothing like age and wisdom that's in short supply these days . Thanks for posting.

@tsbrownie 6 жыл бұрын

Thank you!

@wmoy8507 4 жыл бұрын

Thanks. A lot of good info. For the last spice I personally would include two smaller heat shrink before I solder the two splices and then a bigger one over both splices. I just like the better insulation of double heat shrink.

@passiton3801 5 жыл бұрын

Amazing, I have never heard of or seen these techniques!

@phillamoore157 6 ай бұрын

Excellent video... Still trying to find an efficient way to solder 10awg wire (used on marine trolling motor) together, to where the solder soaks all the way through. Got the soldering iron set to 750, using the largest tip I can get for that iron, and generous with the flux. The one thing I DIDN'T do was flux all the strands before "pushing" them together, nor did I use a piece of wire to hold it all in place, which from some of the videos I've seen looks like it may help distribute the heat around the joint helping the solder soak better. These videos are very helpful! So, thank you for taking the time 👍

@tsbrownie 6 ай бұрын

Thank you for the kind words. 10 AWG should not be a big problem to solder. There are 2 "secrets" to soldering. 1) the work piece must be clean, bright fresh copper. Really clean. NO oxide. NO oils (from fingers, etc). 2) You must have adequate heat. Everything else is a "nice to have." And NEVER use acid flux on copper wiring. It will soak down into the insulation and keep eating away at the copper until it breaks. (I made this mistake, tried to clean out the flux over years, and still lost the battle. The stuff is cancerous.) So first, clean copper. Second, mechanically secure the connection. I have wrapped connections, but only when they are dodgy and I had no choice (emergecy boat wiring repair), not for heat dissipation. I have secured pig tail joints with a solderable crimp connector, but that was for mechanical strength. Third, apply flux if needed. Fourth, apply heat. Solder should melt at least 3 or 4 millimeters from the tip of the soldering iron (without having to touch the soldering iron). Finer solder costs more, but is easier to work with.

@phillamoore157 6 ай бұрын

@@tsbrownie WOW...what an amazing reply. Thank you so much. Do you by any chance have an e-mail address you're ok to share on here? I'd like to send you a couple pics of exactly what I'm working with. I find something (off of a sheer hunch) that I think will answer a lot of questions and want to see your thoughts on it. As I stated before it's 10awg wire, but all the "bare" wire, when stripped is silver. I'm wondering if that's why the solder wasn't soaking through. I was able to scrape off that silver coating to get what looked like bare copper, but can't imagine doing that with all that wire, especially given how easy the individual strands can be. I honestly have no idea if the flux is "acid" or not, I didn't see the word acid anywhere, I just know it's MG Chemicals "no clean", and I'm using 63/37 almost religiously, and I upped the heat to 800. I purchased the widest tips I could, as well. I'm going to test the motor over the next couple of days to see if what I did actually worked. If it does, then the only thing I need to do is clean up the solder job which looks like typical newbie, gloopy sh!t. BUT........if that's the only part I got wrong, then I'll consider it a success, given how involved the repair was in the first place. It will then just be a matter of re-soldering the joint till I get it "proper". *I can't thank you enough for such a great reply. Let me know on that e-mail, or if you have a business site you can directly me to outside of KZfaq. I'd like to stay in touch on this project till I'm satisfied it's done at a reasonable level.* Hope you had a very Merry Christmas, and if we don't talk, are able to bring in the New Year in a happy healthy, safe manner. 🙏

@tsbrownie 6 ай бұрын

@@phillamoore157 From the MG website "This tacky no-clean flux paste uses a mix of rosin, thickener, and high-grade synthetically refined resin." So it should be OK. If the solder is "gloopy", it sounds like it's not getting hot enough, but that's just a guess. Also, a big tip on the soldering iron/gun may be an issue: too much mass to heat up. I'm not a pro, just been doing it for 61 years and had some training. I can't accept emails, especially with attachments; if you saw the dozens of daily account hacks I'm subject to, you'd understand why. Thank you for the Merry Christmas and New Year's wishes, my best to you and yours also!

@christoffer1973 7 жыл бұрын

Thanks for a great video. great way to explain soldering.

@threecats407 7 жыл бұрын

In the hvac trades for years and do some electric too. Never saw that Western Union splice. Very cool!

@craxd1 8 жыл бұрын

I remember learning all of those splices, and our soldering lessons, in Vo-Ed, back in 1982-83. The field splice is a tricky one, as you have to tie a double loop knot in the wire. The Western Union is the one I use most, even today.

@dougg1075 4 жыл бұрын

craxd1 same here 86-87

@flatspider 11 ай бұрын

Great video … I actually learnt the names of some of the methods I’ve been using

@RobertL78 7 жыл бұрын

I have to solder connectors onto video coax cables used underwater that sometimes get water intrusion and corrode the shield or core. That trick for corroded with is a really good idea. I'll be using that one for sure. Thanks.

@tango-bravo 7 жыл бұрын

Thank you for this informative and helpful video. Enjoyed watching and def. learned somethings. I am in the process of wiring a CB to my car and this information will help a lot. I did wire a simple electric guitar once, P90 pickup and one volume one tone pot and I wish I knew these soldering tips at the time. Although the guitar functioned OK, the wiring cavity was not something I was in a hurry to show off!

@tchevrier 3 жыл бұрын

great video. I agree with pretty much everything you said. The only exception being the t-splice. I would never do it that way mainly because taping it or heat shrinking it becomes complicated. I would simply do a 2-1 one joint, slide a pice of heat shrink over all three wires and then a larger piece over the entire thing.

@maxmeier532 8 жыл бұрын

now this sure looks like a pro! great explanations!

@Promethium666 4 жыл бұрын

The last tip i found to be the best one, ive only recently started some soldering at home and i've spliced both wires at the same point like a right donut.

@waynepowell567 6 жыл бұрын

Excellent info. Thanks for the great video. Much appreciated.

@tsbrownie 6 жыл бұрын

Thank you, glad you liked it.

@Explorador65 7 жыл бұрын

Un video genial. Muchas gracias.

@capnchip 7 жыл бұрын

A varietion of the tube- with- hole method is to make a coil of smaller single strand wire around a drill bit that is the same size as the wire to be soldered and long enough to cover both bare wire ends, slip ends in each end of "wire tube" and solder. Makes a very nice connection. And can be used when little or no extra wire is available to twist together.

@simperfidelisfck 8 жыл бұрын

if you, like me, have tried to assemble cables with bad results, one must believe that this video be made for me.for some it is probably quite obvious how one should do. But for me it is an instructive video. Many thanks to you. that you bother to take the time to show what you can do.👍

@tsbrownie 8 жыл бұрын

+Marc Berg Thank you. Glad that it's of use to you.

@beatlesman369 4 жыл бұрын

That was very informative, thanks!

@bernardreynolds1 6 жыл бұрын

Thank you for a clear no nonsense or bad music, or sexy presentation of good information. Bernard

@tsbrownie 6 жыл бұрын

Thank you for noticing! ;)

@ComandanteJ 8 жыл бұрын

Very useful vid man!

@Lycantroph71 7 жыл бұрын

Great video! Sometimes it helps to drink a few shots before soldering thin wires, it helps with the shakeing. :-)

@creekbottomfinds 4 жыл бұрын

Very well done and helpful - Thanks

@ONE_GEN_X 5 жыл бұрын

Great video. Thanks for taking the time to do it

@tsbrownie 5 жыл бұрын

Thank you!

@johnnorris1615 5 жыл бұрын

thanks nice video..never had soldering lessons so good info

@shannons1886 8 жыл бұрын

Theses were all great!

@orly1415e 7 жыл бұрын

Thanks for sharing from Philippines

@russasaurous 4 жыл бұрын

Beautiful work

@Salsacola1 5 жыл бұрын

Excellent lecture

@shermanbeebe1 4 жыл бұрын

This is an excellent video. Thank you for the great information.

@tsbrownie 4 жыл бұрын

Glad it was helpful!

@yagoa 8 жыл бұрын

Love the mesh splice! I love using silicone tinned copper wire with a jet-lighter, takes some practice but really rewarding and by far the fastest way w/o a hot iron

@michaelskramii2245 5 жыл бұрын

Excellent tutorial - thank you for posting.

@tsbrownie 5 жыл бұрын

Thank you.

@michaelskramii2245 5 жыл бұрын

You are welcome - looking forward to more of your vids/tutorials in the future.

@j.r.thompson5950 4 жыл бұрын

Nicely done, very good how to solder properly. I know how yet your video explained some things that I was not doing correctly. Thank you.

@tsbrownie 4 жыл бұрын

Glad it helped

@joshjoy2535 6 жыл бұрын

Thanks mate for sharing! Good tips and advice.

@tsbrownie 6 жыл бұрын

Thank you.

@therugbee 5 жыл бұрын

Thanks....still learning!

@andersonogaranhaoitaliano6869 5 жыл бұрын

Obrigado pelos ensinamentos e conhecimento que nos transmitiu.

@tsbrownie 5 жыл бұрын

Thanks for teaching and knowledge gave us. You are welcome. Você é bem vindo!

@n74jw 4 жыл бұрын

Great video. Thanks!

@tsbrownie 4 жыл бұрын

Glad you liked it!

@butchroberts7224 7 жыл бұрын

Great job. 40 yrs of oxy/acetylene and Tig experience here and still struggle with solder with an iron. Stumbled across this looking for a clean way to insulate a branch on a wire harness with shrink wrap or expandable loom.

@tsbrownie 7 жыл бұрын

Thank you. Been soldering for 54 years now. ;)

@user-zh1pf8ly1j 5 жыл бұрын

I love these techniques ! I work on vintage radios and its nice to know some good soldering techniques (: awesome video!

@tsbrownie 5 жыл бұрын

Thank You!

@user-zh1pf8ly1j 5 жыл бұрын

@@tsbrownie Absolutely!

@JerryEricsson 8 жыл бұрын

Reminencent of the old Field Wireman course at Fort LeonardWood Mo back in 1970 but we did"t use solder as we were in the "field" and most of the time didn't have access to solder or irons. We made some very strong splices in the old field wire with it's multi construction of steel and copper wires. Interesting none-the less, and very usefull now that I am getting into the HAM scene.

@rmcustom9573 7 жыл бұрын

Thank you ! I too, have been soldering for 30+ years, mostly Automotive 12V wiring/harnesses/systems. Cars, Trucks & Harleys. I'm OCD when it comes to wiring connections & soldered joints ! Ha ! Ha ! Ha ! That's a good thing. I love it though. And I've learned a few nice tricks here as well ! Very good job tsbrownie, and thank you so much for taking your time & sharing your knowledge ! It will be put to very-good use on my end, fer sure !

@tsbrownie 7 жыл бұрын

Thanks for the comment and all the good words! Glad you found it useful.

@fernandoscrenci4874 5 жыл бұрын

Nice work!!!👍

@preparedneverscared8857 2 жыл бұрын

THANK YOU! apparently I have been doing this all wrong lol very informative 👍

@Scootersnmore 5 жыл бұрын

Fun soldering totally agree You work the same as me on solder joints.

@advanceddoorsandsecurity1245 5 жыл бұрын

awesome demo!!

@mrkrasker9609 7 жыл бұрын

Nice to see someone demonstrating good soldering practices on KZfaq. I have worked in TV and radio engineering and industrial electronics just about all my life and it drives me nuts to see how some people solder. I did a NASA soldering corse years ago and it stuck with me.

@tsbrownie 7 жыл бұрын

Well thank you. I was not lucky enough to learn from NASA. I learned at the end of a fist; I was my older brother's slave and got it right or got hit. ;(

@mrkrasker9609 7 жыл бұрын

I worked in a TV repair shop when i was 16 answering the phone and selling TVs and radios and keeping the store clean. I got beat with a broom just about every day if i did not sweep the floor correctly so I know what you are talking about learning at the end of a fist. Your brother sounds like my older brother who beat on me quite often.

@tsbrownie 7 жыл бұрын

Yes, the good thing is that what does not kill us makes us stronger.

@mrkrasker9609 7 жыл бұрын

first, when soldering you must make a good mechanical connection, he has done that. 2nd, I see no cold solder joint. 3rd He is talking mostly about making automotive and marine connections. Solder is not a glue as some You Tubers seem to think it is. I have seen countless examples of horrendous soldering tutorials on KZfaq this is not one of them. Might I suggest if you are such an authority on soldering practices that you post a video on the subject so we all can benefit from your soldering repertoire.

@tsbrownie 7 жыл бұрын

Thanks for your comment. I looked up that guy's youtube page, just a bunch of song lists. He's a troll. I run a clean establishment ;). I don't mind criticism, but I frown on people like him swearing, attacking others personally and trolling in general. I deleted his comment. If he comes back I will block him.

@ReTweetrix 8 жыл бұрын

Very Nice. Thanks for the post

@MadPilotOnBike 7 жыл бұрын

Nice video framed well nice and simply explained .

@tempesthoughton4441 4 жыл бұрын

Awesome tutorial. Thanks!

@tsbrownie 4 жыл бұрын

Thank you!

@polardeathdog5093 5 жыл бұрын

Tight and neat, good demonstration of the basics.

@Robert.K 7 жыл бұрын

Great, informative video. Thanks!

@tsbrownie 7 жыл бұрын

Thank you!

@marioexpropiacionpetronilo2753 4 жыл бұрын

Nice video! Very useful + interesting + great tone , perfect level, clear voice!!! Excellent!

@tsbrownie 4 жыл бұрын

Thank you kindly!

@gassanali8667 4 жыл бұрын

thanks for the great tips

@tsbrownie 4 жыл бұрын

Glad you found it useful.

@Thetrucky69 7 жыл бұрын

Excellent information.

@scorpionbradford 5 жыл бұрын

Thx u. This was like an online soldering class

@tsbrownie 5 жыл бұрын

You are very welcome.

@michaelovers688 5 жыл бұрын

Nice video thanks for the info

@humbertocares8385 7 жыл бұрын

Thank you tsbrownie!

@nadirsalim7419 8 жыл бұрын

Thanks for sharing.

@tsplittgerber 7 жыл бұрын

+tsbrownie Thank you for the great video. I just got my first soldering iron and am going to be doing some work wiring LED lights for my deck railing, and feel way more confident after watching your video. I of course will do a few practice solder connections first. Great camera work as well!!

@tsbrownie 7 жыл бұрын

Thank you. Be sure to use proper safety precautions. Wear eye protection. Pick up any splashed solder to keep away from kids and pets. Never work on connected wiring, etc. Have fun!

@johnhopkins6260 6 жыл бұрын

number 2: "basket weave" splice. Number 3, "NASA" splice (min. 3 turns @), Number 4: "butt" splice (typically crimped+ soldered)... modification of number 5: "military splice": form an "eye" in the strands of first wire (as with the eye of a needle) TIP: leave some insulation on the end of the second wire (to simplify "threading" the eye... wrap as above (removing remaining insulation end) wrap (collapsing "eye") solder and insulate.