How to Install Low Mount Fender Eliminator on 2019+ Kawasaki ZX-6R by TST Industries

Рет қаралды 10,197

Күн бұрын

Get your Low Mount Fender Eliminator here!: bit.ly/3QVXHi4
Take the look of your 2019+ Kawasaki ZX-6R to the next level with our sleekest fender eliminator yet. Our all-new TST Low Mount Fender Eliminator enables you to relocate your license plate to a lower location with no permanent modifications needed. Pair this with our Undertail Closeout and Universal License Plate Light and you will have arguably the cleanest set-up available on the market!
Make sure to subscribe here: bit.ly/1jq2ZrN
Follow us on Facebook here: on. 1nuTjlF
Follow us on Instagram here: / tstindustries
Follow us on Twitter here: / tstindustries

Пікірлер: 39

@slball123 7 ай бұрын

You are very good at narrating what you are doing and giving clear instructions. Well spoken dude

@robertcallahan760 8 ай бұрын

So clean!

@chazvelarde1055 4 ай бұрын

I did it pretty easy, I haven’t installed the taillight yet which I bought. But I have a check engine light on. I havent pulled codes but I do have two plug ins not connected due to the old plate. Any idea on how to fix?

@savageboy5533 11 күн бұрын

So I got the hyper pack for 2024 zx6r. Everything is going well but I’m pretty confused on the wiring for the license plate light.

@t3keen0ob 3 ай бұрын

Do you have an eta on when the low mount will be back in stock? I would rather wait to buy this than the standard mount. I subscribed on your website for notifications, thanks

@TSTindustries 3 ай бұрын

The laser cutting should be done this week. Then they go to powdercoat. After that assembly. I would say that if you can be patient for a week or two you will get your preferred choice -BR

@t3keen0ob 3 ай бұрын

@@TSTindustries nice, thanks for the update!!!

@aliankusmadi 8 ай бұрын

Nice

@rzrpwr 8 ай бұрын

Im wondering if the block off plate can be ordered with black screws

@TSTindustries 8 ай бұрын

Due to the lack of practicality of black hardware we do not supply pur kits with that option. We use stainless steel hardware .

@masonwooster7336 Ай бұрын

What did you do with the exhaust servo? Do you have a servo buddy or are you just rocking the engine light

@masonwooster7336 Ай бұрын

Scratch that I hear you say servo buddy I just had to listen a little longer

@Jade___ 4 ай бұрын

I have your fender eliminator and integrated tail light on my ninja 400, could i take those out and put them on a 24 zx6r?

@TSTindustries 4 ай бұрын

The tail light, yes, but not the fender eliminator. -TST

@Jade___ 4 ай бұрын

@@TSTindustries Thanks for the quick reply!

@TSTindustries 4 ай бұрын

@@Jade___ No problem!

@elricaguilar6693 3 ай бұрын

Is this mount compatible with turn signals like the R7 low mount ?

@TSTindustries 3 ай бұрын

Yes, you can mount a similar setup on this bracket. -BR

@cuzimaluzer777 8 ай бұрын

Any plans on doing some rear footpeg blanking plates?

@TSTindustries 8 ай бұрын

Nah. We have done those in the past and they rarely sell. It was a waste of effort and time

@zz-ic6dx 7 ай бұрын

What did you end up using to hide the holes where rear footpegs went?

@TSTindustries 7 ай бұрын

@@zz-ic6dx the rear pegs are still on this bike. We did not remove those

@codyjenkins6570 2 ай бұрын

Will the 19+ version work on a 2016?

@TSTindustries 2 ай бұрын

Unfortunately no. We do however offer a 2013-2018 specific tail light that you can find at our website TSTindustries.com . That part also has an instructional video to help you with installation.

@zz-ic6dx 7 ай бұрын

On the part when you take those 2 screws out and subframe droops, i cannot get them both to align no matter how much i push up on subframe, i got one bolt in but no luck on other one. I had the entire tail taken apart cause i was doing taillight and fender together, do i need to reassemble tail first?

@TSTindustries 7 ай бұрын

The subframe should be in place, and the subtray shifts within it. You just have to move around the subtray as you try to penetrate with the screw. Once concentric alignment is accomplished between subframe, subtray, and screw, it all just pops together.