Thanks man. Saved me a trip buying a part, it was the hazard button issue, jerked it around and they working again!
@cooperdog48268 жыл бұрын
God bless you brother. With out your video, I not sure I would have found it.
@bam69728 жыл бұрын
+Steve Hutson glad it helped.
@fubarlife77763 жыл бұрын
Can't figure out my 1982 Chevy Citation the flasher that works the turn signals and the hazards is in great shape the hazards work but the turn signals will not. I watched oodles of videos and tried to figure it out, put new bulbs in check the fuse, I only find one flasher it's not even where it's supposed to be according to the repair manual. I'll just continue to manually flash my blinkers forever 🤪 LMFAO
@TickledFunnyBone2 жыл бұрын
FYI to all a pinched trailer light wire between the spare wheel and the chassis has similar symptoms. Insulation of the wire rubs off and makes contact then pops the fuse for the turn signal + B/U when either passing reverse gear selection or going into reverse. This happened on a Blazer.
@FPapiSalOC8 жыл бұрын
I have a 97 Sonoma and there were only 2 T30 bolts to remove. Thanks to you I now have flashers again.
@bam69728 жыл бұрын
+Sal214OC great!
@therealjpoe232 жыл бұрын
Thanks again for the video. This has got to be the dumbest place to put the flashers. In the previous design it was easily accessible near the parking brake. Great job dealing with the people in the comments who asked questions that were answered in the video. You have the patience of a saint sir. You're to be commended for that as well. 🏆🏆🏆
@tmsek815510 жыл бұрын
short and sweet, mine just went out and i had them back working within the hour, good vid man
@juliouscanga37988 жыл бұрын
thank you so much, i replaced both and now turn lights and hazard lights work perfect.
@5Gumm2 жыл бұрын
saved me so much time g, you a legend
@knitwitch412675 жыл бұрын
lol my 4-way switch is held down with tape. Fuel pump and coil are on their own switch, can turn ignition off and take key out and the truck is still running... Keys also fall out if you make a left turn a little to hard. Ohh and that tape on the 4-way is because the button came out and it causes so many problems that im currently in the process of wiring the blinkers to a 3 way switch of their own and the 4-ways to their own as well.
@1miltond5 жыл бұрын
Thanks for you video the emergency flasher if get stuck will not let you turn signal work and the sign is you lights in the dash board will not come on thank you
@delwynholmes3567 жыл бұрын
the break light relay under the hood..when it's inpluged the high mount light gets brighter. plug it in and push on the brakes with it running and the idle drops till you let off the brake then it goes back to normal
@nestormejia26926 жыл бұрын
Thanks for the. Video I fix my car ready thanks 👌
@carlosa.larios93409 жыл бұрын
Thanks for the vid and the p/n man!
@bam69729 жыл бұрын
Carlos A. Larios Your Welcome. don't forget to like and subscribe.
@instrument_maintainer10 жыл бұрын
Thank you for posting the vid helped out a lot was really stumped on what the issue was
@dwightdunham51715 жыл бұрын
thanks bud! saved me alot of bad words looking for the relay.
@delwynholmes3567 жыл бұрын
brake lights, turn signals, and hazzards dont work but all the other lights do even the high mount brake light.when I push the brake the high mount comes on if I unplug the relay its gets brighter plug it back in n got the brakes the idle goes down
@delwynholmes3567 жыл бұрын
brake light relay..when inpluged the high mount gets brighter. plug it in and with it running hit the brake pedal and the idle will drop till you let off the brake
@samisolissolis65567 ай бұрын
Thanks for the video
@Nick-ie1ry9 жыл бұрын
Yeah was just about to give up , thanks for the video!
@bam69729 жыл бұрын
vick pollock your welcome.
@michaelcherry93353 жыл бұрын
Awesome video, fixed in 10min
@sneakyray91608 жыл бұрын
I did it! I fix my turn signal malfunction. Thank you for the info. You save me a lot of cash from the crook mechanics.
@ginomain22635 жыл бұрын
Sneaky Ray most mechanics are going to hell for sure!
@sneeks2537 жыл бұрын
thanks bro u save me a lot of time
@zachkintner46268 жыл бұрын
Thanks brother big Help!!! God bless
@bam69728 жыл бұрын
+Zach Kintner glad it helped ya. don't forget to like and subscribe.
@normanminer98887 жыл бұрын
Great job man!! It helped me out so much thank you again man do much!!!
@bam69727 жыл бұрын
not a problem. glad it helped. dont forget to like and subcribe ....
@crumega12637 жыл бұрын
thanks a lot ,you helped mii fix mii problem
@AlucardNosferatu5 жыл бұрын
Thank you so much it was the problem i was having
@bam69725 жыл бұрын
awesome. glad it helped.. dont forget to like and subscribe
@emo-_-nemo-69864 ай бұрын
So I did it it worked for a day but now when I flip the turn signals, it just turns on the hazard lights
@joshable1 Жыл бұрын
Thank you
@justme1958A26 жыл бұрын
I'm rebuilding a 96 Sonoma, trying to figure out WHAT the "box" above the flashers is. Mine is missing, Brake switch, every wire has been cut, the connector, that plugs in to switch,,,,, Not there each wire using a crimp connector. SMH
@delwynholmes3567 жыл бұрын
ok looking for short I hit the brake heard the relay making a funny noise..replaced it hit the brake and blew the fuse. so i inpluged the multiswitch but the brake high mount n driverdide brake light started working but not the oassingerside
@brandonmorrison237910 жыл бұрын
Thank you! Helped me out today lol
@bam697210 жыл бұрын
cool.
@Not_Sure_818 жыл бұрын
Hmmm.... Can I hope it's the same with the 94? My signals died very slowly. It wasn't a "suddenly stopped working" issue. They just slowly stopped working over time
@bam69728 жыл бұрын
could be. I would start there. there cheap.
@delwynholmes3567 жыл бұрын
ok thanks I'll check and let you know
@bam69727 жыл бұрын
Ok. i would like to know. i also got a 91 chevy 1500 pickup with the same problem. gotta check the wiring from the switch to the back by the frame rail to confirm if there is any wire shorting out. only getting 11volts to the ear bulbs but battery has over 12v. so gotta be shorting somewhere or bad ground. also the fuse for the tail lights is also getting really warm to the touch when on.
@asaamv7 жыл бұрын
i have a nissan march 2012 and iam having many electrical problems , right now fog light works and headlight works, front wiper but the electrical lock system not working and turn signal not working , and back wiper not working , any idea what do i have to change ? btw turn isgnal is flashing rapidly but no signal is on from the bulb
@delwynholmes3567 жыл бұрын
I tested for short by disconnecting the pos.cable. using a test light I clamped one side to the battery and touched the other to the cable and it lights up. so I made she everything was off and pull each fuse one at a time and the light never went off..does that mean theres a power to power short
@kennethking26873 жыл бұрын
94 has it underneath the wheel by the e brake
@therealjpoe232 жыл бұрын
Old design. 94 should still be the square body S-Series
@delwynholmes3567 жыл бұрын
hey I tested for a short by putting test light between terminals then pulled each fuse but the light stayed on...????
@mauriciodegante5422 жыл бұрын
Hola sabrás dónde van los relay la caja de fusibles dónde trae todos los relay por no se la encuentro Ami camioneta solo en cuentro los que están adentro del lado del piloto me ayudas para saber dónde se encuentran
@sneakyray91608 жыл бұрын
I have a 1990 Buick reatta with similar issue. Can it be the turn signal also? I thought the bulbs needed to be replaced but it still not working.
@bam69728 жыл бұрын
+Ray Lozada try changing the turn signal relay. 9/10 times its the relay
@carmencumbascaro35037 жыл бұрын
I got a 94 S10 blazer my right blinker won't flash bulb is new clicks fine bottom parking light doesn't work and left blinker works but flashes really quick bottom parking light doesn't work bulb also new...
@bam69727 жыл бұрын
with a test light verify that you have power and ground to the connectors. check the grounds that hook to the frame and body by the battery. may have to take battery and tray out to get to grounds.
@delwynholmes3567 жыл бұрын
when I push the brake the relay makes kinda like a hissing noise
@melfrench76938 жыл бұрын
swapped flashers to see if it would make blinkers work but it did not work. bought a new flasher and installed it and it still wont work. what should my next step be?
@bam69728 жыл бұрын
+Mel French it could be in the multifunction switch or the hazard switch.
@delwynholmes3567 жыл бұрын
at first after they went out I replaced the fuse hit the brakes and itbblew the fuse..I replaced the brake switch and it stopped but I would hear the relay clicking but no lights
@bam69727 жыл бұрын
check the wiring from the front driver side frame rail all the way back to the tail lights. there might be a short. also check the rear for a ground strap or just a normal ground to the frame. clean the ground back there and reinstall.
@delwynholmes3567 жыл бұрын
now when I push the brake I hear a noise coming from the relay
@Xmn328 жыл бұрын
98 1500 sierra, no running tail lights and turn signals??????
@bam69728 жыл бұрын
check all the body and frame grounds. especially the negative battery wires going to the frame and the body. they like to brake off in that area.
@chikita11878 жыл бұрын
BOUGTH A 96 SONOMA THE HAZARD SWITCH IS BROKEN OFF AND THE TURN SIGNALS DONT WORK COULD IT BE THE HAZARD SWITCH SHOULD I REPLACE THAT?
@bam69728 жыл бұрын
I would replace the flasher first as its less then 10 bucks. the hazard switch is part of a assembly and would cost a lot more to fix.
@opparigo34704 жыл бұрын
So my s10 turn signal work but hazard light doesn’t work just when I press the brake pedal any idea ?
@therealjpoe232 жыл бұрын
The brake lights override the hazards there's nothing wrong.
@thefoxx62627 жыл бұрын
What if mine blinks on the outside but on the inside no blinking or sound " any ideas 05 nissan maxima
@brandongreene43846 жыл бұрын
Would that cause the number one fuse and the number 16 fuse to pop together
@bam69726 жыл бұрын
no. you probably have a short to ground on the tailights. run the wires down the frame.
@davidarno79296 жыл бұрын
I have a 1999 GMC JIMMY that clicking of signal-stat won't stop clicking. Only when I apply brake will it stop clicking. Left and right signals both work, and hazards work, brake lights work. I just can't figure out why it keeps making clicking sound. I replaced signal-stat with new one, but still have problem. Has anyone else experienced this problem, and can give me an idea how to fix it ?
@bam69726 жыл бұрын
that is pretty weird. maby the turn signal switch has a short in it. try replacing that
@junioor_dpt54898 жыл бұрын
I have a 92 Silverado anybody know where the flashers are hiding at?
@blazerlover75386 жыл бұрын
What about a 1997 chevy blazer?
@bam69726 жыл бұрын
should be the same. i think in 98 they put the flasher behind the glove box
@leeisenberg7 жыл бұрын
What model & YEAR is this ???
@bam69727 жыл бұрын
1995 s10 blazer.
@brookehayes86678 жыл бұрын
omg thank you !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
@bam69728 жыл бұрын
+Brooke Hayes not a problem don't forget to like and subscribe. there will be more blazer videos soon.
@TrackVsATV9 жыл бұрын
Ok so I have a 1998 gmc Jimmy with the exact same problem but mine is a 98 and it's different it has no relays behind ash tray my only relay is behind glove compartment, I've checked all fuses and they are good, can anyone point me into the right direction is there another relay I should switch??
@bam69729 жыл бұрын
TrackVsATV im pretty sure that the 98 and up they put the flashers behind the glove box
@TrackVsATV9 жыл бұрын
bam6972 yes theres a flasher relay behind my glove box, but it only clicks when my hazardous lights are on i bought a new really and it still only clicks with emergency lights. i still can't figure out the problem
@bam69729 жыл бұрын
theres two different flashers. one for the hazards and one for the turn signals. there should be 2 flashers behind the glove box.
@TrackVsATV9 жыл бұрын
I've looked and looked and theres only one unless the owner before moved it, the only flasher there is says combination flasher.im going to have to take it to a mechanic
@bam69729 жыл бұрын
dam... let me know what happens
@chikita11878 жыл бұрын
changed the flasher and nothing ..it doesnt even click ///.. i guess im going to try to change the switch
@bam69728 жыл бұрын
that would be the next step. I would check the fuse first.
@nathanielvann53957 жыл бұрын
bam6972 what fues is for turn signal I have a 1997 jimmy GMC
@delwynholmes3567 жыл бұрын
brake light relay
@delwynholmes3567 жыл бұрын
brake light relay..
@reyyvasquez91169 жыл бұрын
Can this be the problem with my 95 blazer ? Blinkers Dont work! Sometimes right side blinker only works rare I have another issue with the low beam lights Dont work :/
@bam69729 жыл бұрын
REYNALDO VASQUEZ DJ NALDO listen to bottom right of dash. do you hear clicking when not working. if not replace this cheap part first. the low beams could be in the headlight switch. they go bad from time to time.
@delwynholmes3567 жыл бұрын
the break light relay under the hood..when it's inpluged the high mount light gets brighter. plug it in and push on the brakes with it running and the idle drops till you let off the brake then it goes back to normal
@delwynholmes3567 жыл бұрын
brake lights, turn signals, and hazzards dont work but all the other lights do even the high mount brake light.when I push the brake the high mount comes on if I unplug the relay its gets brighter plug it back in n got the brakes the idle goes down
@bam69727 жыл бұрын
check fuses and bulbs. what relay are you unplugging?
@delwynholmes3567 жыл бұрын
ok looking for short I hit the brake heard the relay making a funny noise..replaced it hit the brake and blew the fuse. so i inpluged the multiswitch but the brake high mount n driverdide brake light started working but not the oassingerside
@ibrahimomar23356 жыл бұрын
Thank you
@delwynholmes3567 жыл бұрын
when I push the brake the relay makes kinda like a hissing noise
@delwynholmes3567 жыл бұрын
now when I push the brake I hear a noise coming from the relay
@delwynholmes3567 жыл бұрын
the break light relay under the hood..when it's inpluged the high mount light gets brighter. plug it in and push on the brakes with it running and the idle drops till you let off the brake then it goes back to normal
@bam69727 жыл бұрын
do you hear a hissing or a whooosh sound when you push the brakes with it running?