Permanently seal exhaust leaks with this metallic putty

Рет қаралды 189,796

TutoBuild Eng

Жыл бұрын

How to simply and quickly seal exhaust leaks with a J-B Weld ExtremeHeat metallic paste

Пікірлер: 87

@user-jr2gt9nw8b 7 ай бұрын

Been using this on my header for 10 yrs. Hasn’t failed one time.

@socastee_5.097 5 ай бұрын

Do you think it’ll fix the holes in my manifold ?

@KollynJ 4 ай бұрын

@@socastee_5.097just a matter of for how long

@noobsc0uter1 Ай бұрын

@@socastee_5.097 it will smell a lot

@TempoDrift1480 Ай бұрын

You've been using it for 10 years or you used it 10 years ago? If you've been using it for 10 years then it sounds like it's not working.

@RandyGillespie-sr7ne 2 ай бұрын

Great product, sealed my gas fuel gauge on the tiller and lasted for 4yrs now.

@1955porsche 6 ай бұрын

this jb weld high heat works,, after u get this on 24 hrs add regular jb weld over the top n build up a thick area of jb weld

@matthewjbellamy1 9 ай бұрын

Nice tip with the vacuum

@dimitriberozny3729 9 ай бұрын

I have used Rutland Furnace cement with excellent results also.

@eshagh.ahmadi 7 ай бұрын

I liked your work, we have a great channel

@kevinlandaverde8524 5 ай бұрын

I used JB weld steel stick putty to patch my dads exhaust leak on his Catalitic Converter I was actually surprised It held up for over 3 years He recently sold that Ford As far as i know its still holding up

@djroofless1115 Ай бұрын

It works great for sealing! My garagist put this on and now I have no way of getting the stupid clamp loose because it seized the stupid bolts(it all in between the threads)😢

@jeffquach9030 2 ай бұрын

hey my aftermarket headers came in a 2 piece and it leaks on the joints, would this fix my header exhaust leak?

@LK-yz9cj 11 ай бұрын

this is the fix you use if you can't be bothered to spend more than 30 seconds on it before passing the vehicle off to be someone else's problem. he could have taken the clamp off and used exhaust tape but jb welding over the clamp will not last more than a few bounces down the road.

@david-m-creations799 11 ай бұрын

WE GOT WEIGHTS-N-FISH !👀🤪🎣

@andrewwmacfadyen6958 9 ай бұрын

Permanent new definition last 5 minutes

@safaatchannel4538 Жыл бұрын

Good product 👍

@tahep3906 4 ай бұрын

thanks for this very informative and helpful video

@adamr8628 Жыл бұрын

It sounds about 10% quieter on the "after"

@demonboston2943 Жыл бұрын

Louder after 😂

@Smokeybear_j.b Жыл бұрын

its a diesel he had the door open before so you could hear the leak more clearly, its just noisy because its a diesel

@rjl9707 Жыл бұрын

Peugeot diesel looks like; always noisier.

@grindupBaker 11 ай бұрын

@@demonboston2943 You can't hear the broken engine until the exhaust is fixed. Always fix your exhaust in order to hear your busted engine, is my advice.

@1marcelfilms Жыл бұрын

Great idea using a vacuum cleaner

@gladius_arbor Жыл бұрын

I don't think so

@noturscooper1350 Жыл бұрын

😂

@tugberksongar Жыл бұрын

👍

@ryanchau3786 Жыл бұрын

Good video. Wonder how long it last

@bobbouchee1452 10 ай бұрын

you can use sodium silicate furnace cement last about a year good enough for inspections etc

@Saint696Anger 8 ай бұрын

@@bobbouchee1452 Rutland furnace cement metal to metal?

@petedebo6906 2 ай бұрын

It still has exhaust leaks you can tell from the before and after it should be more quieter and that clamp is the wrong one the repair won't last long

@aaliahfuller1609 9 сағат бұрын

Yah I had this same problem I took it to the shop and now my car sound much better the jb don’t always work exactly and it made my car smell funny underneath then I added the wrap so that could be why I smelled something too same all the hassle I took it to the shop 💯

@-dazzy- Жыл бұрын

Do you have any videos on a fiat stilo?

@user-it4nu7im1v 5 ай бұрын

It amazes me how lazy you are There's a search bar and google if you need videos on specific models problems

@jeffroW0331 11 ай бұрын

Sounds better before the bandaid was applied

@izhanhanafi9348 Жыл бұрын

Can u use this on extractor?

@noturscooper1350 Жыл бұрын

Yeah brother it works on small extractor leaks this stuff is great

@Pajaropolas Жыл бұрын

Thanks!

@bhadhusha7022 11 ай бұрын

Price is costly better to buy used or new silencer...

@ravoony1916 Жыл бұрын

Hello collab?

@feisty_capture3944 6 ай бұрын

Good to put over fresh welds for reassurance

@ethan-py9he 5 ай бұрын

say theres a 2/8th inch diameter hole in my exhaust pipe. could i weld that bitch shut by filling the hole?

@paulwyland2926 Жыл бұрын

Can you put this around a leaking O2 sensor? I replaced mine and it’s leaking bad.

@HAL-dm1eh Жыл бұрын

From what I've read and seen on the internet (and it was a lot) JB Weld will melt right off anything on or before the catalytic converter, but it's just fine for something like this in the video. There is something that will work called furnace cement. Clean the area well and make sure it's got something to bite to.

@hamzaabdul4981 Жыл бұрын

Did you find a solution I have a leaking 02 sensor

@paulwyland2926 Жыл бұрын

@@hamzaabdul4981 yes, I forgot to torque the o2 sensor. Went to harbor freight and bought a torque wrench and torque it to 35 ft pounds and it doesn’t leak anymore.

@bobbouchee1452 10 ай бұрын

use furnace cement it will last about a year long enough for inspections and then some cheap to

@honorablewiz7447 Жыл бұрын

Ok now how do you get it off?

@bijdikh8516 Жыл бұрын

With a grinder or hack saw

@Mr_Chode Жыл бұрын

by then you're getting a new exhaust or at least a new muffler.

@mohsinrasul8450 3 ай бұрын

Did this... Lasted 2 weeks

@lackodhr.5303 Жыл бұрын

🤗👍👌

@petedebo6906 2 ай бұрын

Just have someone cut the ends off the headers and fab some exhaust pipe that fits inside the header and weld it no leaks until the header rots off

@paulbriggs3072 18 сағат бұрын

At the 23 second mark, this product says 1000 degrees Celsius or 538 Fahrenheit. WHAT??? 1000 degrees Celsius equals 1832 Fahrenheit. They literally switched them around!! 1000 Fahrenheit is 538 Celsius.

@Imwright720 11 ай бұрын

Actually it says 1000c and 538 f.

@echohunter66 9 ай бұрын

Those are just details man!

@Liberallez 5 ай бұрын

Blue Magic QuikSteel ThermoSteel is MUCH BETTER than JBWeld!! 2400 degrees F and it really holds!! I've sealed TWO exhaust manifold leaks...one Mountaineer... one Echo!!!

@knolez1546 4 ай бұрын

I'd just snap the muffler off at this point. The car will sound better too

@wilsoncortes1562 7 ай бұрын

Dont hear no different

@eyesopen6110 7 ай бұрын

Just weld it and be done.

@aaliahfuller1609 9 сағат бұрын

Exactly that’s what I did took it to the muffler shop got it done right

@zerozero1944 Жыл бұрын

sounds the same 😂

@captainnemo5379 5 ай бұрын

Don't do it. It's not that expensive to get fixed, go to a local small muffler shop.

@GMC.Sonoma.4.3 3 ай бұрын

Those shops rip people off big time.

@aaliahfuller1609 9 сағат бұрын

Exactly I tried this on a crack pipe i had because I had a leak and my car was sounding like a motorcycle so I took it to the shop after I used the JD stuff idk if it worked but it made a funny smell so definitely took it to the shop to get it done

@kadin420 9 ай бұрын

Chris fix did it first 😂

@saudiwave Жыл бұрын

Temporary job. Rust is there you need to change. Wasting money on adhesives brands . My opinion to replace the broken area.

@toneybatts1972 Жыл бұрын

ahhh no it cant....its crap

@danielbirch6219 Жыл бұрын

If it’s crap it’s because you haven’t done it right

@tommytomtomt Жыл бұрын

@@danielbirch6219 has nothing to do with not doing it right you can never do it right with putty or epoxy stop being a cheap Jew and get it done right at a muffler shop

@aaliahfuller1609 9 сағат бұрын

@@tommytomtomtyup i definitely took my ass to the shop mines sound the same but the noise was just lower 💯

@frankmelo2191 4 ай бұрын

Terrible advice and complete waste of money.

@tommytomtomt Жыл бұрын

It will last until you leave your driveway

@SaRaHSaLiX 8 ай бұрын

It's not paste at all . Its runny goo. Might be ok for tiny tiny holes but not a good product

@Saint696Anger 8 ай бұрын

I use muffler cement in a big 16oz tube for $10 bucks. I apply it maybe every oil change, it takes like 3 minutes to do but I need to actually change out my muffler 😂

@Vibrationofawesome 6 ай бұрын

There’s always the guy who shits on quick fixes in the comments cause he knows sooooo much about cars. lol it’s like their job or something

@bradydunham7892 5 ай бұрын

I used a similar JB Weld paste product plus the jb weld exhaust wrap on a pretty decent size exhaust leak on a ford e350 shuttle bus! It’s still holding hard as a rock even after a trip across Canada!!

@user-qd1oq5rz3m 5 ай бұрын

Every time I’ve used in weld it amazes me and have never repaired the stuff after