TV Will Not Turn On Troubleshooting Help - LED, LCD & Plasma TV Troubleshooting TV Will Not Power On

Рет қаралды 764,577

8 жыл бұрын

How to test for standby voltage to determine if the problem is the power supply or main board.
CLICK HERE for Replacement Parts: www.shopjimmy.com/tvs
In this video we will show troubleshooting steps that will work for a plasma TV, LCD TV & LED TV. Troubleshooting in this video will apply to a TV that will not power on. So if your TV will not turn on, either with the remote or by pushing the power button on it, try these troubleshooting steps.
In these troubleshooting steps, we will use a multimeter to check for certain voltages. In order to continue troubleshooting, be sure you have the proper training, experience, skills and equipment necessary to use a multimeter to check voltages in a TV.
Try all repairs and troubleshooting at your own risk.
Here we have an LED TV that will not turn on. The first thing that I can do is to check and see if there is a standby light in the front of the TV. Some TVs have the ability to show a standby light, while others do not. If I do see a standby light in the front of the TV, that shows that I do have some power going to the TV, but it will just not turn on.
We will continue troubleshooting.
I have removed the back cover off of the TV and I will use my meter to check the standby voltage on the power supply.
First identify the power supply in your TV. Then look for a cable that runs from the power supply to the main board.
Then you can look to see if the board has a legend on it, showing which pins show what voltages.
You will want to look for the one that shows the 5 volt standby. All boards are different, some will have a legend, some will not. Some will have the pin labeled and some won't. If your board does show what pin has 5 volt standby, then check that pin. If it does not show which one if the 5 volt standby, then you will want to check all of the pins on the cable, one at a time and look for one of them to show as 5 volts. As you can see, both pins 1 and 2 show our 5 volt standby. I will check pin 1. Be sure your TV is plugged in. After you check the pins, if you do have 5 volt standby, but your TV is not powering on, then I recommend replacing the main board.
If you do not have 5 volt standby, then you are not getting power from the power supply board. Assuming your outlet works, and the TV is plugged in correctly, I recommend replacing the power supply board.
A quick recap of our first step for troubleshooting the symptom of if your TV will not power on. If you check the 5 volt standby on the power supply, and your meter shows 5 volts, then your power supply is working, but the main board is not turning on the TV. So, I recommend replacing the main board. If you check for the 5 volt standby, and you do not receive 5 volts on your meter, then your TV is not receiving power and I recommend replacing the power supply.
This testing is a great place to start for troubleshooting these symptoms. In some rare cases, if you do have standby, and your TV will not power on, the problem could also be a component on the power supply board, however to start troubleshooting, it is recommended to replace the main board first.
We strive to learn and share new TV repair tips everyday. Subscribe to our KZfaq channel and grow with us, share our videos with your friends to help us spread the savings, and don't forget to hit that like button.
TV Repair Made Easy™
© 2015 ShopJimmy.com, LLC.

Пікірлер: 484

@doctortony1 5 жыл бұрын

Thank you so much for this educational video!!! By your multimeter test I needed a power supply board. Unfortunately the power supply board I needed wasn’t in stock on your website but I did find one on eBay and now my TV works again! No TV repairman costs at all since I was able to diagnose and fix myself. I’m in a debt of gratitude and will refer everyone possible to your website, videos, products...etc. Thanks!

@33flaboy 8 жыл бұрын

I have a Toshiba 40e210u1had this problem....after watching your video i figured out that I did have the 5v standby on the power supply so I replaced the main board as suggested. The Tv is now working again, thanks shop jimmy!

@jamesilic7542 7 жыл бұрын

Mate, you're a legend. Such a lovely voice!

@aaronharris8245 3 жыл бұрын

Sounds like guy with glasses from Harold Ramis from original Ghostbusters

@galaxyprime6543 7 жыл бұрын

Thank you for Your info!! Great Video

@stanstevenson4251 7 жыл бұрын

I spent a lot of time researching and studying everything I could with no luck!! I tested all transistors and caps with meters and out of circuit then replaced all the boards and still no luck one board was used and that my have been the problem or maybe something with something else it was a lighting strike so who knows. but thanks to all who helped!!

@Cat_shreya_catee_1 4 жыл бұрын

Wow. Dat was epic. Da best repair is to replace da faulty part. Almost like replacing a flat tyre. Congrats man.

@darren6202 2 жыл бұрын

Yes, except a flat tyre doesn't have a 5v standby (well I don't think it does)

@mulonru2965 Жыл бұрын

I am so glad found your channel

@hailyphuc1765 5 жыл бұрын

Thanks you very much!

@Au_n1 11 ай бұрын

Immensely helpful!

@georgewilliams7831 5 жыл бұрын

Thanks, That was helpful but in my country we do more repair them replacement

@karthigayanmunusamy7596 3 жыл бұрын

nice video and good explanation.

@davevallee7945 2 жыл бұрын

Hi Jim, thank you very much for your video. I have a Sony Bravia 60" kd-60x690e TV that is five years old today. It turned itself off, and will not turn back on. No lights, nothing. There was no surge. I removed the plug from the surge protector, and plugged it into the UPS, no change. I plugged it into the wall outlet, no change. I'm guessing a power supply board. When I watched your video, I could not tell where you grounded the other probe. Obviously, touching one probe to a connection, and leaving the other one dangling will not complete a circuit for electricity to flow. Where did you ground the other probe? Thanks.

@jenniferandshaunwilliamson6560 7 жыл бұрын

I bought the repair kit from you guys for the dps-162kp a power supply im wondering if you have a tutorial for testing and replacing each component in the kit.

@bikez5637 2 жыл бұрын

Hello Jimmy. Great video! I have a lg 55ln510, #310rmhr7b601 that will show picture for 30 sec and then the screen goes black. The standby light is on when tv is plugged in. I have checked the standby signal from pwr supply to main brd and get the listed value of 3.5V but I get a 0 for the 12v and the 24v pins. The pins for the wire going from pwr supply to led (+/- +/-) started at approx 13v and quickly dropped to 0 when tv plugged in but not turned on. No visible blown capacitors. Any suggestions would be appreciated. Thanks!

@Elfnetdesigns 8 жыл бұрын

Sylvania (Funai) 32 inch LCD that powers up and run for about an hour the shuts down, I recapped it, replaced power resistors that were open and the rectifier diodes and that brought it back to life to it's current state now. This set has a split power supply (AC mains / inverter board and system PSB.

@MrGeoffreoso 7 жыл бұрын

I have an LG 42LD690 TV. The power light shows in standby and goes to a wavering red light when on button is depressed. I have checked the power rails to the control board and they are ok. What outputs can one expect from the other outputs to the LED's? At the moment there is zilch. I have no picture.What and where do you think the problem area is? Grateful for any advice. The TV is only 5 years old.

@madisonventurini8455 7 жыл бұрын

Hello, what type of mutimeter are you using to check the power supply board?

@larryfray367 6 жыл бұрын

hey jimmy I heard if you have a emerson model LF501EM4 A RED BLINKING LIGHT CAN BE AIR SENSOR BOARD

@ianjones1110 8 жыл бұрын

Hi, I have a 32" Phillips flat screen T.V. - Model no. 32PFL5522D / 05 . All was fine until a few days ago when I went to turn it on via the remote and nothing happened. The standby light has never come back on when plugging into the power supply. Have tried all the usual tricks by checking the fuse in the plug, plugging T.V. into another socket in another room - no joy. I am about to take off the back of the T.V. and go through the steps as advised on your youtube commentary. It makes sense to do what you advise about checking the standby voltage etc. Just thought I would post this prior to starting the checking procedure in case anyone has any other types of advice before I start. Thanking you in anticipation Ian J.

@mohanp3684 5 жыл бұрын

Hello, I like your service and commitment to help / guide the community to repair the TV. I have a Sony TV - model KDL52XBR9. It has a blank screen - no video or audio or backlight. When I turn ON with Remote or Power button on the TV, just the Green Standby light comes on. If I disconnect and connect the wall plug, I hear some rely clicking and the backlight comes on for about 45 sec and backlight turns off by it self. Green standby light remains ON till I power OFF. Can you please help diagnose the issue? Thanks, Mohan

@kimant44ka 2 жыл бұрын

Hi Jim love the video troubleshooting ,I have a 40 inch pioneer plasma t.v it'll play for about a week than it goes out for about a week than it'll play again what could be the problem. Thank you

@vishalbhugra 5 жыл бұрын

Hello Jimmy, How to look for correct Voltage on Sony G1D board (XBR-65X900C). How voltage should I expect ?

@Berkner80 3 жыл бұрын

What if your getting 3V with PS-ON? I do not see 5V stand by but all other volts on PS going to main board check out.

@azn789456 4 жыл бұрын

hey, I have a power supply board with standby votlage. I shorted (using a tweezer) standby voltage to the power on pin to turn the tv on. then measured the unregulated 24v output and was only reading 1.4v. What could be the problem? I have a sony dps-162lp board

@remotewillie 6 жыл бұрын

Hi SJ as I was watching your video I ran a few test on my Hisense 50H7GB TV. I notice that when I press and hold down the power on the side of the TV the Hisense logo comes on and the TV picture comes on. The TV well stay on for about 2 minutes then it turns off. I have not opened it yet. Could this be a symptom of the power board?

@eskotheim633 5 жыл бұрын

Hi Shop Jimmy, Nice video, I have a LG, LED 55LW5700 tv, I checked all voltages all are goo except the "power on" voltage. It should be 24V and it is only 3.5V, All other voltages are good, does this mean my main board is bad?

@Labyrnthdom 10 ай бұрын

That's pretty good. However, I thought it was going to go into checking components and repairing the board instead of replacing it.

@pimpinsi 4 жыл бұрын

Thank You

@EricWebSurfer 9 ай бұрын

My Vizio LCD sometimes won’t power on. If I unplug and plug it back in, it will work for a while. Occasionally, it’ll turn off by itself while I watch, and I can usually just turn it back on. Also, if I haven’t used it for a few days, it sometimes won’t turn on. Unplug/replug seems to fix it as I described above. Power board failing?

@djchrisdabrain2649 6 жыл бұрын

Hi!! Thanks for those videos. They are helpful!! Well, I would appreciate if you can give me some advice about my problem.. I have my RCA LED TV wich after a thunderbolt won't turn on. I checked it up and found in the cold section, just after the optocoupler, one component tag as R431 (SOT23 encapsulated) exploited and close to it there was this component tag as SBR10100CTB (I think it's a rectifier), this one was in short circuit. I replaced them but still my tv won't turn on. I can see after replace those components I have 12V in cold section and dc volt but I don't see the 5v for the processor and the other part of the mainboard. Any clues? The mainboard part is TP.MS3393.PB855

@stuntcatproductions3714 3 жыл бұрын

I ordered a replacement power board for a TCL 55s401 (2 years old) because I had no backlights. Flashlight test confirmed there was a display. I installed the new board from ShopJimmy and I get no response at all; not even a standby light as I did with the old board. Thanks for any help.

@CS-ns1zu 5 жыл бұрын

I have a Sanyo model DP42D23 TV. It has a new P.S. board with all voltages good at the cable coming from the Main board. But it still doesn't come on .There is no standby light that is on. I went to the other end of the ribbon cable from the P.S. Board to the other rf/tuner/line out/in board and all the power and gnd's are good to that point. The board number on the board from the P.S. is NO: PCB J 0995 D1 W46/13. Other numbers on the board are Z7L 305A 49. Not sure if that helps. The power on/off button doesn't turn it on either. I do fine voltage across the power button when press. But still nothing happens from that point on. Do you think it's that board?

@vnosthas 6 жыл бұрын

Hello, I have a LG plasma tv model 50pj350 with sound but no image. I checked the power board and it is working, changed damaged mosfets on YSUS, caps read ok, so do resistors and diodes. Though the VY and VSC testing points shoud read -198V and 135V and I have no more than 60 volts on each. Any sugestion? I’ve tried to get the board diagram with no success. Thanks.

@user-fp3um4ef9s 4 жыл бұрын

Thank you. I am from Russia. And your English is very easy and I can understand it. It is great

@charlesgriggs1379 7 жыл бұрын

ty is on the picture comes on and off on and off just had the power supply replaced 3 days ago for same problem

@stanzie1778 3 жыл бұрын

I have a TCL 49S403. Do you know which pin is the standby or should I just check each pin?

@karthikeyanvengadaramani748 2 жыл бұрын

Hi Recently my LG 42 inch TV had backlight issue where video alone was not viable but that was too viable through flash light test. The service technician changed the back light LED after which the TV went to standby mode. Initially he replaced the main board still it was in standby. Then he changed the power supply board. Still same issue . He change TCON board even the issue persist. But finally when I asked him to change back all three to old board and when testing he was able to recieve supply to all boards. Which initially did not happen. Now with all old boards and backlight alone changed the TV still stays in stand by mode. I feel the technician is not having a sound knowledge on the issue and just like that he is saying the LED panel has to be changed. With your experience do you have any idea on this issue. Any small hint would be great full. Thank you.

@user-gk7pv9xz4s 2 жыл бұрын

Thanks for the great effort... I have a problem with the Samsung lcd-la32e420, and the problem is the following: When the power cable is connected to the power, the screen flashes and turns off immediately.. for the knowledge that the voltage measurements from the power board come out intact, especially 5 V.. Can you help me to solve this problem

@felixsantosmolina8872 Жыл бұрын

Hi, I have a Phhillips model- 24PFL3603/F7 the only thing that turns on is the Optical cable light, any idea what it could be.I changed the board and all the same. Would appreciate any help, thanks.

@victorsoliz4093 4 жыл бұрын

How could I test my power supply board My board is a APS-352 IS THERE ANY specific testing there in your line thanks

@pbgilley 8 жыл бұрын

Hi. I have a Panasonic viera plasma TH-42PZ80U TV that will not power on. The red light next to the on button blinks ten times. I am guessing based on research googling the 10 lights, it is the power supply board etx2mm702mf-n. Is that right? Will replacing this board do the trick? Can the board be purchased thru you guys? Thanks, Dick and Norma

@windysapphire 8 жыл бұрын

I have a Samsung 55" LED Smart TV that during a recent storm made a loud crack sound and shut down. I have verified that all items in the surge protector still work, but the stand by light and power to the tv does not. If I follow your videos, what kind of price might I be looking at if one of my boards needs to be replaced? Before I invest all the time and money I would like an idea if I should simply buy a new tv and if so, what brand would you recommend?

@dimitra.d792 2 жыл бұрын

hi sir you i want to ask about a samsung tv le37c630k1w this tv has only remote control no power key but i have test the remote is ok if standby voltage is ok so in your opinion the problem is the mainboard ? its not needed to check the other voltages of the power supply ? the red light of standby is permanently light and it seems to be permanently steady it doesnt blink when i give power on from the remote control

@1tonzz 6 жыл бұрын

on my samsung un46z7100wf, would these instructions be the same, I have a red blinking light, and is there a difference between the ld and the UN, thanks tony

@davevallee7945 2 жыл бұрын

Follow up - I left it unplugged over night, and it is now working. Yeah! Any thoughts on why it would have done that? Is a major failure imminent? Thanks.

@billyhardwick6396 8 жыл бұрын

Hello, I have a 12 month old vizio e48-c2 that will not power on (it began after a storm so, lightning is the primary suspect) I've removed the back panel and the components look like none I've seen on line. There is a small board at bottom center roughly 2x6 inches connected by a ribbon to a larger panel at 3 o'clock roughly 8x12 inches.. I can replace the the tv with a new one for $388. Can you tell me what the cost to repair might be? Is it possible that only a fuse is the culprit? Thank you. Kind regards, Billy Hardwick

@earthgal2000 8 жыл бұрын

Sucks that KZfaq is not allowing tech advice any more! Thanks for the video though.

@clems6989 5 жыл бұрын

What are you talking about ?

@BoHoGoJo 4 жыл бұрын

I have an Element ELEFW328 curb orphan I took in. It's Main & PS boards are combined into 1 disappointing failure.I plugged it in standby light came on, hit the pwr button but no picture. Replacement board was only $12. I put it in and same results. I measured voltage at the power switch this time. The board that it came with had 0v. The replacement board put out 6.6 at the power switch. I'm corn-fused. What do those disparate voltages signify? It the power switch bad? I dressed as Uncle Fester last Halloween. I was going to wear the same costume, but say that I'm Rudy Giuliani. Do you think I can pull it off?

@zafer5436 7 жыл бұрын

Hi Jimmy, I have LG 70inch full HD Led tv, unfortunately it does not power on, I showed it to a tv mechanic and He said that display panel is not faulty. Replacing a display panel is too expensive, is there any other way or any alternate method.

@andrew_koala2974 Жыл бұрын

What is a Multeye Meter ? And what has the eye have to do with it ?

@k.kastle3216 8 жыл бұрын

Sony Bravia 55" KDL-55HX800 model. I had a power surge which kept my tv from working properly. At first it would turn on and have a picture, then turn off. I got it to work for about 10 min. before it shut down permanently. The red LED is flashing 3 times in sequence. After trying to turn the tv on, the green led clicks off back to standby, red led, and changes to 7 blinks. This is repeated every time I unplug the direct power cord and re plug several min.'s later.. I will test the volts from supply to main as shown in your video, but do I have any other problem I should know or worry about before I attempt to test or replace anything?

@teresasproles9896 5 жыл бұрын

My 3yr old Vizio 50in went out so I bought a new board from you. Put it in and it fired right up, worked for a day, turned it off and couldn't get it to come back on. You were supposed to replace this board when one came in. I was told you get a lot of them and would notify me when one came in. No one ever notified me!! I'm still waiting.

@mcspillai2693 3 жыл бұрын

Hi, Is ther an over voltage protection on the power board?

@oscarh9546 6 жыл бұрын

do you need to ground your self before starting this process? If yes then how do you do that ? That might be helpful for your viewers. Thanks

@rhythmdevildrumfollower5987 4 жыл бұрын

If I bought a control board just recently to find out that it is not my Version after replacing the power board I still cannot get the TV to power on mine is a Samsung UN50KU6300FXZA DA01 version and I believe the board I installed was a DF08, is there a difference on versions for the control board that you cannot see that would make the tv still not power on, the circuitry looks identical? Any help would be great could it be the P jog switch? or do I just need to order the proper control board DA01 version

@kenhilson786 5 жыл бұрын

Would have been nice to see where you had the black lead of the multimeter

@Alien_O1 4 ай бұрын

Any metel part of the board as obviously thats ground.

@heatherflex 7 жыл бұрын

hi my tcl flat screen comes on then back off no picture just a white flash line...... advice please....

@jamie91433 6 жыл бұрын

Hey bud. I have a vizio, the power does not want to come on sometimes, but when I unplug it and plug it back in it turns on, the other day I had to replace the fuse in the psb. I am wondering what is causing the fuse to blow and what is causing the the power cycle issue

@nigelsimeon8647 7 жыл бұрын

Hi, tv has standby light but goes off as soon as picture tube wanna turn on, what can I check for?

@cairarocks4111 5 жыл бұрын

Hi there looking for some advice I have hitach tv that there is standby light but it flickers blue to red etc pressing the button the tv doesn't come on also my board doesn't show what pin is the standby volt. Do you have an email as I have photo of my board to see if you can help me

@timfuzer7393 6 жыл бұрын

Hey Jimmy I have a plasma tv to fix. Lg plasma 50pt350ud is the model. The tv comes on and screen lights but no picture. It will not allow channel change or input change those buttons are unresponsive when pushed. It has no picture or sound.

@ryanbooth9620 5 жыл бұрын

I have a problem where my old board gives me power to light up led on front but he board I bought from shop jimmy doesn’t. Any thoughts? Am I missing something? Could I have gotten a bad board from you guys?

@navybrat7173 8 жыл бұрын

I have a Dynex TV Model Number DX-40L261A12. The TV will power on after unplugging then plugging back in. It takes multiple times to do this. I do have the red indicator light that stays lit. Once the TV is on the picture is still excellent and everything works. I did try another power chord and that is not the issue. What do you think it could be?

@stevenbaker7256 7 жыл бұрын

have a sony kdl-60w630b it has a solid red standby not blinking and will not turn on. any sugestions

@kennye9727 8 жыл бұрын

I have a lg plasma 60pm6700-ub. I believe it was stuck by lighting as the surge protector shows it is no longer protecting. Standby light will blink, when I try to turn on screen shows a faint gray color but never shows picture or sound and then appears to turn off. 5v standby pin (what I believe is the pin) one shows around 4 volts(first time using meter). Any help appreciated

@paulkirch4028 8 жыл бұрын

I have a VIZIO L37HDTV10A. The power light is yellow on the front when it is off and turns on to green when I hit the power button but the screen does not light up. The problem started a week ago when it took longer for the screen to appear and now it will not appear at all. Haven't done anything yet to the set but will take the back off soon. any hints. The video I watched here advised to check the pins for power if it is labeled. Any further help?

@ronfiggins4996 Жыл бұрын

I have Sharp 58Q733Ou and have replaced all 5 backlight strips. Using LED tester at wiring harness, will not light LED strips/ showing open circuit. Have replaced wiring harness but still shows open. All 5 strips light when tested individually. Not sure what is causing open circuit. Thanks

@jimtrimm4473 6 жыл бұрын

My Sharp Aquos picture went away when I changed channels. I had sound but no picture. I turned it off and on but then had nothing even after unplugging it. On the front of the TV I have the OPC and Power lights flash together with the Power light flashing two more times before the sequence repeats. I have tried several of the suggestions to push buttons to reset with no luck. Inside on the Mainboard there is a light near number 20 and TP2003 label that flashes constantly until the TV cuts itself off. I exchanged the power board but no change. Should I replace the Mainboard? If that gives me a picture, will I need to do a reset procedure?

@dmoneybohnet1983 7 жыл бұрын

Im looking for Proscan 117736 (RSAG7.820.1185) Power Supply Unit. I think it may only be a fuse can I get one of those while waiting for the power supply unit to get in stock?

@pollydor07 5 жыл бұрын

Thanks

@bambam1095 7 жыл бұрын

Jim I have a lg55- ug tv and it turned off on me because my outlets burned out with the tv was plugged in too now the tv don't turn on but I do see a red light when I plug it in . Idk with one to change first ? Pleas help

@AZTEC_ARTS2023 5 жыл бұрын

Where do you put the BLACK multimeter tip ?? (Ground) while you touch the pins with the red one ?

@winstonaarons700 8 жыл бұрын

I am a repair tech with 25 years experience in the repair field with a big communication company in Jamaica.The problem I have is with a Samsung tv model number UN32F43AFXZP the fault is it will not power up when the power button is pressed. The power light come on then flash 5 times the off. I have taken out the power board inspected it the caps seem good then I checked all of them they are all good. I power up the board by it self all all voltages are present. Can you enlighten me as to what might be the fault and if it is the main board or power board where can I source these boards appreciated in advance

@brettnelson13 5 жыл бұрын

I see your red + cable going to the pin on the power supply board. Where do i touch my black lead from my meter? Thank You !

@erumdiana 4 жыл бұрын

Put black lead to the ground anywhere to the tv metal body

@juniorplacide1241 8 жыл бұрын

hi jimmy. i have a sony aps-319 . what happen is when turn it on, it just shows sony on the screen and dark back without any image' what do you think that might be the problem?

@carlunger3035 8 жыл бұрын

I have a rca mod #led42c45rqd ser # 2505-ld42c45d100735. The picture would shut off but the sound still worked shut it down and restart and it would work again. Now it starts flashes on for a couple of seconds and turns off. I looked at all the capaciitors and did not see any that looked bad. I only see two boards power supply and main boards. Where would the T-con board be located?

@mrfoamiercplanes6859 2 жыл бұрын

I have a SamSung 59" D6900 Series 6 3D Full HD Plasma TV that was manufactured in 2011 that will turn itself on and off every few seconds and is stuck on PC input this first happened over a year ago when I was switching the input source from one source to another too quickly and I was reluctant to dispose of it because when it is on the picture is near perfect ! Very annoying problem if you have any suggestions what part I might need to replace (if I can find one for such an old TV) that would be very helpful thank you.

@victoracevedo4318 8 жыл бұрын

Hola no se mucho ingles pero..Necesito ayuda con la reparacion de mi led tv, tiene el problema que muestras en el video pero la placa es de esa familia china TP.VST59.P83 y estas vienen fabricadas con la fuente y todo en una sola placa, espero me entiendas.

@jamesherman6492 6 жыл бұрын

My 50" Panasonic TV TC-P50U50 when plugged in the red led light is off. Pushing the power button on the remote will turn on the red led light but not screen or sound. The red led "does not blink". The remote will not shut down the TV or do anything, have to unplug to power down. I tested the power supply board (MPF6913B 1Z) at the output pins and no 5v standby voltage. Which is odd since I have the standby red led. So would it be the power supply board or would something be happening to my main board?

@Darthyonny 8 жыл бұрын

Hi there. Please HELP! Our TV is on the fritz and we need some advice before we can move forward! Our TV is a Sylvania (now Funai), model number LC407SS. The TV was turned off and then back on again and from that point, it was dreaded history. Long story, short, the TV will not power on at all, no stand by light, the TV makes sort of a high pitched buzzing noise. No back lights are present, either. We went through a couple of your videos about troubleshooting, but are at a loss on which part to go with first. Your advice would be greatly appreciated. Cheers!

@jimbrooks2668 6 жыл бұрын

Is the power board LF501EM4F (A3AUGUH) interchangeable with the power board LF501EM4F (A3AU0MPW)? Thanks!

@angelramos3827 6 жыл бұрын

Jimmy I have a Polaroid TLAC-02255 and I conect the power cable and the standby light torn on red , When I turn on the tv the red light changes to blue and tries to start the screen apears the logo polaroid after a few seconds turn of and change again to red. I check the power supply and have 2.9 volts when turn on changes to 5volts and after few seconds changes again to 2.9volts

@jasonaspro7409 3 жыл бұрын

I have 5v on SB pin of PS but 11.6v where I should be getting 12v and 19v where I should be getting 24v...Any suggestions? PS or mainboard replacement? Thanks.

@augustinechinnappanmuthria7042 4 жыл бұрын

Super 💗

@stanstevenson4251 7 жыл бұрын

OK I replaced the power supply and the main board and still will not power on???? I have 3.3 standby volts on the ps. Philips 47pfl5704D/F7 any suggestions now?? Please and Thank you

@stanstevenson4251 7 жыл бұрын

no, just gave up i know it sounds bad but i learned what i wanted to know

@freedomunrestricted 6 жыл бұрын

Suggestions on where to start if the tv turns on for a few seconds then powers itself off? When it turns on get alot of white static on the bottom 1/4 of the screen. Have looked over all the boards with a magnifying glass. Do not see anything blown or damaged.

@mikehellraiser143 6 жыл бұрын

If your not getting power or standby light on Samsung LED try unplugging the LED cord that runs from the yellow power board through the back of the silver panel and power the TV on. If your standby light comes back on its a burnt out LED strip. Saves a lot of time and money avoiding jacking around with boards if the LED is bad.

@MultiJoeMoma 4 жыл бұрын

What if I have no red standby light but have 5 volts on one of the terminals out to the main board? Bad main board or could the power switch section fail; the area where the red light is and the remote sensor.

@rogerattanas3626 8 жыл бұрын

I have a Toshiba 40RV525U that will not turn on after sitting for 1/2 hour or more - or is cool. To turn it back on after it is cooled, you have to turn it on an off approximately 11 times. Once on, it functions perfectly. What's going on?

@OtakuHeaven 7 жыл бұрын

I don't know if you are still active, but I have a vizio smart tv. I got it from my grandfather, and the IR sensor wasn't working, so I took it apart to find the issue, and when I did, I found that the IR sensor clip broke. So I fixed it, and powered the TV on to test it, I turned it off with the remote now, everything seems fine. Now, when I place the IR sensor back in it's spot, I test again to make sure before I close it up. Now the TV won't power on. Nothing looks blown, no dark spots, and all the cords and wires are plugged in all the way, any ideas?

@hexdude24 4 жыл бұрын

I have standby 5 volts. I don't see any standby LED lit except LED on Network Port on Main. Power button does nothing. Main board is expensive. Is there any way to jumper or "trick" power supply to fire up the 12v side for further testing?

@augustvarwig2058 5 жыл бұрын

Are you putting the negative meter lead to ground?

@andystevenson8370 5 жыл бұрын

i have a 32"sanyo replaced all 3 boards [ from shop jimmy] and the tv does the same thing. comes on long enough to read the input then goes black. any ideas?

@lauributt8023 5 жыл бұрын

My standby lights comes on and standby voltage is 5v, so does that mean it's the main board? I founds this 55inch screen on the curb.

@mohamedsalahnekhoul9117 4 жыл бұрын

Turn On the TV using remote control and Measure the different output voltages from the Power PCB if okay, then the Main PCB is not working properly(not sending Power ON signal to Power PCB).

@nelsonduque6569 7 жыл бұрын

Hi Jimmy. I have a Panasonic TC-19LX50. The stand by light turns in green then makes seven red blinking then seven red blinking over and over and never turns on the screen. Pls advise.

@AnthonyMitchelltrueblue33 7 жыл бұрын

I have a question, I bought a main board from you guys, it worked for a day. What's happening is when I plug the TV in, it turn on and when I turn it off! It comes right back on! I disconnected the Power on buttons and it still turn on. What could that be, the power board or the main board?

@jackancoke6236 7 жыл бұрын

I have a MITSUBISHI MODEL "WD-60638". When I turn the TV on nothing happens nor does the indication light come on. I tested the 5V test area on the power board and got a varying 1-2V reading. What would you suggest i look at next. Thank you for your time.

@jenniferwilliams9422 8 жыл бұрын

I have a Vizio VP422HDTV10A that doesn't turn on. The standby light comes on and in complete darkness the screen turns on but only for a few seconds, then it goes black again. The standby light stays an amber color. I don't have a volt meter ( I'm not sure what it's called lol ) so I'm unable to check the 5 volt you are referring to in this video. I would appreciate any help or advice. Thank you!

@user-il4br8du1s 4 жыл бұрын

Replaced all boards on roku TV 49l621u and turns on then off right away.power board shows all good voltages.the digital audio light stays on ,on the main board.Could it be a bad inverter?stand by blinks then goes out.

@cracksm3 4 жыл бұрын

What if it’s testing at 3.5 with a cheap multimeter ? All pins are testing lower than they’re actually marked. This is the first time I’ve used this multi meter. Should i still go ahead and replace the main board? It’s an LG TV and there is a board in the middle of the power board and main board. Edit: I’m fairly sure it’s the meter that’s not accurate. Everything is testing 20-25% lower than what is listed.