We are finishing Carlos truck and adding the two piece drive shaft a very simple setup
Пікірлер: 30
@jesusreal77Ай бұрын
yo bro so what all do i need to make a nbs extended cab fit on a nnbs crew cab , i know i need the 2pc driveshaft of extended cab but what u joints and yoke ?
@Angel-hp7oz2 ай бұрын
whats the nut size for the carrier bearing?
@ismaelsalazaracosta30024 ай бұрын
Wouldn’t the crossmember need to have a little hump in the middle to raise the drive shaft where the bolts go into the cross member? I’m about to make one like yours but all the cross members I’ve seen have a 5-6” hump in the middle to raise the drive shaft
@user-bg7yh5fo3j2 жыл бұрын
What I joint did you use? I’m having problems with my swap rn because the new u joint I put in is too big for the yoke on the rear end
@GBP_Vlogs2 жыл бұрын
you probably used a 1310 to 1350 u joint ? you need to get a 1310 u joint on all 4 sides
@tonyanthony78462 жыл бұрын
need some oil on that drill bit
@eduardojimenez21793 жыл бұрын
Would you happen to have sizes on anything that was fabricated need to get this done for my crew cab
@leandroaguilar16993 жыл бұрын
Hey I have a question on the driveshaft, I got the same truck same year and everything but the extended cab 2 piece fits the crew cabs?
@GBP_Vlogs3 жыл бұрын
Yes they do making the crossmember the hardest part
@littlegallo75982 жыл бұрын
Would this work for a lowered 2001 Silverado for a 8 inch drop I’m having vibrating issues nd the drive shaft straps broke on me before
@GBP_Vlogs2 жыл бұрын
Yes does it have a two piece drive shaft already? Or a single
@ferny_4.83 жыл бұрын
You think you can make me one and install it I’m in az ?
@JoseNavarro-qo8jp7 ай бұрын
Do you know the measurement of that crossmember?
@GBP_Vlogs7 ай бұрын
i never took them down sorry
@HL-kb1ex3 жыл бұрын
I have a 09 sierra crewcab, would those fit for the older years
@GBP_Vlogs3 жыл бұрын
Has to be from 99 to 07 extended cab Silverado or Sierra. To fit. My is a 2007 nnbs and has one out of a 2003 Silverado extended cab truck
@oscarrodriguez20373 жыл бұрын
It’s that drive shaft are you using will work on a 08 Silverado with out do any mods to the shaft
@GBP_Vlogs3 жыл бұрын
Yes I have the same one on my 07 nnbs
@oscarrodriguez20373 жыл бұрын
Thanks for that help ,I blow my drive shaft this weekend
@christopherbalderas4367 Жыл бұрын
Si tienes las medidas del plato
@jonathansandoval4413 Жыл бұрын
Where you get the steel tubing at ?
@GBP_Vlogs Жыл бұрын
you can order it or if you have a local metal company just ask about square tubing
@jonathansandoval4413 Жыл бұрын
@@GBP_Vlogs if you can make a video that’d be cool ! Thank you bro
@josuebravo92583 жыл бұрын
Do you have a template for the cross member
@GBP_Vlogs3 жыл бұрын
No I never made one
@JuanAlvarez-ii8ce3 жыл бұрын
Would a 99-06 2 piece shaft fit my 2008 5.3 Crewcab if I got a 4L80e Swapped into it?