Two Trees CNC TTC 450 - Max Speed Test

Two Trees CNC TTC 450 - Max Speed Test - 3D Engraving of Owl

Рет қаралды 10,635

Күн бұрын

Checking the maximum speed... Inspired by Harry Potter's owl Hedwig...
TTC-450 Photo Album: photos.app.goo.gl/AtB5M3U7ixF...
00:00 Intro
00:09 Original TTC 450 Specification
00:20 Home Position and preparations
05:44 Roughing
13:46 Connection loss
29:28 Tool change
33:28 Finishing
01:18:00 Ending
01:18:37 The Result
01:18:57 Thanks for Watching
#cnc #woodworking #diy

Пікірлер: 19

@SoaringExperience 7 ай бұрын

For the 1.5kW Spindle motor you need a vfd inverter, right? Like an elctric speed controller on RC planes or cars. Which one do you use? Great channel BTW. AND really nice how fast you are answering :D

@VAZHURERACING 7 ай бұрын

yep. Spindle + Inverter. I bought the kit on Aliexpress. (check 110/220v for your country) Something like this aliexpress.ru/item/1005004428206105.html?sku_id=12000029151476565&spm=a2g2w.stores.search_results.7.270a66ddVeWmi3. But cylindrical one maybe even better to adjust height (clearance) on the fly...

@amritsharma5 8 ай бұрын

How you upgrade this

@waltw918 4 ай бұрын

Does the air assist come with this unit?

@VAZHURERACING 4 ай бұрын

nope, I use cheap air compressor for ponds 😅

@BadTwin25 8 ай бұрын

1,5w ore 2,2w Spindel? Edit: I see 1,5w. I want update my 450 with a 1.5w Spindel too..it is easy to do?

@VAZHURERACING 8 ай бұрын

Its heavier than 775, so you need to modify z axis module. Album photos.app.goo.gl/AtB5M3U7ixFz48iRA

@m_us_i_c 2 ай бұрын

В какой программе отрисовываете?

@VAZHURERACING 2 ай бұрын

В разных, у меня есть свой редактор. Собирал в ArtCam. А так есть еще Vectric Aspire. Сова была сгенерирована AI, потом переведена в карту высот вручную.

@incubatork 3 ай бұрын

I'm no expert and have No idea which software you used for tool paths but next time try adding an imaginary vector border to say 10mm outside of the main design, that way your finishing tool will wear down less not taking off all the excess material that could have been done in the roughing stage, a lot quicker too. Depending on the software you set a eg 10mm border and rough pass outside and finish pass inside this line, most CAM software have it inbuilt in like Carveco Maker. Turned out nice and well recuperated after losing USB connection.

@VAZHURERACING 3 ай бұрын

Thank you! You are right, but this is just an experiment, so there is no rush. ✌

@amritsharma5 8 ай бұрын

Please make a seperate video

@VAZHURERACING 8 ай бұрын

Thx, I'll think about this ✌

@mccrain1514 8 ай бұрын

Max speed test with an heavily modified machine like this makes no sense...

@VAZHURERACING 8 ай бұрын

Comments like this makes no sense... ❤

@incubatork 3 ай бұрын

A Max speed test is always good to do, that way you know your limits before you start to save heartbreak at a later date, like 5 hours into a job and a motor skips a few steps because you were pushing things outside of its limits

@MrMatador1955 Ай бұрын

I purchased recently a two trees ttc 450, im getting a error code ¨ hard limit ok¨´ on the screen, i tried to disconnet power several times n still the same error on the screen, is there something i can do?

@VAZHURERACING Ай бұрын

Disconnect temporary end switches to check. Maybe it's sitting on it

@MrMatador1955 Ай бұрын

@@VAZHURERACING thanks!