Types of loads in FEA Structural Analysis

No video

Types of loads in FEA Structural Analysis

Рет қаралды 20,549

6 жыл бұрын

This video explains the introduction to loading condition, possible loads in structural analysis & its application with examples. It also briefs the load application in ansys.
*************************************************
Morning Sun by Nicolai Heidlas Music @nicolai-heidlas
Creative Commons - Attribution 3.0 Unported- CC BY 3.0
creativecommons.org/licenses/b...
a href="www.hooksounds.com", Music by HookSounds
*********************************************
Please Subscribe to Our Channel: #GraspEngineering
Similar Videos:
1. Introduction to practical Finite element analysis
• Practical Introduction...
2. Structural FEA Analysis of Topside Module using ASNYS Workbench
• Structural Analysis of...
3. Buckling Analysis of Pipe using ASNYS
kzfaq.info?o=U&vide...
4. Submodeling Analysis using ASNYS Workbench
kzfaq.info?o=U&vide...
5. Midsurface, Surface and weld creation using ANSYS Design Modular for Base Frame
• Midsurface, Surface an...
6. Vertical Pressure Vessel Modeling Using ANSYS Design Modular
• Vertical Pressure Vess...
7. 1D beam topside module Structure Modeling using ANSYS workbench Design Modular
• 1D beam topside module...
8. FEA Static Analysis of Pressurized Stop valve using ANSYS Workbench
• ANSYS Tutorials. FEA S...
9. Nozzle Shell Junction FEA Analysis USING ANSYS
• Nozzle Shell Junction ...
10. Bolted Flange Gasket FEA Analysis Usign ANSYS Workbench
• Bolted Flange Gasket F...
11. Hydrostatic Pressure application in ANSYS
• Hydrostatic Pressure A...
12. Vertical Pressure Vessel Hydrostatic test analysis as per ASME Guidelines using ANSYS Workbench
• Pressure Vessel Hydros...
13. Lifting Analysis of Horizontal pressure vessel using two lifting lugs in ANSYS, Part-1
• Lifting Analysis of Ho...
14. Lifting Analysis of Horizontal pressure vessel using four lifting lugs in ANSYS, Part-2
• Lifting Analysis of Ho...
15. Introduction to Rotordynamic Analysis Using ANSYS, PART-1
• Introduction to Rotord...
16. Rotordynamic Modal Analysis of Impeller in ANSYS PART- • Rotordynamic Modal Ana...
17. Ellipsoid Head with Eccentric Nozzle & Reinforcing Pad Modelling Using Ansys Design Modular
• Ellipsoid Head with Ec...
18. Hoop & Radial Stress correlation of pressure vessel with FEA using ANSYS
• Hoop & Radial Stress c...
19. Forklifting FEA Analysis of Base Frame using ANSYS
• Forklifting FEA Analys...

Пікірлер: 51

@jagannathareddy4287 3 жыл бұрын

Thanks and very useful.Appreciate your effort

@graspengineering9249 3 жыл бұрын

Glad it was helpful!

@nidakhan7873 6 жыл бұрын

very good video. Thank you.

@graspengineering9249 6 жыл бұрын

Welcome!

@muhJaw 3 жыл бұрын

Great work, Also discuss on there results. Thank you

@graspengineering9249 3 жыл бұрын

Thanks, will do!

@shridharkumbhar6082 5 жыл бұрын

thank you

@graspengineering9249 5 жыл бұрын

Welcome !

@sidibomma15 Жыл бұрын

Good explanation sir.Nice Video

@graspengineering9249 Жыл бұрын

Thanks and welcome

@abdulharissiregar3118 5 жыл бұрын

thank you sir, i was searching type of support for tubesheet, baffle and tie-rod heat exchanger cause my final task about stress at tubesheet causes thermal and pressure

@graspengineering9249 5 жыл бұрын

Thank you for appreciation !

@offshare2033 Жыл бұрын

Thanks

@graspengineering9249 Жыл бұрын

Welcome !

@mukulwadhokar1192 4 жыл бұрын

it would be great if you make separate in depth video on each of the type of load with full application..like when to use this type of load, what are applications, what is significance of that load etc

@graspengineering9249 4 жыл бұрын

We already created videos covering most of loading condition, please visit our channel page.

@rajkiran5490 Жыл бұрын

@@graspengineering9249 Thankyou

@hosamozo 7 ай бұрын

What about external equipment that already vibrates and it's effect on the structures how can we interpret this loads in the structure if we already know the details. Of the rotating machine while we need to study the strucutr for structural optimization

@SD-sr8uz 4 жыл бұрын

Sir thanks for wonderful explanation. Could you tell whether nozzle thrust force should be applied on flange face always? Nozzle thrust is product of ID * pressure . Please tell the significance of thrust force in ANSYS

@graspengineering9249 4 жыл бұрын

Please refer our nozzle shell junction video, there we explain compensating pressure, thanks. Thrust pressure is always applied at the openings. Like as you said nozzle flange face opening. cylinder cut boundaries,etc.

@prerakvaishnav7512 4 жыл бұрын

For the revolution joint example with cam and crank shaft, I don’t understand how there could be a moment in the z direction. Is that an internal moment or torque to rotate the mechanism?

@graspengineering9249 4 жыл бұрын

Yes

@konderuanil 5 жыл бұрын

i am having little bit difficulty in understanding the remote point and remote force. Can you please do simulation of any example using these boundary conditions, and tell us how they affect the results

@graspengineering9249 5 жыл бұрын

Remote point is element created as desired location on which we can apply loads like force, moments as well as can apply boundary conditions. Please refer more video's in description link where mass is applied at remote points. Remote point can be created either as deformable or rigid surface behaviour.

@saraelbahji4524 5 жыл бұрын

Thank you very much .I always thought that the weight is automatically taken into account by ansys. is it necessary to apply it in any analysis ?

@graspengineering9249 5 жыл бұрын

To account the weight effect of mounting mass we need to apply gravity in static analysis. In case of dynamic analysis, no need to apply gravity.

@saraelbahji4524 5 жыл бұрын

Thank you very much!

@vsidrvich 3 жыл бұрын

And one more remark about bolt pretension. In classical ansys it is possible to manage the history of pretension, but is it possible in worckbench. In all videos pretension for all bolts conducted thru one load step, while in reality pretension conducted thru multiply load steps. Is it possible to make a video describing sequences and patterns of bolts pretensions.

@graspengineering9249 3 жыл бұрын

Bolt pretension is assembly/installtion load which comes first and hence in first step preload is applied and then second step is locking and then next step (or second step) onward remaining loads will come. This is the generic bolt pretension load sequence.

@AM-of1hx 4 жыл бұрын

Can you clarify when we need to make different load steps? For example if we have internal pressure, pressure thrust and nozzle forces/moments. With thanks!

@graspengineering9249 4 жыл бұрын

If the pressure vessel is fails due to applied combine loads. Then it is difficult to identify for which loads, vessel is failed. And hence individual loads steps are solved to see the effect of every load case. Like first Pressure, Nozzle forces and both combine.

@AM-of1hx 4 жыл бұрын

Grasp Engineering thanks that very helpful

@vamsisrikanthrallabandi7015 2 жыл бұрын

sir for Ansys ,catia software latest version graphic card is necessary to run, if yes how much size we want please tell me

@graspengineering9249 2 жыл бұрын

For ANSYS discovery, you might need A dedicated graphics card with latest drivers and at least 1GB video RAM.

@Manukrishna10 2 жыл бұрын

Sir can you explain about a shaft like structure , consider only the shaft and no other joints how will we do it??

@graspengineering9249 2 жыл бұрын

what you want to do on shaft ? what is scope or purpose ?

@omargaber3122 Жыл бұрын

Can I download ready-made geometric drawings from the Internet and make modifications to them?

@graspengineering9249 Жыл бұрын

Yes, Just put references from where you are downloading or referring.

@shrivatsahakki2223 4 жыл бұрын

Hello sir please add playlist of videos related to Ansys mechanical APDL

@graspengineering9249 4 жыл бұрын

Okay, Sure..

@shrivatsahakki2223 4 жыл бұрын

Okay sir thank you

@vsidrvich 3 жыл бұрын

You appying loads on your construction simply multiplying value per m square on length of your beams is it correct approach? As far as I know load must be applied according to tributary areas and while your beams are working in equal conduitions and connected in one level the form of tributary are is rectangle.

@graspengineering9249 3 жыл бұрын

This is just demonstration for types of loads. You just need to check the units of the loads while applying and check the output reaction to verify load applied correctly or not. There are number of ways to apply the loads, you need to verify

@vsidrvich 3 жыл бұрын

@@graspengineering9249 One more question. I meshed my model in spaceclaim import it and try to apply a bearing load in workbench, i selected faces of my geometry select apply geometry and nothing happened i/e workbench did not apply bearing load how this problem may be solved?