How to install a Madjax® Ultimate Plus Light kit on a Club Car® Tempo Visit us online at www.nivelparts...
Пікірлер: 26
@keithsheeley303125 күн бұрын
Is there a similar video for the Tempo Gas model? Thanks
@Indiansmoke13 жыл бұрын
Installing now thanks for video.
@nmotionproductions293 жыл бұрын
Nice Install!
@user-bo7sw7bi7b Жыл бұрын
@Ulrich Did you have any problem with the headlight clips not engaging?
@treyjohnson848110 ай бұрын
@madjaxTV is there anyway to disconnect the brake light 3 minute delay?
@noahboock2 жыл бұрын
Is it safe to assume that purple is positive and black is neg for the horn? I’m adding an aftermarket train horn
@stinkenlinken Жыл бұрын
Note, the instructions in the video are wrong about the size of the hole saw necessary for the rear tail light installation. You need a 1.5 inch hole saw to alllow the connectors to slide back in. Please fix this.
@user-bo7sw7bi7b Жыл бұрын
Did you have any problem with the headlight clips not engaging?
@kraigkugler7022 жыл бұрын
Can this kit be installed on a Tempo Lithium ion? Any difference in installation for the lithium models?
@charlesphillips40953 жыл бұрын
Which wires can I tie in lighted side mirrors to?
@Indiansmoke13 жыл бұрын
thanks. gonna buy the kit.
@costenbaderandrew3 жыл бұрын
Will these work in a cowl that already has the standard tempo lights? Can you simply notch out what’s needed for the different shape of these or are they smaller?
@MadjaxTV3 жыл бұрын
Andrew, we would need to know more about the light you have on the cart. You can contact our Tech Support line @ 800-959-0852
@stinkenlinken2 жыл бұрын
Has anyone installed this kit? Any issues or tips to share? How does everyone find the light output?
@stinkenlinken Жыл бұрын
You mention putting the controls harness on a flat metal surface. You didn’t show where you attached it. Perhaps you can supply a picture of how you did that and a location. Did you have to use another piece of material? Thanks.
@danielwarshaw1167 Жыл бұрын
Ulrich, did you figure out how to do this?
@stinkenlinken Жыл бұрын
@@danielwarshaw1167 yes. I got it done. I used a plate from an electrical box and drilled it for the screw holes to line up and then mounted it inside the battery compartment just on the plastic wall. Drywall screw’s work.
@danielwarshaw1167 Жыл бұрын
@@stinkenlinken Thanks for the quick reply. Any installation tips that are not covered in the video and are you happy with the product?
@stinkenlinken Жыл бұрын
@@danielwarshaw1167 I think that the lighting is very good. It is bright and good pattern. I usually turn on the high beams as they seem to be more of a low beam so they provide even more ground coverage. The only thing is that the kit is quite bulky and it takes a bit of work to get it all to fit in the dash.
@danielwarshaw1167 Жыл бұрын
@@stinkenlinken Thanks again. I'm waiting for it to come in and give it a try
@donnaclem41303 жыл бұрын
where's the time delay for the brake?
@MadjaxTV3 жыл бұрын
The time delay is built into the black box module located behind the dash.
@treyjohnson848110 ай бұрын
Is there a way to reduce the brake light delay? It seems to be set for 3 minutes and I want 0-3 seconds
@treyjohnson848110 ай бұрын
@@MadjaxTV how can I adjust to no delay for brake lights. Thank you, I love the light kit and saved $600 in labor doing it myself!
@surroundedbyjaggoffs Жыл бұрын
Saftey glasses to drill into plastic??? Hahahahaha