I think thats 10-15% lines infill and thats not that high.

I said I use cheap filament when layer lines don't matter. It's not a matter of cost. Chip clips don't need to be beautiful.

Just over 8 minutes with their built in benchy which is optimized g-code like all other printers. Those are always optimized though I saw another Livestream and that's how long it took but the quality was good.

Defaults all the way. 0.4mm nozzle. Don't remember they later heights. As the previous person said, about 8 mins for benchy. Predator too 2.5 hours. Gauntlet pieces were around 2.5 to 4 hours a piece (large vs small). For shelf-worthy, I'd slow it down a bit and use better filament.

If I had a P1S to compare it to, I would. We do have a T1 coming for review as well though, so stay tuned!

Been patiently waiting on the T1 since November. I have the P1S and with the AMS and its capabilities there’s no comparison. I had a Q5 and SR and although fast for their time, multi color printing was difficult but not impossible. As soon as I got the P1S, I regretted my T1 order but I’ll still give it a good shake down if I ever get it.

yeah i would be interested in that one

I don't think it will be out for a bit longer for a few reasons. First. The S1 is actually available on FLSUN's website right now and I'm mostly because the specifications are incomplete. The AI stuff still says coming soon but mostly because it doesn't list the MCU The S1 is using a quad core 1.5Ghz ARM processor, which is very impressive. Either FLSUN hasn't decided what MCU to use or they aren't updating their website. It has the same print accuracy, 1000mm/s and 90mm/s flow rate, same fab setup, just 30,000RPM instead of 40K and 30K acceleration compared to 40K for the S1. It's biggest advantage that I see is it's using 36V Closed-loop motors which I believe is a first for any 3D printer. It also says it has real time filement detection so it can give you a rough estimate of grams of filament left. S1 says heated up to 50C which really isn't that impressive. I don't believe LIDAR adds anything. You can't use it on PEI sheets but you can now? I get software is different but a PEI plate isn't smooth. Additionally Pressure Advance and Flow Rate go hand in hand The T1 at its current price is simply a better value. Smaller build plate, no LIDAR, but a camera with the same spaghetti and something on plate detection. Cheaper but still carbon filtered enclosure, similar to Z1 vs P1. I don't think the S1 is worth 1K more than the T1 but I have a feeling the T1 price may go up. If not before launch then soon after. I have seen VZBot AWD Core XYZ get to 2000mm/s at 0.16mm height bit also had a water cooled hotends to cool the stepper motor and extruder and all the and all the stepper motors are water cooled.. AaWD just means 2 stepper motors for X and Y (four total) and shorter belts. With shorter belts it resonates less so input shaping doesn't kick in until higher speeds and 2 extra stepper motors gives you that. It's also open source and ou have to build it yourself so..... With that said the VZbot team said their next printer ter is going to be a Delta printer ter for the speed advantages over Core XYZ

@@JoshFisher567 I got an email saying it’s shipped and will be here July 10th.. we shall see.

Not going to lie, it's not quiet. I don't have a decibel meter handy to test it though

Its 71 dB at full tilt.

@@ravenovatechnologies6554 whoa. That is not "not quiet", that is LOUD :)

Julieta -- do you have a particular file you'd like to see printed at maximum quality? I'd be happy to slow things down and print something on the other end of the quality spectrum. :) Ping me at burke@gamingtrend.com and let's chat.

Yep. Embargos are normal in this industry. :)

Review embargos, when they set the release date far enough away from the reviews so customers can make an informed decision, are probably a good thing for reviewers. They allow for all reviewers to prepare and take their time with the review and be thorough and not worry about racing against other content creators to rush to be the first video up.

@@Matt-ps9iz Exactly! It helps us all stay on even footing as well. Smaller sites and bigger sites get the same embargo, and readers get to hear about it before they put down their hard-earned money. :)

I was shocked when it showed up. hahaha

Realize that it doesn't print at 1200 consistently. That's max speed.

@@GamingTrendVideos yeah I know that it depends on the model the curves the detail I get that it could probably do a circle at 1200 I'm not a moron or new to this, why does so many people on the Internet assume something before they reply to someone.

I dunno. You came across pretty hostile, implying I'm a moron. But hey....it's the internet.

@@GamingTrendVideos hostile? LOL stating a fact is hostile now? I didn't call anyone a moron u did that all by urself

Have you personally dealt with FLSUN support? I haven't in it they could be great or terrible, what was your personal experience with them like? The T1 for the price crushes every printer you mentioned on paper, 600 US for 1000mm/s, 90mm/s volumetric flow rate, 30000mm/s acceleration 30K fankije S1, AI detection and camera. It's essentially this with a non metal chamber and smaller print area. No spool holder/drying box above it and no LIDAR either. It's the P1 equivalent of the X1

I printed them at Max speed, as I said in the video. For pieces I'll put on the shelf, I'll slow it down.

@@GamingTrendVideos i kinda think that is the issue, its advertised as one thing. but very poor at that. so if you slow it down... there are alot better cheaper options then this lol. Thing is all your prints showed here are poor quality looking like delta artifacts, extruder not being able to to consistenly extrude and or simply unerextruding. i get that your setting it at max, but speed dosent matter if it looks worse then the stock first gen ender 3 imo

@@tobiaspersson7320 For some things I'm gonna print top speed. For some things I'm gonna go smaller nozzle and slower. I appreciate it when my mom says "Hey, XYZ part is wearing out" and in a matter of minutes she has a replacement in her hand. For things like this gauntlet, it's gonna need slower, smaller nozzle, or more sanding. You print -- you get it. It's a tradeoff, and always will be.

@@GamingTrendVideos Yeah, i do print. Which is why i dont get why you need a smaller nozzle to just run finer layers. ie 0.12 or even 0.08. 0.4 should handle this fine. Issue is still that at the speeds you have ran the extrusion does not look consistent. If this would be an PLA issue it would not look like this at all. If they say or state that it is. I really dont understand why they havent sent you abs instead of pla to test with since its better at flowing at highspeed and would require less cooling. the more i think about this the less sense it makes tbh. its either the hotend or extruder thats not keeping up

I wanted to show the direct out of the box printing quality. You can of course go slower, and you can of course swap out the nozzle if you need something tighter than that

I'm not convinced either but I was surprised that it ships with a 0.2mm and 0.4mm nozzle. It shows that FLSUN thinks it can. 0.2mm is rare to get with a new printer but can print smaller layer lineswhich typically results in better detail. Now how fast you can go while remaining at that quality has yet to be determined I'm glad they used a standard for the nozzle size, because of Bambu more are moving to proprietary hotends which sucks. If this can do the flow rate it claims it proves that companies saying it's needed for fast speeds is all a lie, which it is. If you want detail resin is obviously way better but the size restriction is the biggest issue, that and chemicals.

Except that it's NOT. It's not a seam. That's a smooth part in the slicer, as you can see earlier in the video.

​@@GamingTrendVideos is it possible that it may have just been a bug in a slicer that wasn't properly showing the seam line? It's hard to tell from the potato video quality but that thing 100% looks like a seam line.

*shrug* I didn't receive your list of requirements in time.

Amazing for everything else

Umh…. Are you drunk? 😅

Hasn't been my experience. *Shrug*. I can only go off what I've seen. I can't judge off other people.

@@GamingTrendVideos Shill