Unleash The Power With 36 Volt Sleeper Powerwheel Build!

Рет қаралды 4,441

4 ай бұрын

Customer dropped off a 6 volt bmw powerwheels and just wanted it to work properly, we took that as a challenge to build a insanely fast sleeper beemer!! Took the parts he already had, which included two 12 volt gearboxes and motors that replace the single 6 volt motor. Added a second ryobi 18 volt power tool battery adapter for 36 volts of motor melting lithium power. Installed a universal electronic speed controller (esc) that has built in reverse. Power feeds into a 28 volt dpdt relay to add braking. Check out the video for details and the included wiring diagrams we used to build this crazy fast electric power wheels ride on car. Purchasing from the following links helps us create these videos.
Digital volt meter- amzn.to/3wTfSNW
Ryobi battery kit- amzn.to/49VsnHp
Ryobi adapters- amzn.to/3vds37N
Speed controller- tncscooters.com/index.php?rou...
12 volt gearbox/motors- amzn.to/43iIOuR
Silicone racing wire- amzn.to/3IB5Qnd
24 volt dpdt relay- amzn.to/3PjguCS
Key switch- amzn.to/43jiwZi
brake resistor- amzn.to/4cdocIA
governor potentiometer- amzn.to/3vka1Rf
Metal foot pedal throttle- tncscooters.com/index.php?rou...
Plastic smaller foot pedal throttle- amzn.to/3wQVe0R
Connector kit- amzn.to/43eUAX0
Crimping tool- amzn.to/48OEpkp
3 conductor governor wire- amzn.to/49X6Ez2
Upgraded battery and motor connectors- amzn.to/48Rl4iM

Пікірлер: 23

@gasaxecustomsaws 4 ай бұрын

This is amazing! I've been looking into something similar for my daughter's Jeep. Thank you for doing this video!

@EricPriceOfLouisville 3 ай бұрын

I came because I'm new to Power Wheels and doing this for a friend...I wired up 3 12v LiFEPO4 20AH batteries so the system is parallel when it's off for charging...and series when it's on for 36v (Just Over 40v at full float charge). Your potentiometer needs will be directly related to the minimum voltage of your controller and the maximum voltage of the system...if you've got a 24v controller on a 36v system, you'll need 300 Ohms (approximately) to achieve full usage of the potentiometer.

@unfinishedbusiness830 4 ай бұрын

Pot on the pedal output is GENIUS!! or should it be BEFORE the pedal...?

@CustomKidzCars 4 ай бұрын

It's in the middle of the signal wire.

@ammuscl Ай бұрын

If you don’t mind, how much would you charge for a setup like this in a power wheels Barbie Jeep? I’ve got the 18v Ryobi batteries and adapters but that’s it. I’d love to get my daughters jeep moving faster but don’t have the knowledge to put all that together

@user-dd7se8qh5y 11 күн бұрын

tutorial for installing engine sounds, boss

@codyspearing 2 ай бұрын

I love your video. I was just wondering if I could bypass using a controller and use a soft start module with voltage regulation?

@CustomKidzCars 2 ай бұрын

R u referring to the cheap Amazon versions used on many models? If so it's possible but I am not impressed with the performance or reliability

@tomschreiner2132 3 ай бұрын

Thanks for the Video, it was very helpfull for my build. Would you please share which controller you used? Can't find a 36v with reverse, just 48v and 24v :(. Thanks!

@CustomKidzCars 3 ай бұрын

I put a link to the site in the video description for all the parts used. Thanks for watching

@joshuaroberts4024 Ай бұрын

I got the key and motor controler you linked to but the controller outputs seem to be different than the video. I wired the key to the controller output called "speed selection switch" and all 3 key positions spin in the same direction. Do you use the reverse switch connector? That one only has 2 wires.

@Rhoop24 17 күн бұрын

I’m in your boat currently. Did you find a solution?

@alexleklund 4 ай бұрын

So the 24v speed controller handles the overvoltage with 41v from fully charge 18v Drill batteries ?

@CustomKidzCars 4 ай бұрын

Yep, just wont have lvp but the Ryobi battery has lvc built in

@samueltorres4576 2 ай бұрын

Where did you get those motors that can handle 36v? I hooked up a 36v lithium battery in one of our power wheels dune racer and it immediately burned up the stock motors

@CustomKidzCars 2 ай бұрын

They don't handle 36 volts as discussed in the video. They already smoked one motor. That is the reason for the potentiometer to turn down the power

@MichaelV-rf4me 2 ай бұрын

Great video! I've copied this setup, added the low voltage cutoff, and everything works great except the pot. that darn thing seems to do nothing. when attached, i'm getting full voltage no matter where the dial is set. I have the Plastic smaller foot pedal throttle and the pot you recommended above and installed the pot on the green wire. no dice. not sure what to try next.

@CustomKidzCars 2 ай бұрын

Should be spliced into the white signal wire

@markthompson1713 Ай бұрын

@@CustomKidzCars First off great video Thanks . The pedal that I used had red, black and yellow wires. I had no glue on which wire to cut into. So I cut into the yellow first. And got you full voltage problem. I soldered the yellow wire back together and when for the red wire. And that did the trick. So it was the red wire with my pedal setup. Again the video was a great help. Thanks.