This is intended to be a better updated video showing a NEW pilot what to do with this new planes he or she has and how to get it going with a NEW Spektrum RX system. From making a throttle cut to performing forward programing!

After watching many hours of videos trying to set up SafeX and gyro system I thank you for such a clear video that I could understand and get set up correctly. Thanks so much.

I think Spektrum owes you a ton of money for explaining these concepts in simple terms much better than Specktrum's in house produced videos, thanks. I'm moving more into balsa planes and this is an excellent video on setting up a plane properly. Thanks.

I agree with the previous post, much better explained than the Spektrum videos. Even though I knew all this, learnt from hours of playing around with the NX8. It was still great to watch and see someone show new comers how to set it up from start to finish. I had never heard of forward programming. Had not a clue what it did and how to apply it to a model. If I could have seen this vid it would have save me from brain fade lots of times. 🤣🤣🤣🤣🤣🤣

I was about ready to throw this transmitter against a tree till I ran across your video. Thanks for speaking in terms that a newbie can understand.

Great video on setting up the plane and AS3X/Safe. Simple and straight forward.

Thank You! I think I can get the Expo concept more clearly now. Your explanations are very helpful👍

One of the best, if not the best, tutorial on the covered subjects. I think I would have mentioned/added how the third position on the modes and rate switches might be used - e.g. Mode position 3 = no SAFE and no AS3X; 3 position Rate switch = Low, Medium and High.

Thanks for putting this video out! It’s a nice refresher for rates and expo settings. You’ve made me understand the concept of expo settings. I’m still stuck in the dark ages with my DX8 Gen 2 transmitter. I see how more versatile the NX10 really is. Perhaps one day I will make the transition out if the dark age. Anyway, thanks for another “how to” video!

Thanks from Australia Mr Fat Guy

Hey there friend Just wanted to say thanks for the video tutorial on setting up a new receiver, as3x , expo and such on your arrows trekker As I’m new to the hobby it can be a bit overwhelming to figure out how to do some of the technical stuff. Love your videos, keep up the good work. 👍🏻

Thank you for a very informative video. You teach as if you want us to learn instead of some of the fast talking smarties that are only trying to impress you on how much they know instead of trying to teach us beginners. Then when you try to contact them, well I'm amazed that how many companies have an employee named CHAT...who will never be an employee of the month. Thanks again and I'm ready to go apply what you have explained VERY WELL. Love to watch your videos.......HAPPY FLYING!

Well what can I say. I today followed this video, successfully added an AR630 to Bigfoot. Only one thing - How to add the Panic button to this setup. Thanks this worked a treat.

Where was this 2-3 years ago when I started. Good job 😎👍

hello, you are excellent !!! i know the subjects you explained and was curious to see you explaining them. Congratulations !! Nice instructor

very good video easier to follow than the spektrum's video great job one thing , I like to set flight mode 1 to inh for everything which turns the AS3X off this is just in case the receiver comes loose in the aircraft then use flight mode 2 and 3 for AS3X

Just set up a new AR631 watching this video. Thanks of the help.

Thank-you for all your advice. It has made me more confident when flying, especially the scale airplanes.

Thanks!

Was helpfull to me. thank you

Nice video for us noobs. Thanks for the videos. Much appreciated

Dear Fine Guy, I am in awe. You have provided me with the pieces I needed to have fun and not frustration. You are a fantatic teacher and an absolute asset to me as a new flier. Kudos kudos kudoos. I do have one perhaps silly question. When I change my receiver over to the 630 or thhe 631 on an fms plane with reflex, do I take out both the reflex and the receiver or do I leave reflex in. My thoughts are to take out both and just go with the Spek 630 or 631 Thank you so very much for giving me a clear and concise explanation to now enjoy my hobby ro its ma. Your student from Canada 🇨🇦 Bob

Thank you!! Needed this info

Fantastic video! The video that always should have been made! Thank you!

Hi there, Great Guy, you have the best channel:-), and I like your style! Your instructions are easy to follow, and I use your videos as tutorials step-by-step when programming. I have a problem, that perhaps you can solve/explain to me: I have a NX10 radio and an unused AR8360T receiver that I bought about 2 years ago. I am now planning to use this in an AeroScout 1.1 Trainer (in which stock RX is the AR631 that is factory pre-programmed with AS3X and Safe), and I have used the new unit to include the Flaperons function (which needs one xtra channel). I changed the Y Aileron harness with two single leads, one to pos 2 = RAR and the other pos 6 -=LAR (AX1). Pos 4 is RUD as usual, and pos 5 is now GY1 (gear). Pos 7 = AX2, but I dont know what I control there. When I operate the Flight Modes, AX2 shifts from -100 to zero to 100. Now, it should be possible to fly the model, because all rudders go in the right direction, but I am unable to execute the Forward Programming function. The Other Programming function: I try to execute 'Factory Reset', but it will not execute the command. Somehow, the system is out of whack. It is possible that I have chosen wrong locations (pins) for the functions AS3X and SAFE, and that is why the RX wont budge. Best regards, Rolv (Norway)

Takk!

I was trying to set up as3x step by step using your previous video. Switch B for flight mode seems ineffective, staying on FM2 no matter where the switch was. I did stumble across the as3x gains being controlled by the Rknob. I suspect there is some way to capture gains, but the switch not changing the flight mode is aggravating. There seems to be automatic call outs when I moved switch B calling out FM 1, FM2 etc. but the screen stays on FM2 the entire time. IDK. When I figure it out I'll post the solution in case someone else is having the same issue. Thanks for updating the forward programming procedure.

Tthanks😅

Can you use rates and expo when you are flying with safe on

Do you first do a maiden flight and then setup SAFE/AS3X or can you install it right of the bat before the maiden flight?