The first time I ever changed brake pads I was surprised how easy it was. At the same time I was annoyed at just how much shops charge for such a simple job.
@jasontackett639611 ай бұрын
1. Its not always simple 2. Theres a lot more maintance that goes into but yes easy cheap way to just get it done without taking the extra steps will get you by.
@oddarntnes707910 ай бұрын
a shop will almost always do a more thourough job than this guy.
@lobasboyfriend807310 ай бұрын
@@oddarntnes7079this is something a mechanic would say 😂 youll so salty people can do your job watching a 30 second youtube vid
@alx995010 ай бұрын
@@oddarntnes7079I paid 900 for a break job and they didn’t grease a thing
@ericsalinas9810 ай бұрын
@@lobasboyfriend8073he didn't show the part where you have to pump the brakes or he would've been rolling down the street unable to stop 😂😂cant fit everything in a 30 second video 🤡
@johnnyespinoza6861 Жыл бұрын
Its probably not a big deal but the way he tighted the lugs had my heart hurting
@jaybutton3004 Жыл бұрын
He star pattern takes them off Then tightens them 1 next to 1 I saw it too 😭
@davidw1640 Жыл бұрын
And there's not a Torque Wrench in sight 😂
@jacobflack406311 ай бұрын
Right
@johnsonchan85326 ай бұрын
Noob
@danielorta5988Ай бұрын
Lol I was thinking the same shit, how u Gona show us something an then totally do a shit job putting your tire back on
@johngrefer9799 Жыл бұрын
My God finally someone who knows how to use a cordless rachet first break the bolt lose then take it off wow.
@SD-et4gv2 ай бұрын
Look ez as 123 for a poor man like me that can't afford all that extra stuff an money I don't an no time for ❤😢
@x_verifying-_-7091 Жыл бұрын
Forgot to grease up the guide pins or you’ll have uneven pad wear
@prestonweldon9084 Жыл бұрын
I was about to comment about that that's a typical rookie mistake
@babyproductions5523 Жыл бұрын
He tried his best he doesn’t seem like he knows a lot didn’t do the thing right and didn’t tighten the wheel in start pattern man needs post stuff that’s correct
@cjadventures8840 Жыл бұрын
Wait the guide pins? What’s that
@jayvito3667 Жыл бұрын
@@cjadventures8840fr
@3o5maniak Жыл бұрын
@@cjadventures8840 I think the pins he’s talking about are the two bolts holding the caliper
@eduardogalindo5588 Жыл бұрын
Why did he bolt in that tire like that 😅. Your supposed to go in a star patter.
@alexesparza6171 Жыл бұрын
Dead ass first thing I noticed 😭😂😂
@mmmmm-ne6zn Жыл бұрын
@@alexesparza6171 right!!!
@eternalbliss5189 Жыл бұрын
This is super important 👍🏽
@disastreee Жыл бұрын
and dont use impact
@vwwrenchie314 Жыл бұрын
Probably be cuz like the rest of the job he didn't know what he was doing anyway not a good video
@rhouser1280 Жыл бұрын
Dude, I’m sorry, I hate to be that guy, but you left out about 15 steps. I could see if it was an air filter but peoples brakes, come’on man
@fredsanford33623 күн бұрын
Yeah, now a bunch of dvmb broads and fruity “men” will think they can change their brakes 😂🤣
@cormet55os2811 күн бұрын
Agree
@DevilDog83 Жыл бұрын
He forgot to mention that if you use a “C” clamp to use the old pad for the clamp to push against the piston.
@salfetka28 күн бұрын
Amazing short video explaining everything. Thank you
@chicagocrazy5740 Жыл бұрын
Tip: you can just removed the bottom caliper bolt and let the top one loose, that way you can just slide it up
@tyharris78 Жыл бұрын
would you still have to compress the caliper ?
@chicagocrazy5740 Жыл бұрын
@@tyharris78 is a must.
@tyharris78 Жыл бұрын
@@chicagocrazy5740 yes did it yesterday , needed to make space for the new pad
@janetyeoman15446 ай бұрын
Best to remove both bolts, remove slider pins, clean and re lube pins for a smoother action. Especially if you live in the rust belt or Canada.
@giovannialicea2415 ай бұрын
You have to lose both to grease the guide pins. The guy in the video didn't do it.
@whatdadogdoin7531 Жыл бұрын
No not yet. You need to pump the brakes to make the caliper piston stick out. Otherwise the brakes won't be applied. Also loosen the brake master cylinder cap to vent off the pressure when compressing the piston and make sure no brake fluid spills out
@jimiboii209 Жыл бұрын
Thank you
@socer451 Жыл бұрын
I'm a visual learner....need to see this done.😂😂😂
@GODISGREAT1227 ай бұрын
❤❤❤ Very informative.
@ismailali32506 ай бұрын
Pump the brakes when
@whatdadogdoin75316 ай бұрын
@@ismailali3250 after you have installed the new pads and put everything back in place
@FooShiestyOG Жыл бұрын
followed you instructions now I needa to the mechanic for a fucked up break line because you didnt tell me I needed to hang the caliper
@duckwildcodyjames4330 Жыл бұрын
You only have yourself to blame, you can clearly see he has his calliper supported so it doesn’t fall and bust the line.
@andrewleos9803 Жыл бұрын
🤣🤣 you listened to a KZfaq short.
@DroopyLoops Жыл бұрын
Pretty sure you made that up after seeing him not say so. Any competent person would know to support the line
@OffendingTheOffendable Жыл бұрын
Maybe watch a proper video next time
@guacamole6856 Жыл бұрын
Prettt sure this was a joke… y’all just don’t get it
@wachofelix45603 ай бұрын
Torque specifications for lugs and bolts, when pushing piston back open bleeder valve then close with torque specifications , wire brush and clean wheel hub and caliper bracket and lubricante bolts and hardware and back of the brake pads as well. White lithium is good.
@pollux2825 Жыл бұрын
grease the slides pins whenever you take the caliper off, and tighten to wheel in a star pattern, also when you change the pads you usually want to change the rotors too. the rotors surface will cause uneven pad wear.
@CumminsTech24 Жыл бұрын
Resurface the rotors. Look for the lip on the rotor, if you have a lip you’ll be able to resurface without risking safety
@lonewolf2205 Жыл бұрын
You don’t have to change the rotors every time you swap pads, for each car it varies because you must measure rotor thickness and taper. I work at an auto shop and we usually recommend a rotor change due to if the rotor is out of round of 3 thousands, this is because it causes a big pulsation on the brake pedal, a dial gauge helps with the out of round process check, and we use micrometers to measure the rotor on 8 different areas around the rotor. If the rotor is not out of round and is in specifications it doesn’t require replacement, if it falls out of specs it does. I also did see a comment on resurfacing as well, some shops do it while others don’t. Mostly today it’s kinda rare to find a resurfacing shop out there, but they still do exist. The reason why shops don’t do it is labor costs, each rotor to resurface takes about 15 minutes to having to do a rough cut and slow cut. That’s why so many shops stopped because we lose our shop efficiency, plus resurfacing causes the rotor to be thinner (obvious) but it makes it more prone to warp if the rotor is hot and gets splashed with water causing many customers to come back. It just becomes a big hassle, but hey, if you have a perfectly thick rotor that is newer by all means get it machined!
@TRUMP20Z42 ай бұрын
Great channel!!! Ty
@jonathancabrera8721 Жыл бұрын
Didn’t need to take the whole caliper off for just pads u just had to remove the bottom bolt lift the caliper and put the pads on 👍🏽
@Trashmouth75 Жыл бұрын
Agree, could have just done one
@GODISGREAT1227 ай бұрын
Thanks
@thelegendkillergus74517 ай бұрын
Thanks buddy your saving a lot of people money also is something new that they will learn 👍
@_monti1423 ай бұрын
hello? just make sure its thight wont cut it, wheel bolts have to be torqued to spec, same for those caliper bolts
@Rebirth602 Жыл бұрын
Cant describe how bad it is for the caliper piston to have direct pressure on the inside of it. ALWAYS use the inner pad as a back stop to compress the piston.
@thegreatrelease4539 Жыл бұрын
Jack stand? Grease slide pins? Replace old pad clips.
@bossartwork22692 жыл бұрын
You should probably be telling people not to hang the caliper or they will mess up their brake line
@daemonshotz44812 жыл бұрын
True luckily I knew that part though 😂 for the most part this video deserves way more likes.. very straight forward
@MySwagg93 Жыл бұрын
Where do you put it ?
@daemonshotz4481 Жыл бұрын
@@MySwagg93 I hooked mine to the shocks so they stay up
@MySwagg93 Жыл бұрын
@@daemonshotz4481 thanks!
@daemonshotz4481 Жыл бұрын
@@MySwagg93 no problem
@childrey1410 күн бұрын
Forgot to bleed and replace the clips. Also before you put your pads on use brake grease on pads and anit seaze on caliper pins. Same with back of rotor. Just put new rotors on everytime you change the pads too.
@jamesharris8082Ай бұрын
Keep in mind. New cars have electronic braking now so it's not as simple as this video makes it look. Now brake pads aren't that hard to replace you're right about that but Mercedes these newer vehicles are these electric calipers take a lot more knowledge than just this right here.
@user-kg9xu1fg8d Жыл бұрын
What kind of drill is the one you used for brakes
@leoxgamer833 Жыл бұрын
You missed putting the brake lubricant, you compressed the caliper almost right and you bolted the wheel the incorrect way…
@OddDevDGAF Жыл бұрын
Why do you need to compress the caliper
@Lion0305Ай бұрын
Always open your brake fluid reservoir cap before compressing the caliper. You can blow your brake lines if you don’t.
@juliaportillo5485Ай бұрын
This looks 😮easy -- I been paying so much for this.
@chato9347 Жыл бұрын
You're supposed to turn the rotors as well how do you know if they're not warped shade tree mechanic
@vadenummela9353 Жыл бұрын
Turning the rotors down is a waste of time unless theres a significant lip on there. Also if theyre below minimum thickness theyre garbage regardless.
@limamantapachitas6 ай бұрын
Lub the pins with silicone grease very important and the pads ears
@fredsanford33623 күн бұрын
Wow, you didn’t even have to bleed the brakes. Impressive 🎉😅
@username_af21 күн бұрын
Bleeding brakes is when there is air in the system
@SSD54302 ай бұрын
What about break wear sensors? Where are they and do we need to also change them if we change rotors and pads?
@ion-fd3pn23 күн бұрын
i’m a 14yr and i wanna be a mechanic in the future and i wanna learn a lot of things at a young age so i dont have to in the future and its actually blows my mind how smart i am because i have a 16yr old neighbor that doesn’t know how to change a battery or how to change a tire or how to check oil level
@username_af21 күн бұрын
I learned everything I know from youtube
@ion-fd3pn19 күн бұрын
@@username_af dang imma needa try that
@GabrielGarcia-hz3ouАй бұрын
Do I change all 4 tires then press the brakes to get the pistons to adjust or change front then back
@kevinmiller5467 Жыл бұрын
Sometimes you are paying for them to tell you that you need a new rotor.
@victorchan6817 Жыл бұрын
It’s also recommended to change the rotor as well
@mouhijarvenkeisari3118 Жыл бұрын
@@victorchan6817 no it's not😂
@mynamedoesntsayanything4318 Жыл бұрын
@@victorchan6817 you just get it resurfaced
@vadenummela9353 Жыл бұрын
@@mynamedoesntsayanything4318 if theres a significant lip its worth it to turn your rotors down yeah. But 99% of cases removing a used rotor and putting it back on is waste of time.
@yashshah6328 Жыл бұрын
@@mynamedoesntsayanything4318 Resurfacing a rotor is not worth it anymore. better to replace it with the pads. Fresh Pads, Fresh rotors is the best way to go.
@davidtodd2555 Жыл бұрын
I did that but my pedal goes to the floor. What did II do wrong??
@edgarcx3447 Жыл бұрын
Bleed the brakes
@GnosisJordanАй бұрын
I don’t understand the compression of the caliper portion. Can someone explain it to me?
@drewskey05 Жыл бұрын
Changing pads deserves (and requires) more than a youtube short 🤦🏼♂️
@thatslammed392Ай бұрын
what are the bolts holding the caliper in called i have to replace one but everywhere i go they only have these huge bolts
@chrisr326 Жыл бұрын
Love simple, informative videos. Appreciate you cutting out the fat👍
@mowman7777 Жыл бұрын
It’s best to install new or resurfaced rotors too.
@pinkfrank4 ай бұрын
Didn't lube the slides didn't change the clips and didn't do the star pattern to put the wheel on evenly. If the tire was rough coming off it might not seat right putting em back on tightening the way he did.
@Jjejdh8 ай бұрын
OMG IM INLOVE WITH YOU 😭💓THANK YOU
@928guyАй бұрын
"Pad Slapping" best to have those rotors replaced with new pair, or have the old pair turned (if they weren't that worn).
@jamesharris8082Ай бұрын
Show a video of those electronic brakes and show how they're done and you'll see the difference in how hard it is to do them and why stops can charge a lot of money it's not that expensive to do but it is a little bit of everything to do and you got to have special tools.
@frankstewart6734 Жыл бұрын
There are about 50 different kinds of calipers. Piston types. Electric brakes. You also didn’t check for disk wear. It’s not all that easy.
@ijgi043 күн бұрын
Any idea on Caliper bolt torque value?
@cnbwllkm Жыл бұрын
What if car has electric parking brakes. What tool are you going to use for those type calipers. What if the rear caliper pistons need to be turned in, what tool then?
@Brandon_winkle10 ай бұрын
What wrench did you use? 3/8 Milwaukee??
@Itz.lazyjake11 ай бұрын
Why do you need to compress the caliper?
@theone426211 ай бұрын
So the new wider pads fit.
@Effytowers2000 Жыл бұрын
Beginner here but why do u need to compress the caliper? I’m confused on that part. Of every video I watch
@joepando291 Жыл бұрын
Same lol
@JustaShrimp372 Жыл бұрын
The pistons in the brake compress when the pads get wear. They push them out to fit the new, thick ones
@the_unkowngod_2328 Жыл бұрын
Easy answer is try to fit the caliper back after you put on new pads than youll realize 😁😁
@brucew.mcosker6063 Жыл бұрын
To create more space for the new, thicker, brake pads. The older ones are worn thin and the caliper is closes to that size pad.
@dondada194910 ай бұрын
Why does my car feel like its braking when I accelerate?
@MattGuzman-ng2yx10 ай бұрын
You're dislexic, and pressing the opposite/wrong pedal. 😃
@Tiffany-lw3po Жыл бұрын
Does anyone ever take the brake reservoir cap off? Just saying it makes it easier to compress
@miltict928 Жыл бұрын
Just careful not to suck any air in
@DarkReaper-or9el Жыл бұрын
id suggest you look at a detailed video like chrisfixes as this is not detailed and so many things are wrong
@samanthamay4189 Жыл бұрын
Amen love Chris fix videos.
@gdbro3842 Жыл бұрын
Don’t forget to send and lube at two pistons
@calviny938411 ай бұрын
Somethings are not meant to be in Shorts format. If you've never done your brakes before, find a more in depth tutorial
@MattGuzman-ng2yx10 ай бұрын
This is what landed me here. I didn't think it was this simple, of course, just wanting to get the gist of what I'm getting into. But I kind of thought some impnt steps were missing. There was good advice, but yours is the best! That's what I'll do, and Thanks! 👍
@MEWASTREL9 ай бұрын
@@MattGuzman-ng2yx You and me both. Got a 2000 camry, and she's squealing like a stuck pig. She's my daily, so learning how to do this will not only teach me how to work on my car (as a man), but save me money as well. I'm an avid believer in "you get what you pay for," well, I'm not paying some schmuck all my hard earned dough (I'm a mailman) to do something I can do and should be doing myself. I love learning. So, yeah, thanks for coming to my Ted Talk.
@meshachfoster7498 ай бұрын
Jus a psa. Always re-up on grease in the guide pin boots. Tbh idk bout putting grease on the back of the pad, looks sketch and I can't imagine the utility. Always tighten wheel lugs in a star pattern i.e. snug all and tighten each followed by its opposite for even seating of the wheel.
@islandtime1402 Жыл бұрын
All done and not a torque wrench in sight... 😂 You also didn't inspect the rotors, piston, guide pins or replace the pad guides, lubricate anything or put anti-seize or thread locker on. But other than that, yeah...
@terryharvey4811 Жыл бұрын
THAT IS KNOWN IN THE TRADE AS A PAD SLAP.
@vadenummela9353 Жыл бұрын
This is known in the trade as the guy who "had his friend do his brakes" and then shows up 20km later with no pedal.
@noone-pg4lr Жыл бұрын
@@vadenummela9353 why what was wrong with the way he changed his brakes
@vadenummela9353 Жыл бұрын
@@noone-pg4lr no new grease on the guide pins is the biggest sin. Didnt clean the brackets for the pads. Didnt apply copper/antiseize grease to the ends of brakepads. Didnt turn down the rotors. And I could go on about small stuff.
@noone-pg4lr Жыл бұрын
@@vadenummela9353 ok thanks for the explanation I don’t know much about cars
@88cc20 Жыл бұрын
when i compress the caliper do i need to open the brake liquid cilinder lid open ? doesn't it push back air?
@budskrilla2u133 Жыл бұрын
This is exactly how you don’t do a brake job the right way. This is how you half ass a brake job.
@marvin2678 Жыл бұрын
Why ?
@budskrilla2u133 Жыл бұрын
The rotor will need to be replaced or resurfaced before the pads wear out. Most manufacturers have engineered the brakes to be replace all components of worn. He didn’t grease or clean the slide pins. I can go on?
@shadowman199210 ай бұрын
I have done it like this and it has worked fine for 20 k more miles
@teehenare91783 ай бұрын
Dont we have to bleed the brakes
@JimmyLarsen1 Жыл бұрын
You didn’t grease anything or replace the clips
@Black1Pod4 ай бұрын
Dont you need to drain some of the brake fluid? Pretty sure if you don’t the piston inside the caliper will seize when you try to compress it.
@michalakn3 ай бұрын
No
@Peachymilk36577Ай бұрын
Not the pad slap😂
@BingoRebel2 ай бұрын
The way you didn’t consider replacing your rotors along with your pads is the reason us mechanics deal with customers with squeaky brakes
@uninspired35834 ай бұрын
What do you do when the caliper pin snaps off, asking for a friend...
@Lemoncrusher44556 ай бұрын
Putting grease on the back of the pad causes more heat to the pad and wears them out faster.
@hyugon68599 ай бұрын
I usually change out the rotors if its super bad
@enriquenajera89146 ай бұрын
Do one bottom and one top first on the wheel nuts
@enriquenajera89146 ай бұрын
When putting it back on obviously
@tezzasbigbuz3933Ай бұрын
You only need to remove bottom bolt
@jamesdesmond17104 ай бұрын
No rotor cut or replacement?
@juliancamano4424 Жыл бұрын
STAR PATTERN WHEN PUTTING WHEEL BACK ON… jesusssss
@jermainebatedspade Жыл бұрын
Didn’t even smoove out the rotors before putting new pads on
@universelove6163 Жыл бұрын
Can you do a video on how to change the rotors ?
@hitsbluntpodcastkcmo Жыл бұрын
Don’t forget to pump the brakes before you start the car
@Lokz99 Жыл бұрын
Do I need to apply the emergency/parking brake ?
@lavonpegram59698 ай бұрын
Have a blessed day!
@alijahphelps1835 ай бұрын
Trolling at the end.
@austinhernandez271611 ай бұрын
I compress the pistons without taking the caliper off
@robl1967 Жыл бұрын
My caliper doesn't come off that easy after removing the bolts do you know why?
@EgCapalot2 ай бұрын
Why is no one saying this? OPEN YOUR BRAKE FLUID RESERVOIR! Where do you think that air is going when you compress the pistons? Into your damn brake lines, let that air escape
@unikdesigns9500 Жыл бұрын
My caliper does not come out even after removing those bolts. Can I hammer it?
@travaughnanderson3958 Жыл бұрын
No
@B0B_J0HN Жыл бұрын
Chrome sockets are no joke
@gunguy83482 ай бұрын
This is not the right way but I like he was showing it’s not rocket science. I would say this is for emergencies if you were steel to steel and had very little money to keep your car going so you can do the full brake job later
@abdullazizalfadhly84246 күн бұрын
What about the slider pens 😂😂 fuck em yaa , Good job 😂😂😂
@ER_2034 Жыл бұрын
Real easy to do right , looks like it
@josephknight13932 ай бұрын
You save a lot of money on mechanics, but expend a lot of money on tools. Which will save money on the long run
@koblih6926 күн бұрын
No cleaning? No grease? No way!!!
@petew8238 Жыл бұрын
What about putting some slider pin grease on there. Cleaning up where the pads go. Heck maybe even a new rotor. Sliders could be seized. Oh boy
@Exceptionaldriver6192 жыл бұрын
Huh? Did you turn the rotors as well? You dont want uneven pads or rotors wear. Very important
@johnstaker67062 жыл бұрын
wdym turn the rotors?
@Exceptionaldriver6192 жыл бұрын
@@johnstaker6706 Because of what i said earlier... duh
@jack8356 Жыл бұрын
@@johnstaker6706 as in machine the rotors flat so your new pads can be bedded in. If you dont do it you will feel vibrations after a few months from speeds 60 + and also when coming to a stop. I know this bc i replaced pads only before. And rotor only also. The most important thing is to bedding the brake and pads. I think you could get away with not resurfacing the rotor if you just do the bedding procedure. Never done that before
@MySwagg93 Жыл бұрын
@@Exceptionaldriver619 they’re asking you to explain what that means, not be an a** about it..
@TheDawgButter Жыл бұрын
@@Exceptionaldriver619 I'm genuinely asking you because I'm curious as why turning the rotors matter when replacing brake pads? It prevents un even wear of the pads? I don't understand? What's causing the extra wear and tear?
@EricStevenTerry10 ай бұрын
Those break pads NEVER go back on that easy.
@chrispy4u28 ай бұрын
Ahhh yes the good ole pad slap
@jesusbravo5550 Жыл бұрын
Forgot to grease up guide pins and to resurface the rotors and measure if they are within specification. That is how you do it right. Not to mention tightening the lug nuts to the right torque spec with a torque wrench. No wonder those mechanics charge hundreds of dollars but do it right.
@PredaorGuy101 Жыл бұрын
I mean, if you do it right it’s not complicated enough to pay these mechanics all that money for a job well done. If you care about your car (and your wallet) you’ll look into all the details of how to do it, if you’re not already aware, and do it right the first time 👍🏻
@solas4446 күн бұрын
Mavis tried to charge me 270 for two front replacement brakes only.
@sincerelyrob4240 Жыл бұрын
Do you have to bleed brakes?
@billpickelheimer6323 Жыл бұрын
Yeah ,NO DONT push the fluid backwards into the system , you will push all the crappy dirty fluid into the anti lock system and they don't like dirty fluid, you should clamp the hose and open the bleeder a little then push the piston in then close the bleeder the remove the clamp so
@jarellrogers89158 ай бұрын
I didn’t see him out the pins on. Don’t see them on when he’s finished either.
@wilE6764 Жыл бұрын
Can you show drum brakes next?
@MattGuzman-ng2yx10 ай бұрын
Uhhh, what about bleeding the lines? 🤔
@OddDevDGAF Жыл бұрын
Why do you need to compress the caliper
@siiioxide Жыл бұрын
at least use the star pattern if your not going to torque the wheel nuts