This is BY FAR the easiest to understand and most comprehensive beginner's guide to XFLR5. Thank you for sharing!
@TheImbeseal7 ай бұрын
I absolutely love xflr 5, as a beginner to these simulations I love how easy it is to get into and how in-depht you can go. It doesn't bombard you with options like some programs do, you can just click buttons and see what happens. Truly amazing.
@christopherwilson65275 ай бұрын
Thanks so much for this! Very clear to follow, and I can't wait to play around in XFLR5 now.
@adrianperez33752 жыл бұрын
Great video, and great to see you showcase the Prantdl D. I didn't expect to see it, but was pleasantly surprised.
@trse3332 жыл бұрын
I just want to huge thank you man. I appreciate yo your work. This helped me a lot.
@ericmartinez9034 Жыл бұрын
thanks man, really helped out for an assignment.
@miguelcardenes2774 Жыл бұрын
this helped me so much! Thank you!
@HowtosayaBadEnglish-ms4fg6 ай бұрын
Best video on xflr5
@dhanprasadpradhan Жыл бұрын
I think XFLR 5 is a good tool for noobs as well. Just knowing the nature of slope of cm vs alpha is sufficient enough to make something flyable. I have been using it for my own design validation, to get in depth it requires some more eye on.
@nicholasn.28832 жыл бұрын
This is dope
@deepak__422 жыл бұрын
My solution isn't converging even tho I'm changing the mesh size of wing
@FPIPedit Жыл бұрын
I have a problem with the cp location in xflr5.On condition that the angle of attack increases, the cp location will come to near the front side of the wing, but in my program, the cp location does not come to the front side of the wing on the contrary my cp location goes backward.
@ignaciosandoval46442 жыл бұрын
Great video Sid. When I compare the twisted vrs non twisted wing the total drag is higher, also L/D is smaller for the twisted wing. O.K. you don't need rudder but wing performance is poorer. Is this higly twisted wing a propper aproach for a reduced drag wing? thanks.
@GOAFPilotChannel Жыл бұрын
Depends on the wing. Twist should reduce induced drag and also reduce the tendency to tip stall.
@hatakeharsha Жыл бұрын
hey i cant see lift distribution in 3d view
@waluyoadisiswanto998221 күн бұрын
I did similar analysis, using type 1 analysis (fixed velocity). When I run another velocity, the streamline the same with that from different velocity. Did you try your analysis using different velocity? and see the streamline
@dominicagracefany71262 жыл бұрын
tutorial type 5 (beta range) please
@JK-je2ft Жыл бұрын
Hi Sid, I used your video for designing a foil for Windsurf foiling. This is currently a hot topic, because the sport is growing fast (and it is olympic). For my foil the parameters from your video may not work, as I assume a speed of 15m/s - but in water. Can you please give me a hint what to change at the analysis? For me the stall angel and the lift would be crucial, but the program says:"A+Ai+Twist = 3.5 could not be interpolated"
@GOAFPilotChannel Жыл бұрын
you need to run at alpha 3.5 Also for water you need to change the density in your analysis settings from 1.225 kg/m^3 to 1000kg/m^3. Also you will need to run your airfoils at ~1000x the reynolds numbers in xfoil
@flakmag1004 Жыл бұрын
my cant analyse, it keeps on popping up with "could not find the wings foil..." i followed the instructions step by step please help
@shivangsingh5834 Жыл бұрын
respected sir please help me, After clicking on to analyze GRAPHS are not appearing
@arispubg69192 жыл бұрын
Hello , when ı was analising program give crash Please , help me
@hussainhammed29428 ай бұрын
Hi Sid, thank you for your video. I'm struggling a bit with doing the plane analysis. I followed all your steps, and my points converged, but no data points were generated. Any advice?
@r9bet7 ай бұрын
I had a similar issue. I changed the Re for the foil analysis to 400,000 and ran it again and it worked for me.
@hussainhammed29427 ай бұрын
@@r9bet The problem is I'm trying to use this to model an RC plane for my dissertation, so the Reynolds is very low, so I'm not sure if that means I have to generate "unrealistic data" using a higher Reynolds and then provide an explanation in my disso.
@mark_slk4 ай бұрын
How to import airfoil to xflr5 on mac. I tried import .dat file and the airfoil didn’t show up
@tariqjavaid4690 Жыл бұрын
I have a query related to simulating an airfoil in XFLR5 which I am trying to import in dat file. Does this provide analysis on any airfoil which we can import or there is a predefined set of airfoils that can be simulated? In case of latter, how can I retrieve the available library?